Joie i-Harbour i-Spin Grow R Signature Collection Child Seat Instruction Manual

Joie i-Harbour i-Spin Grow R Signature Collection Child Seat

Parts List

Please make sure there are no missing parts. Please contact the retailer if anything is missing.

1. Head Support
2. Seat Pad
3. Buckle
4. Webbing Adjustment Button
5. Adjustment Webbing
6. Recline Adjustment Button
7. ISOFIX Guides
8. Rotation Button
9. Shoulder Harness Covers
10. Infant Insert
11. Head Support Adjustment Lever
12. Side Impact Protection Pod
13. Infant Carrier Rotation  Button
14.  ISOFIX Adjustment Button
15. Child Restraint Release Button
16.  Load Leg
17.  Load Leg Adjustment Button
18. ISOFIX Connector
19. Instruction Manual Storage Compartment

WARNING

CAREFULLY read the warnings given in the separate Safety Manual to ensure a secure usage of the product.

Emergency
In case of emergency or accidents, it is most important to have your child taken care of with first aid and medical treatment immediately.

Product Information

1.  This is an “ i-Size ” Enhanced Child Restraint System. It is approved according to UN Regulation No.129, for use in, i-Size compatible vehicle seating positions as indicated by vehicle manufacturers in the vehicle users’ manual.
2. If in doubt, consult either the Enhanced Child Restraint System manufacturer or the retailer.

Materials
Patent No.
Plastics, metal,
fabrics

Choose Your InstallationPatents pending

Installation Concerns

Base Installation

1.  Attach the ISOFIX guides to the vehicle’s ISOFIX anchor points (see vehicle owner’s manual). 1 The ISOFIX guides can protect the surface of the vehicle seat from being torn. They can also guide the ISOFIX connectors.

2.  Unfold the load leg from storage compartment.

3.  Extend the ISOFIX connectors by pressing the ISOFIX adjustment button while pulling on the connector.  Press the ISOFIX adjustment button to adjust the ISOFIX connectors. Line up the ISOFIX connectors with the ISOFIX guides, and then click both ISOFIX connectors into the ISOFIX anchor points.

4.  Make sure that both ISOFIX connectors are securely attached to the vehicle’s ISOFIX anchor points. There should be two audible clicks and the colors of the indicators on both ISOFIX connectors should be completely green.

5.  Check to make sure the base is securely installed by pulling on both ISOFIX connectors.

6.  After placing the base on the vehicle seat, extend the load leg to floor 5 . When the load leg is installed correctly, the load leg indicator will show green. Red will be shown when installed incorrectly.

7.  The load leg has multiple positions. When the load leg indicator shows red this means the load leg is in the wrong position.

8.  Make sure the load leg is in full contact with the vehicle floor pan.

9. Squeeze the load leg adjustment button, then shorten the load leg upwards.

10.  The completely assembled base is shown as

11. The ISOFIX connectors must be attached and locked onto the ISOFIX anchor points.

12. The load leg must be installed correctly with green indicator.
    Removing the Base

13. To remove the base from the vehicle seat, push the secondary lock buttons 7 -1 first and then press the ISOFIX releasing buttons 7 -2 on the ISOFIX connectors before removing the base from the vehicle seat.

14. For transporting, press ISOFIX adjustment button and move the ISOFIX connectors back into the storage position.

Use Side Impact Protection

1.  The enhanced child restraint is delivered with a removable side impact protection pod. This side impact protection pod MUST be used on the door side of the vehicle. Installation shown in.
2.  Press the release button to remove the side impact protection pod.

Height Adjustment

1.  Please adjust the head support and check if the shoulder harnesses are at the correct height according to 11 & 12 & 13 & 14
   •  When used in rearward facing mode, the shoulder harness height must be even with or just below the top of child’s shoulders. 11
   • When used in forward facing mode, the shoulder harness height must be even with the top of child’s shoulders. 12
   • Pull the head support adjustment lever 13 , meanwhile pull up or down the head support until it snaps into one of the 6 positions. The head support positions are shown as 14 .

