Midea Envi 12H Mobile Air Conditioner User Manual

June 5, 2024
Midea

Midea Envi 12H Mobile Air Conditioner

Thank you for purchasing our product.
Before using this unit, please read this manual in order to avoid improper handling and use of the device.

  • Follow local grid interconnection rules while installing the air conditioning and ensure that it is properly grounded. If you have any question on electrical installation, follow the instructions of the manufacturer, and if necessary, ask a professional electrician to install it.
  • Place the machine in a flat and dry place and keep a distance of above 50cm between the ma-chine and the surrounding objects or walls.
  • After the air conditioning is installed, ensure that the power plug is intact and firmly plugged into the power outlet, and place the power cord orderly to prevent someone from being tripped or pulling out the plug.
  • Do not put any object into the air inlet and outlet of the air conditioning. Keep the air inlet and outlet free from obstructions.
  • When drainage pipes are installed, ensure that the drainage pipes are properly connected, and are not distorted or bended.
  • While adjusting the upper and lower wind-guide strips of the air outlet, pluck it with hands gently to avoid damaging wind-guide strips.
  • When moving the machine, make sure that it is in an upright position.
  • The machine should stay away from gasoline, flammable gas, stoves and other heat sources.
  • Don‘t disassemble, overhaul and modify the machine arbitrarily, otherwise it will cause a machi-ne malfunction or even bring harm to persons and properties. To avoid danger, if a machine failure occurs, ask the manufacturer or professionals to repair it.
  • Do not install and use the air conditioning in the bathroom or other humid environments.
  • Do not pull the plug to turn off the machine.
  • Do not place cups or other objects on the body to prevent water or other liquids from spilling into the air conditioning.
  • Do not use insecticide sprays or other flammable substances near the air conditioning.
  • Do not wipe or wash the air conditioning with chemical solvents such as gasoline and alcohol. When you need to clean the air conditioning, you must disconnect the power supply, and clean it with a half-wet soft cloth. If the machine is really dirty, scrub with a mild detergent.
  • The appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities if they have been given supervision or instruction concer-ning use of the appliance in a safe way and understand the hazards involved.
  • Children shall not play with the appliance.

Features

  • With cooling, heating, dehumidification and air supply function.
  • Automatic swing leaf in the outlet has automatic air swing function. If the air swing function is in operation, you can press the SWING button to stop the swing leaf at the desired angle.
  • LCD displays the control panel. High-quality LCD remote control is equipped to facilitate opera-tion. The remote control can be placed on the back of the body.
  • Handles on both sides adopt dividing point design, so that it is easer to carry it.
  • The handles on the rear of the air conditioner allow the power cord to be securely stored to prevent damage when carrying the air conditioner.
  • Air filtration capability.

Components

  1. Mask
  2. Top cover
  3. Swing leaf
  4. Rear housing
  5. Front housing
  6. Omni-directional wheel
  7. Exhuast pipe assembly
  8. Window sealing plate assembly
  9. Remote control
  10. Rear housing
  11. EVA filter housing
  12. Power cord hook
  13. Handle
  14. Air vent
  15. Continuos drainage hole
  16. CON filter screen
  17. Air inlet grille
  18. Drainage hole
  19. Power cord
  20. Power cord plug

Installation

WARNING
Before using the mobile air conditioner, keep it upright for at least 2 hours. The air conditioner can be easily moved in the room. In the moving process, ensure that the air container is in the upright position and the air conditioner shoul be placed on a flat surface. Do not install and use the air conditioner in the bathroom or other humid environments.

  1. Install the heat pipe assembly, screw the heat pipe assembly into the exhaust port on the rear panel (counterclockwise).
  2. Install the window sealing plate assembly (Air Block – optional accessories). Midea-Envi-12H-Mobile-Air-Conditioner-3
  3. Pull the pipe towards the window and insert in into the hole in Air Block seal.
  4. Install the body

Move the machine with installed heat pipe and place it in front of the window. The distance between the body and walls or other objects should be at least 50 cm.

NOTICE
The pipe cannot be distorted nor has substantial turning (greater than 45 °). Keep the ventilation of the heat pipe unobstructed.

IMPORTANT NOTICE
The length of the exhaust hose shall be 280-1,500mm, and this length is based on the specifications of the air conditioning. Do not use extension tubes or replace it with other different hoses, or this may cause a malfunction.

