SEALIGHT H10 Series LED Fog Light Bulbs User Manual

SEALIGHT H10 Series LED Fog Light Bulbs User Manual

INSTALLATION-H11/H10/9006/5202

1. Removing the bulb compartment rubber cover and original bulb.

   • Remove the bulb compartment rubber cover (f present).
   • Press down on the connectors knob and disconnect the two pars.
   • Tum the bulb counter-clockwise and then remove the original bulb.
     

2. Insert the LED bulb into the bulb compartment, Align the tab parts of the LED bulb with the groove sections of the locking ring,

**LEDBULB:

LOCKING RING:
**

3. While pushing the bulb down, tur it clockwise unti it cannot tum anymore and then ensure the LED bulb is securely in place. (excluding model 5202)
   “The LED bulb should be fitted so that the lefUright sides of the bulb containing the LED elements are each facing 3 and 9 o’clock.
   

4. Attach the LED bulb connector with the original vehicle connector and reinstall the rubber cover (i present).

WARNINGS FOR USE

WARNINGS FOR USE

• Do not ook directly at the LED bulb for any period of time when it is timed on, as this may cause serious eye injury.
• Please do ot disassemble or modify the product in any way, as this may damage the product or cause fire and/or personal njury.
• If there is any abnormal vibration or sound when the vehicle is moving, stop immediately in a safe location and check the vehicle Do not wash the vehicle with the fog lights turned on, as sudden changes in temperature may cause an unexpected reaction from the LED bulb.
• The LED bulb body and LED surface can become extremely hot. Do not touch these areas with bare hands or allow any skin contact as this could resultin severe bums,
• During heavy rain or when putting the vehicle through a car wash after the fog lights have been on, condensation may build up inside the bulb compartment. This s due to a difference in temperatures inside and outside the bulb compartment. Please note that this wil not affect the operation of
  the fog light.

TROUBLE SHOOTING

The lights are notworking properly|

1. Check that the power connectors are properly connected, and ensure that the vehicle fog light sare switched ON.
2. Ensure that the vehicle has enough battery power to supply the LED bulbs.
3. Install the LED bulbs with the resistors (CAN bus).

---|---
One of the bulbsis not working| Make sure the connection is good. If one of thebulbs still doesn’t work, swap the left and rightside bulbs and test again. If the problem cannotbe resolved, it may be caused by the vehicle’slight assembly.
The lights flickeror flash| Install the LED bulbs with the resistors(CANbus) to resolve this issue.
A warning lampappears on thevehicle’s maindash board system| This may happen because the low-wattage LED bulbs are not being recognized by thevehicle’s system. This can be resolved by the installation of an additional set of resistors(CANbus).

FAQ

1.Q: The model of lamps | purchased s different from my OE halogen lamps.

Gan | get an exchange for the correct model?

A: The main reasons: (1) Amazon Confirmed Fit system is not 100% accurate. (2) Your headight assembly is not an OE part, Please double check the model of your O halogen bulb. And contact our Customer Service for an exchange.

2.0:The size of the lamps is not correct, they're either toa long or too

wide, and LED lamps can't be installed into the headlight assembly. How can | get proper size lamps for my car?

A: Some LED lamps are not in a 1:1 ratio with the OF halogen bulbs. The large base is for better heat dissipation and prolonging the lfe of the lamps. If the lamps are ot suitable for installation, please contact the Customer Service.

‘

3.0: Do you meet the five phenomenons below? (1) Ertors on instrument

panel; (2)The Lamp keeps flashing: (3) The Lamp does not turn on or of.

The above phenomenons are decoding problems, which are mainly caused by the automotive computer failing to detect the correct signal. You can contact Gustomer Service to obtain the decoder and solve the decoding problem.

PRODUCT SPECIFICATIONS

WARRANTY DESCRIPTION

‘Thank you for purchasing our products. All o our products are manufactured with best quality control ; To protect your rights, you can extend the warranty period for 6 months by contacting us via the links below or send us a email. Extended warranty period:
E-mail: support@sealight-led.com Links: https://sealight-ed.com/membership.
Made In China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>