SEALIGHT S2 Series AHDS20506-ZY LED Bulbs User Manual
- June 5, 2024
- SEALIGHT
Table of Contents
SEALIGHT S2 Series AHDS20506-ZY LED Bulbs
PRODUCT INTRODUCTION
-
Accessories list (pictures for reference):
-
Features:
CD Perfect beam pattern, fully illuminating the road during driving. ® High compatibility with Can BUS system, fit most vehicle’s systems
without error. @ Simple installation, plug and play, long life. -
Product specifications
Operating voltage| DC (9 – 16V)
---|---
IP rating| IP67
Color temperature| 6000-6500K
Operating temperature| -40°C-85°C
LED chips| High-brightness LED chips
Heat sink| 6063 aluminum alloy
Warranty| 2 years -
User instructions
- It is recommended to watch the headlight bulb installation video and installation instructions before installation.
- Please purchase the product through official channels, otherwise we won’t provide after-sales service.
- As the product has small & sharp parts, please keep it away from children.
- After receiving the product, please carefully check whether it is damaged or any part is missing. If there is any problem, please contact Customer Service .
- This product is only fit for vehicles which use 12V batteries. High voltage may cause damage.
CUSTOMERSERVICETEAM
E-mail: support@sealight-led.com
Tel: ( +1)805-538-4353
INSTALLATION INSTRUCTIONS
Matters needing attention
- CD The OE halogen bulb would be extremely hot for a quite long time after
- shutting down . To avoid burns, please wait at least 0.5 hours before replacing the lamps. Wear gloves while replacing the lamps, and do not touch the LED chips. If the lamps do not light-up , please unplug the power line, connect it reversely and try again.
Models: H8/H9/H10/H11/H16/9005/9006/9012
Installation instructions
-
Step 1: Remove the dust cover and the OE halogen bulb.
-
Step 2: Line-up the retainer holder with the slot of the assembly.
-
Step 3: Insert the lamps, turn them clockwise, then clamp tightly.
-
Step 4: Connect the power line.
Models: 9008/H13
Installation instructions
-
Step 1: Remove the OE halogen bulb
-
Step 2: Insert 9008/H13 into the assembly and rotate it clockwise, then lock it.
-
Step 3: Connect the power line.
Note: If necessary, adjust the position of the retainer holder, use a screw driver to take apart the screws, hold the base of lamp and rotate it to the right position (The LED chips should face 3-9 o’clock or power cable and ground are vertical). Place the screws back and fix them. -
Step 4: Sort and fix the wiring harness with Zip Ties.
Suggestions
Suggestions: According to most vehicles’ configurations, we recommend keeping the LED chips facing the 3 o’clock and 9 o’clock positions to ensure the best beam pattern and visual effect. However, It Is impossible to adjust to this position for some vehicles. There is no need to worry about the position of the LED chips as long as the beam pattern Is acceptable. Picture: LED chips facing 3 o’clock and 9 o’clock positions
If you are not satisfied with the light pattern and visual effect after installation, please operate and adjust according to the figure
- Adjust the buckle
- Adjust the direction of the light
FAQ
1. Q: The model of lamps I purchased is different from my OE halogen
lamps. Can I get an exchange for the correct model?
A: Please contact our Customer Service for a replacement.
2. Q: The size of the lamps is not correct, they’re either too long or too
wide, and LED lamps can’t be installed into the headlight assembly. How can I
get proper size lamps for my car?
A: Some LED lamps are not in a 1:1 ratio with the OE halogen bulbs. The large
base is for better heat dissipation and prolonging the life of the lamps. If
the lamps are not suitable for installation, Please contact our Customer
Service for a replacement.
3. Q: Do you meet the five phenomenons below?
(1) Errors on instrument panel;
(2) The Lamp keeps flashing;
(3) Can’t switch between high and low beams;
(4) High and low beam reversed;
(5) The Lamp does not turn on or off.
A: The above phenomenons are decoding problems, which are mainly caused by the
automotive computer failing to detect the correct signal. You can contact
Customer Service to obtain the decoder and solve the decoding problem.
4.Q: How to adjust the lamps to 3-9 o’clock? I’ve read all the
instructions, but still can’t find the method.
A: We recommend keeping the LED chips facing the 3 o’clock and 9 o’clock
positions to ensure the best beam pattern and visual effect. However, it is
impossible to adjust to this position for some vehicles. There is no need to
worry about the position of the LED chips as long as the beam pattern is
acceptable .
5.Q: The Daytime Running Lamps work incorrectly, it keeps flashing. How can
I solve the issue?
A: If your Daytime Running Lamp and High beam is the same bulb, the case would
be complicated to solve. Please contact Customer Service.
6. Q: After installing the LED lamps, I found my High beam and Low Beam
reversed. Is there any way to solve this problem?
A:lt is recommended to remove the lamp, rotate by 180 ° and install it again.
If the problem still exists, please contact Customer Service.
WARRANTY DESCRIPTION
Thank you for purchasing our products. All of our products are manufactured
with best quality control ; To protect your rights, you can extend the
warranty period for 6 months by contacting us via the links below.
Extended warranty period:
E-mail: support@sealight-led.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>