Joie i-Prodigi Enhanced Child Restraint Instruction Manual

Joie i-Prodigi Enhanced Child Restraint Instruction Manual

Introduction

You have purchased a high quality﹐ fully certified child safety child restraint. This product is suitable for the use of children with height 40cm125cm and weight up to 22.5kg. Carefully read this Instruction Manual and follow the installing steps because this is the ONLY way to protect your child from serious injury or death in case of an accident﹐ and to provide comfort to your child while using this product. Keep this instruction manual for future reference.

Please confirm

• To use this Joie enhanced child restraint with the i-Size ISOFIX connections according to the UN Regulation No.129, your child must meet the following requirements.

• Rearward Facing: Child height 40cm-125cm/ max. 22.5kg;

• Please read all the instructions in this manual before installing and using the product.
  IMPORTANT: KEEP FOR FUTURE REFERENCE. PLEASE READ CAREFULLY.

• Please keep the instruction manual in the storage compartment at the back of the seat as right figure.

• For warranty information, please visit our website at joiebaby.com

Parts List

Please make sure there are no missing parts.
Please contact the retailer if anything is missing.

1. Head Support
2. Seat Pad
3. Rebound Bar
4. Recline Adjustment Button
5. Load Leg Adjustment Button
6. Load Leg Indicator
7. Load Leg Adjustment Button
8. Load Leg
9. Buckle
10. Shoulder Harness Covers
11. Infant Insert
12. Head Support Adjustment Lever
13. Side Impact Protection Pod *must use on door side only
14. Rebound Bar Adjustment Webbing
15. Rebound Bar Release Button
16. ISOFIX Connector
17. ISOFIX Guides
18. ISOFIX Adjuster Button
    

WARNING

• CAREFULLY read the warnings given in the separate Safety Manual to ensure a secure usage of the product.

Emergency

In case of emergency or accidents, it is most important to have your child taken care of with first aid and medical treatment immediately.

Product Information

1. This is an “ i-Size ” Enhanced Child Restraint System. It is approved according to UN Regulation No.129, for use in, i-Size compatible vehicle seating positions as indicated by vehicle manufacturers in the vehicle users’ manual.
2. If in doubt, consult either the Enhanced Child Restraint System manufacturer or the retailer.

• Materials: Plastics, metal, fabrics
• Patent No: Patents pending

Installation Mode

ECE R129| Child’s Size| Installation Mode| Figure for Installation| Seat Position
---|---|---|---|---
40cm-125cm/ 22.5kg| Rear Facing mode| | Position 1-8

Installation Concerns

Base Installation

1. Attach the ISOFIX guides to the vehicle’s ISOFIX anchor points (see vehicle owner’s manual). 1 The ISOFIX guides can protect the surface of the vehicle seat from being torn. They can also guide the ISOFIX connectors.

2. Unfold the load leg from storage compartment. 2

3. Extend the ISOFIX connectors by pressing the ISOFIX adjustment button while pulling on the connector. 3

4. Press the ISOFIX adjustment button to adjust the ISOFIX connectors. Line up the ISOFIX connectors with the ISOFIX guides, and then click both ISOFIX connectors into the ISOFIX anchor points. 4

   • Make sure that both ISOFIX connectors are securely attached to the vehicle’s ISOFIX anchor points. There should be two audible clicks and the colors of the indicators on both ISOFIX connectors should be completely green. 4 -1
   • Check to make sure the base is securely installed by pulling on both ISOFIX connectors.

5. Pull the rebound bar towards the back of the vehicle and lock into place by pulling the rebound bar adjustment webbing. 5

6. After placing the base on the vehicle seat, extend the load leg to floor 6 When the load leg is installed correctly, the load leg indicator will turn green. It will turn red when installed incorrectly. 6 -2

   • The load leg has multiple positions. When the load leg indicator turns red this means the load leg is in the wrong position.
   • Make sure the load leg is in full contact with the vehicle floor pan.
   • Squeeze the load leg adjustment button, then shorten the load leg upwards. 6 -1

