EVVR CHW01 Energy Monitoring Smart Plug Instruction Manual

Energy Monitoring Smart Plug
Rev. A-032123
Instruction Manual

CHW01 Energy Monitoring Smart Plug

Thank you very much for purchasing the Evvr Energy Monitoring Smart Plug. Please read this manual carefully to learn about all the functions and uses of this Plug.
This Plug, which supports a maximum current of 16A, is designed to make almost any conventional home appliances smart. It is HomeKit-enabled, allowing you to fortlessly manage the connected appliance over your iPhone. When in use, the Plug will also continuously measure the electrical consumption of the connected appliance, and you can check this information at any time via the Evvr App installed on your iPhone.

Safety Precautions

• Caution: To avoid electric shock, DO NOT splash water on the device or touch the Switch Button with wet hands.
• Caution: This product is intended for indoor use only.
• Caution: Metal casings, mirrors, electrical appliances, etc., may afect, reduce, or interfere with wireless communication.

What’s in the Box

Please refer to the physical object for specifcs.

Part Names

Technical Specifcations

50/60Hz
Max. Load| Type F 16A
Type B 15A
Type G 13A
Wireless Standard| IEEE 802.11 b/g/n
Wi-Fi 2.4GHz
Power Consumption| 0.65W
Operating Temperature| -20~60°C
(-4°~140°F)
Storage Temperature| -40~85°C
(-40°~185°F)
Ambient Humidity| 5~85% RH
Length| 588 mm (23 inch)

Setup Instructions

This Plug uses Wi-Fi 2.4GHz networking. It is HomeKit-enabled and you can set it up on your iPhone.
When powered on for the frst time, the Plug will automatically go into the setup mode (indicated by a continuous blue blinking light).
In this mode, you can add the Plug to the Home App.

1. Open the Home App on your iPhone, tap “+”, and then tap Add Accessory.
2. Scan the QR code or input the 8-digit setup code.

Note: The setup mode will exit if there is no action performed in 10 minutes. If you want to set up the Plug again, please unplug it and plug it back in again to put it into setup mode once again.

Indicator Light Status

• Blue blinking (continuous): The Plug is in the setup mode.
• Blue blinking (3 blinks): The Button is disabled.
• Blue steady: The Plug is on; HomeKit & Wi-Fi are connected.
• Red blinking (continuous): Wi-Fi is disconnected.
• Red blinking (2 blinks): The Plug is restored to factory settings.
• Red blinking (3 blinks): The Plug is overloaded or exceeds the temperature limitRed steady: The Plug is on; HomeKit & Wi-Fi are disconnected.

Expanded Functionality with the Evvr App

When the Plug is in use, you can use the Evvr App to further expand the Plug’s functionality.
You can check electricity consumption, disable the button in case of unintended touch, and confgure the status of the Plug when it is re-powered on after a loss of power.

1. Install the Evvr App on your iPhone from the Apple App Store.
2. Allow the App to gain access to HomeKit’s devices.

Restore to Factory Settings

In case you need to restore the Plug to factory settings, please follow the instructions below:

1. Disconnect the Plug from power.
2. While pressing and holding the Button, reconnect the Plug to power.
3. Keep holding the Button for another 10 seconds until the red LED blinks twice.

Troubleshooting

Q1. Smart Plug pairing failed.

1. The device may be too far from the Wi-Fi router, or there may be interference in thecurrent network environment. Please try tobring devices closer to the Wi-Fi router.
2. The device may be already paired. Please return the device to factory defaults if youwant to pair it again.

Q2. Smart Plug cannot be controlled by Apple
Home APP.
The device may be installed too far from theWi-Fi router, or there may be signal interference. Please check whether there is strong electromagnetic feld equipment nearthe wireless switch and check whether the equipment is installed in a closed metal housing or in a closed concrete wall.

Legal Notice

Use of the Works with Apple badge means that an accessory has been designed to work specifcally with the technology identifed in the badge and has been certifed by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Apple, HomeKit, HomePod, HomePod mini, iPad, iPhone and Apple TV are trademarks of Apple Inc., registered in the U.S. and other countries and regions.

Certifcations (regional)

FCC ID: 2A68U-CHW01

FCC Statement
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment of and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Consult the dealer or an experienced technician for help.
Important Announcement Important Note
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Disposal Instructions

This product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic uipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects humanhealth and the environment. For more information about where you can drop of your waste equipment for recycling, please contact your local city ofce, your household waste disposal service or the shop where you purchased the product.

Warranty Policy

For warranty information, please visit https://www.evvr.io/warranty

Please contact us for any technical issue support@evvr.io

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>