Joie signature i-Traver signature Booster Seat Instruction Manual

i-Traver signature Booster Seat
Instruction Manual

ECE R129/03: ISO/B2
ECE R129/03: i-Size

i-Traver signature Booster Seat

ECE R129/03 Child height 100cm-150cm
Welcome to Joie ™
Congratulations on becoming part of the Joie family! We are so excited to be part of your journey with your little one. While traveling with the i-Traver™ series high back booster you are using a high quality, fully certified safety enhanced child restraint. Please carefully read this manual and follow each step to ensure a comfortable ride and best protection for your child.
To use this Joie booster with the ISOFIX connections according to ECE R129/03, your child must meet the following requirements. Child height 100cm-150cm (Reference age 3.5-12 years).
Booster
Please read all the instructions in this manual before installing and using the product.
! IMPORTANT: KEEP FOR FUTURE REFERENCE. PLEASE READ CAREFULLY.
Please keep the instruction manual in the   storage compartment at the bottom of   the booster as right figure.
For warranty information, please visit our website at joiebaby.com

Parts List

Make sure all parts are available before assembly. If any part is missing, please contact local retailer. No tools are required for assembly.

WARNING
! NO booster can guarantee full protection from injury in an accident. However, proper use of this booster will reduce the risk of serious injury or death to your child.
! Always take care to follow the installation instructions correctly, this will ensure the booster performs at an optimum safety level.
! Do take care so that the rigid items and plastic parts of an booster shall be so located and installed that they are not liable to become trapped by a move- able seat or in a door of the vehicle.
! To use this booster seat according to the ECE R129/03, your child must meet the following requirements.
Child height 100cm-150cm (reference age: 3.5-12 years). Forward facing only (in vehicle travel direction)
! The booster may not fit to all vehicles for the usage from 135cm-150cm.
! Any straps holding the booster to the vehicle should be tight and the straps should not be twisted.
! The booster seat should be replaced if it has been subjected to heavy loads in the event of an accident or if it has been dropped.
! This booster seat is only intended to be used in the car.
! Do not make any alterations or additions to the booster seat without approval from the type approval authority. DO NOT remove any of the white EPP/EPS foams. Failure to do so may result in serious safety issues.
! DO NOT use the seat if the surfaces are too hot from sunlight.
! Never leave the child unattended in the booster seat or vehicle, not even for a few minutes.
! Any luggage or other objects liable to cause injuries in the event of a collision shall be properly secured.
! The booster shall not be used without the soft goods.
! The booster soft goods should not be replaced with any other than the one recommended by the manufacturer, because the soft goods constitutes an integral part of the restraint performance.
! Always secure child in booster, even on short trips, as this is when most accidents occur.
! DO NOT leave this booster, or other items unbelted or unsecured in your vehicle. Remove the booster seat from the car if not regular used and store in a dry, sun-protected surrounding.
! It’s recommended not to use a second-hand booster seat whose history is not known. It may have invisible structural damages or defects due to incorrect usage/storage.
! DO NOT use any load bearing contact points other than those described in the instructions and marked on the booster.
! DO NOT install this booster under the following conditions:

1. Vehicle seats facing sideways or rearward with respect to the vehicle’s direction of travel.
2. Vehicle seats movable during installation.

! Consult the retailer for issues concerning maintenance, repair and part replacement.

Emergency

In case of emergency or accidents, it is most important to have your child taken care of with first aid and medical treatment immediately.

Product Information

1. This is an Enhanced Child Restraint System, intended to use as a Non-integral Universal Enhanced Child Restraint System (i-Size booster seat) from 100-150cm.
2. It is approved to the latest UN Regulation R129/03.

Booster Assembly

see images 1 – 5

1. Squeeze the head support adjustment latch first and then slide in lower back support under the fabric cover to connect them together. 1

2. ! CHECK to make sure two pieces are securely snapped together by pulling on them.

3. To attach the lower back support to the base, hook the lower back support over the seat bar hinge on the base. 2

4. Rotate the lower back support up while holding the booster seat until it clicks into an upright position. 3

5. Align the side impact shield with the slot of lower back support plastics mounts, and then insert to lock. 4 5
   ! Please choose whether to install the side impact shield according to the size of the car.