7. The completely assembled base is shown as 7

   • The ISOFIX connectors must be attached and locked onto the ISOFIX anchor points. 7 -1
   • The load leg must be installed correctly with green indicator. 7 -2
     Removing the Base

8. To remove the base from the vehicle seat, push the secondary lock buttons 9 -1 first and then press the ISOFIX releasing buttons 9 -2 on the ISOFIX connectors before removing the base from the vehicle seat. 9

9. Before transporting the seat, press ISOFIX adjustment button and move the ISOFIX connectors back into the storage position. 10

see images 1 – 10

Use Side Impact Protection

1. The enhanced child restraint is delivered with removable side impact protection pod. This side impact protection pod MUST be used on the door side of the vehicle. Installation shown in 11 .
2. Press the release button to remove side impact protection pod. 12

**see images 11 – 12

**

Height Adjustment

for Head Support and Shoulder Harnesses

1. Please adjust the head support and check if the shoulder harnesses are at the correct height according to 13&14
   • The shoulder harness height must be even with or just below the top of child’s shoulders. 13
     Lift up the head support adjustment lever, meanwhile pull up or down the head support until it snaps into one of the 8 positions. The head support positions are shown as 14 .

**see images 13 – 14

**

Recline Adjustment

Squeeze the recline adjustment button to adjust the enhanced child restraint to the proper position. 15
Adjust the seat recline to any of the 8 recline positions for optimal head and neck support. 16

Rearward Facing Mode

(Child height 40cm-125cm/ Child weight 22.5kg)

• * Please install the enhanced child restraint on the rear vehicle seat and then put the child in the enhanced child restraint.

1. Press the harness adjustment button while pulling the shoulder harnesses to the desired length (Pull from below the fixed shoulder pads to lengthen). 17
2. Unlock the buckle of the harnesses by pressing the red button. 18
3. Fix the buckles on the both sides of seat to make placing the baby more convenient. 19
4. Place the child into the enhanced child restraint and pass both arms through the harnesses.
5. Engage the buckle. Please refer to 20
6. Pull down the adjustment webbing and adjust it to the proper length to make sure your child is properly secured. 21
   • Always keep child secured in harness and properly tighten the harness by removing any slack.

**see images 17 – 21

** Use Infant Insert

We recommend using the full infant insert while the baby is under 60cm. It can be used until they outgrow the insert. The infant insert increases side impact protection.| |

Remove the head support portion of the infant insert when the child’s

head no longer fits comfortably.

---|---|---
| Remove the body portion of the infant insert when the infant’s shoulders no longer fit comfortably.
|

Remove the infant insert cushion by detaching the snaps to allow more space when the infant does not fit comfortably. The cushion can be used separately without being attached to the insert to bolster the infant’s back for more comfort.

Detach Soft Goods

• Press the red button to disengage the buckle. 22
• Follow steps 23 – 27 to detach soft goods.
• Make sure to adjust the seat to any of the recline positions between 3-8 before pull out the plastic clips at the seat cover bottom. 26 -1
• To re-attach the soft goods please repeat the above steps in the reverse order.

**see images 22 – 27

**

Care and Maintenance

• Please store the infant insert somewhere out of the child’s reach.
• Please wash the soft goods with cold water under 30°C.
• Do not iron the soft goods.
• Do not bleach or dry clean the soft goods.
• Do not use undiluted detergents gasoline or other organic solvent to wash the enhanced child restraint or base. It may cause damage to the enhanced child restraint.
• Do not twist the soft goods to dry with great force. It may leave the soft goods with wrinkles.
• Please hang dry the soft goods in the shade.
• Please remove the enhanced child restraint from the vehicle seat if it will not be in use for a long period of time.
  

Customer Support

Allison Baby UK Ltd,
Venture Point, Towers Business Park
Rugeley, Staffordshire, WS15 1UZ
NUNA International B.V.
Van der Valk Bourmanweg 178 C,
2352 JD Leiderdorp, The Netherlands
view all fine signature selections at
joiebaby.com/signature

References

• Baby Gear That Goes Above & Beyond | Joie
• Joie's Signature Collection | Luxury Baby Gear

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>