Operation instruction

Instruction for operating

Midea-Envi-12H-Mobile-Air-Conditioner-5

  1. Timing key
  2. Wind speed selection key
  3. Up key
  4. Down key
  5. Display window
  6. Mode selection key
  7. Power key

When the machine is powered on for the first time, the buzzer will play power- on music and then the machine will get into standby status. Power key: press the key to turn on or turn off the machine. Mode selection key: in the case of power on, press the key to switch between cooling, air supply, dehumidification and heating mode. Up and Down key: press the two keys to change the set temperature or timing setting value, operate as follows: While setting temperature, press up key or down key to select the required temperature (not available in air supply or dehumidification mode). Simultaneously press both keys to switch between Celsius °C and Fahrenheit °F.

Wind Speed Selection key
In cooling and air supply mode, press the key to select high, medium or low wind speed operation. In heating mode, press the key to select high, medium or low wind speed operation. In dehumidification mode, pressing the key is invalid, and the fan will forcibly choose low wind speed operation

Timing key:
If the machine is powered on, press the key to turn or on turn off the timer. Press the key, when the timing symbol flashes, press up and down key to select the required timing value. Timing values can be set within 1-24 hours and the timing value is adjusted upwards or downwards by one hour.

Remote Control

Instruction for operating remote control:

  • Power: Press the key to tum on or turn off the machine.
  • Mode: press the key to switch between cooling, air supply, dehumidification and heating mode.
  • Up: press the key to increase temperature and timing set value.
  • Down: press the key to reduce temperature and timing set value.
  • Fan: press the key to select high, medium and low wind speed output circularly.
  • Timer: press the key to set timing value.
  • Swing: press the key to open or close swing style. Air flow of the air outlet can blow at different angles.
  • °C-°F: press the key to switch between Celsius and Fahrenheit.

A Variety of Protection Functions

Frost Protection Function:
In cooling, dehumidification or economic power saving mode, if the temperature of the exhaust pipe is too low, the machine will automatically enter protection status. If the temperature of the exhaust pipe rises to a certain temperature, it can automatically revert to normal operation.

Overflow Protection Function:
When water in the water pan exceeds the warning level, the machine will automatically sound an alarm, and the LDC temperature display area will show „FL“. At this point, you need to move the drainage pipe connecting the machine or the water outlet to sewer or other drainage area to empty the water.
After the water is emptied, the machine will automatically return to the original state.

Automatic Defrosting (heating and cooling models have this function):
The machine has automatic defrosting function, heating symbol on the display screen will flash.

Automatic Thermal Protection:
To protect the service life of the machine, the machine has automatic thermal protection in heating mode. During the protection period, the compressor and the lower motor will stop operation and will automatically return to normal heating state after the temperature of the machine recovers. To increase the service life of the compressor, it has a 3-minute delay booting protection function after the compressor is turned off.

Drainage Instruction

Manual drainage:
When the machine stops after the water is full, turn off the machine power and unplug the power plug.

Notice
Please move the machine carefully, so as not to spill the water in the water pan at the bottom of the body.

  • Place the water container below the side water outlet behind the body.
  • Unscrew the drainage cover, the water will automatically flow into the water container.

Notice
Keep the drainage cover properly. During drainage, the body can be tilted slightly backwards. If the water container cannot hold all the water and the water is still flowing, you can stop it to prevent water from flowing to the floor or the carpet. When the water is discharged, tighten the drainage cover properly.

Notice
Restart the machine after the drainage cover is installed, otherwise condensate water of the machine will flow to the floor or the carpet.

Continuous drainage (only applicable in cooling and dehumidification mode)

  • Unscrew the drainage cover.
  • Set the drainage pipe into the water outlet.
  • Connect the drainage pipe to the bucket or to the outlet (in case of drain, the condensate will drain spontaneously)

Maintenance

Cleaning: Before cleaning and maintenance, turn off the machine amd unplug the plug.

Clean the surface
Clean the surface of the machine with a wet soft cloth. Do not use chemicals, such as benzene, alcohol, gasoline etc. Otherwise, the surface or even the whole machine will be damaged.

Clean the filter screen
If the filter screen is clogged with dust, the effectiveness of the machine is reduced. Clean the filter screen once every 2 weeks.