Adjust the seat

see images 6
There are 3 positions for seat and adjust the seat as 6

Height Adjustment – for Head Support

see images 7
Squeeze the head support adjustment lever while pulling up or down on the head support until it snaps into one of the 10 positions. 7

Concerns on Installation

see images 8 – 11

Installation using ISOFIX System and 3-point belt or using 3-point belt only
(Forward Facing Mode/ for Child between 100cm150cm / 3.5–12 years old) see images 12 – 24
If vehicle is equipped with ISOFIX, the vehicle lower anchor points may be visible at the vehicle seat crease. See your vehicle owner’s manual for exact locations, anchor identification, and requirements for use.

1. Fit the ISOFIX guides with the ISOFIX anchor points. 12 The ISOFIX guides can protect the surface of the vehicle seat from being torn. They can also guide the ISOFIX connectors.

2. Press the ISOFIX adjusting button to pull out the ISOFIX connectors. 13
   Rotate the ISOFIX connectors 180 degrees until they are pointing in the direction of the ISOFIX guides. 14
   

3. Line up the ISOFIX connectors with the ISOFIX anchor points, and then click both ISOFIX connectors into the ISOFIX guides. 15
   ! Make sure that both ISOFIX connectors are securely attached to their ISOFIX guides. The colors of the indicators on the both ISOFIX connectors should be completely green. 15
   ! Check to make sure the booster is securely installed by pulling on the both ISOFIX connectors.

4. To remove the booster:
   a. Press the secondary lock button 16-1
   -1 first and then the button 16-2
   -2 on the ISOFIX connectors before removing the booster from the vehicle seat.
   b. Rotate the ISOFIX connectors by 180 degrees, then press the ISOFIX adjusting button to fold the ISOFIX connectors. 17
   

! Pull the vehicle safety belt and pass through the belt path 20 , and then buckle it up. 20 -3
! Could also be installed by using 3-point belt only. (see images 20 – 24 )
! Position shoulder belt through the shoulder belt guide shown in 20 -1
! DO NOT position vehicle belt over top of the armrests. It must pass underneath the armrests. 20 -2
! The booster can not be used if the vehicle safety belt buckle (female buckle end) is too long to anchor the booster securely. 20 -4
! After your child is placed in this booster, the safety belt must be used correctly, and ensure that any lap strap is worn low  down, so that the pelvis isfirmly engaged. 20
! To ensure the correct head support height is obtained, the  bottom of the headrest MUST be even with the top of child’s shoulders as shown in 21 and the shoulder belt must be positioned in the green zone as shown in 22
! Place a booster firmly against the back of a forward-facing vehicle seat equipped with a lap/shoulder belt.
! Make sure, that the shoulder belt portion of the vehicle belt goes straight through the shoulder belt guide as shown in 23
! Tighten the vehicle belt by pulling the shoulder strap until all belt slack is removed.
! I f the belt lays across child neck, head or face, readjust head support height.
! Any straps holding the booster to the vehicle should be tight  and the straps should not be twisted.

Detach Soft Goods

see images 25 – 28

To refit the seat pad simply reverse the steps above.

Care and Maintenance

! Please wash the soft goods and inner padding with cold water under 30°C.
! Do not iron the soft goods.
! Do not bleach or dry clean the soft goods.
! Do not use undiluted neutral detergent, gasoline or other organic solvent to wash the booster. It may cause damage to the booster.
! Do not twist the soft goods and inner padding to dry with great force. It may leave the soft goods and inner padding with wrinkles.
! Please hang dry the soft goods and inner padding in the shade.
! Please remove the booster from the vehicle seat if not in use for a long period of time. Put the booster in a cool, dry place and somewhere your child cannot access it.

Allison Baby UK Ltd,
Venture Point, Towers Business Park
Rugeley, Staffordshire, WS15 1UZ
NUNA International B.V.
Van der Valk Bourmanweg 178 C,
2352 JD Leiderdorp, The Netherlands
view all fine signature selections at
joiebaby.com/signature
IM-000373G

Documents / Resources

| Joie signature i-Traver signature Booster Seat [pdf] Instruction Manual
i-Traver signature, Booster Seat, i-Traver signature Booster Seat, Seat
---|---

References

• Baby Gear That Goes Above & Beyond | Joie
• Joie's Signature Collection | Luxury Baby Gear

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>