Recline Adjustment

Squeeze the recline adjustment button to adjust the enhanced child restraint to the proper position. 15
Both rear facing mode and forward facing mode have 5 recline positions, the recline angles are shown as 16 .

Rearward Facing Mode

(Child height 40cm-105cm/ Child weight 18.5kg)

Please install the enhanced child restraint on the rear vehicle seat and then put the child in the enhanced child restraint.

1.  Push the enhanced child restraint down onto the base 17 . If the enhanced child restraint is secure, the enhanced child restraint indicator will show green. 18

2.  To release the enhanced child restraint, first take the child out of the child restraint. Pull the child restraint release button 19 -1, then lift the child restraint up 19 -2.

   • The enhanced child restraint can ONLY be installed and released when in rearward facing mode.

3.  Press and hold the ISOFIX adjustment button and push the enhanced child restraint system back until it comes in contact with the vehicle seatback. 20

4. Press and hold the rotation button to rotate for easier side loading/unloading of the child, then rotate the seat to the rear facing position. 21

   • Press the rotation button on either side to rotate the enhanced child restraint.

5.  Press the harness adjustment button while pulling the shoulder harnesses to the desired length (Pull from below the fixed shoulder pads to lengthen). 22

6. Unlock the buckle of the harnesses by pressing the red button. 23

7.  Place the buckle tongues against the magnetic area on the outer side of the enhanced child restraint so that the tongues are held in place. 24
   Use Infant Insert

8.  Place the child into the enhanced child restraint and pass both arms through the harnesses.

9.  Engage the buckle. Please refer to 25

10.  Rotate the enhanced child restraint to the rear facing position. The enhanced child restraint indicator will show green. 26

11.  Pull down the adjustment webbing and adjust it to the proper length to make sure your child is properly secured. 27
    Always keep child secured in harness and properly tightened byremoving any slack.

Forward Facing Mode

(Child height 76cm-105cm/ Child weight 18.5kg/ Child’s Age 15 Month)

1. * Please install the enhanced child restraint on the rear vehicle seat, and then place the child in the enhanced child restraint.

2.  Press the rotation button to rotate for easier side loading/unloading of the child, then rotate the seat to the forward-facing position. 28

   • Press the rotation button on either side to rotate the enhanced child restraint.

3.  Press the harness adjustment button while pulling the shoulder harnesses to the desired length (Pull from below the fixed shoulder pads to lengthen). 29

4.  Unlock the buckle of the harnesses by pressing the red button. 30
   Remove the infant insert when in forward facing mode.

5.  Place the buckle tongues against the magnetic area on the outer side of the enhanced child restraint so that the tongues are held in place. 31

6.  Rotate the enhanced child restraint seat to forward facing the enhanced child restraint indicator will show green. 32

7. Pull down the adjustment webbing and adjust it to the proper length to make sure your child is properly secured. 33

   • Always keep child secured in harness and properly tightened by removing any slack.
   • DO NOT use forward facing unless your child is at least 76cm AND 15 months old.

Detach Soft Goods

Press the red button to disengage the buckle. 34
Follow steps 35 – 40 to detach soft goods.
To re-attach the soft goods please repeat the above steps in the reverse order.

Care and Maintenance

• Please store the infant insert somewhere out of the child’s reach.
• Please wash the soft goods with cold water under 30°C.
• Do not iron the soft goods.
• Do not bleach or dry clean the soft goods.
• Do not use undiluted detergents gasoline or another organic solvent to wash the enhanced child restraint or base. It may cause damage to the enhanced child restraint.
• Do not twist the soft goods to dry with great force. It may leave the soft goods with wrinkles.
• Please hang dry the soft goods in the shade.
• Please remove the enhanced child restraint from the vehicle seat if it will not be in use for a long period of time.

References

• Baby Gear That Goes Above & Beyond | Joie
• Joie's Signature Collection | Luxury Baby Gear

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>