  1. Retaining screw
  2. Wedging block

Cleaning the upper filter screen frame
Clasp the wedging block with hands. Force down from the outside to remove the filter screen frame. Unscrew 4 screws from the rear housing. Put the filter into warm water with neutral detergent (about 40°C/104°F) and then dry it.

Cleaning the lower filter screen frame
Hold the filter screen frame and pull it outward gently to remove it. Put the filter into warm water with neutral detergent (about 40°C/104°F) and then dry it.

Postseason storage
Unscrew the drainage cover and discharge the water into the water container. You can slightly tilt the body to dischrage the water. Turn on the machine, adjust it to low-wind ventilation mode and wait until the drainage pipes become dry, so as to storage the machine dry and prevent it from mildewing. Turn off the machine, unplug the power plug and wrap the power cord around handles in the back side of the machine and install the drainage cover.Remove the exhaust pipe and keep it properly. Cover the air conditioner with a plastic bag so as not to be dusty and place it into dry place and keep it out of reach of children. Remove the batteries from the remote control. Notice Ensure that the body is placed in a dry place and keep all components properly.

Troubleshooting

Do not repair or disassemble the air conditioning by yourself. Unqualified repairs will lead to failure of the warranty and may cause injury of persons or damage their properties.

Problems Reasons Solutions
The air conditioning does not work. There is no electricity. Turn it on

after connecting it to a socket with electricity.
The overflow indicator displays

„FL“.

| Discharge the water inside.
The ambient temperature is too low or too high?| Recommend to use the machine in at the temperature of 7-35 °C (44-95 °F).
In cooling mode, the room temperature is lower than the set temperature; in heating mode, the room temperature is higher than the set temperature.| Change the set temperature.
In dehumidification mode, the ambient temperature is low.| The machine is placed in a room with an ambient temperature of greater than 17 °C (62 °F).
The cooling or heating effect is not good.| There is direct sunlight.| Pull the Curtain.
Doors or windows are open; there are a lot of people; or in cooling mode, there are other sources of heat.| Close the doors and windows.
The filter screen is dirty.| Clean or replace the filter screen.
The air inlet or outlet is blocked.| Clear obstructions.
Big Noise| The air conditioning is not placed on a flat surface.| Put the air conditioning on a flat and hard place (to reduce the noise).
The compressor does not work.| Overheat protection starts.| Wait for 3 minutes until the temperature is lowered and then restart the machine.
The remote control does not work.| The distance between the machine and the remote control is too far.| Let the remote control get close to the air conditioning, and make sure that the remote control directly faces to the direction of the remote control receiver.
The remote control is not aligned with the direction of the remote control receiver.
Batteries are dead.
Displays ‚E1‘.| The pipe temperature sensor is abnormal.| Check the room temperature sensor and related circuitry.
Displays ‚E2‘| The room temperature sensor is abnormal.| Check the room temperature sensor and related circuitry.

If problems not listed in the table occur or recommended solutions do not work, please contact the professional service organization.

Schematic diagram

  1. Condenser
  2. Capillary
  3. Compressor
  4. Evaporator

The English version of the manual is an exact translation of the original manufacturer‘s instructions. Images used in this manual are for illustrational purposes only and may differ from the actual product.

WiFi Connection Guide

Install App
Download the ‘’Smart Life’’ app from the Play Store (android) or App Store (iOS).

Register
If you do not have a Smart Home account, register or sign in with a verification code sent by SMS.

To register:

  1. Tap to enter registration page.
  2. The system automatically recognises your country/area. You can also select your country code manually. Enter your mobile phone number/email address and tap ‘’Next’’.
  3. If you choose the mobile phone number option, then enter the verification code in the message sent to you by SMS. Set a password as prompted and press ‘’Confirm’’ to finish your registration.

Add Device Through Network

  1. Power air conditioner on, when air conditioner under standby mode, press the ‘’SPEED’’ button for 5 seconds to enter WiFi-connect mode.
  2. Open Smart Home app and tap ‘’+’’ in the upper right to add new device through the network.
  3. Ensure th device’s indicator light rapidly flashes (2times per second) and tap ‘’Confirm light is rapidly flashing’’.
  4. Select WiFi network (note: network must be 2.4Ghz band) and enter the password. The device will commence the pairing process and connect to the app.
  5. After successfully configuring the devices, the smart AC will be shown on the home page. Tap to enter its control page.

Note:

  • When device is online, it can be controlled.
  • When device is offline, it displays ‘’Offline’’ and can be remotely powered on.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals