SPY SHOP EUROPE BAETS1KZARC EUTech Audio Voice Recorder User Manual
- June 5, 2024
- SPY SHOP EUROPE
Table of Contents
EUTech Audio – voice recorder
User manual
BAETS1KZARC EUTech Audio Voice Recorder
- Made in the EU audio recorder with a strong magnet and 336 hours of recording time
- User-friendly Plug and Play
- Built-in high sensitivity microphone
- One button design
MAIN FEATURES
- 2 operating modes – continuous and voice activation
- 8GB integrated memory
- Approximately 336 hours of battery life in continuous and voice activation modes
- Very strong integrated magnet
- 72 x 25 x 38 mm and weighs 65 grams
- Ultra sensitive integrated microphone – detects voice up to 10m
- Sound Detection Level: 60dB
- High-quality recording mode: MP3 64Kbps
- Charging with the complimentary USB cable and 220V electricity adapter (not included)
- 2 x 3.7 volt 1,260 mAh rechargeable batteries (LI-polymer, Built-in Charger)
- ALC Function (Automatic Recording Level Control)
- Timestamp option available
- Battery life in standby mode: 350 days
- Battery charging time: approximately 20 hours
- Battery Indicator: LED Display (LED off while recording)
- USB 2.0
- Usage temperature: 0-40°
- Humidity: 20-80°
- Made in the EU
TWO OPERATING MODES
CONTINOUS
When you move the switch to CONT you will notice that the LED light (placed
close to the USB port) will light up red for about 5 seconds, and then will go
out meaning the recording has started. If you wish to stop the recording move
the switch to OFF otherwise the recording will continue until the battery runs
out or until the memory is full. In continuous recording mode, each video file
will be 5 hours long.
VOX (voice activation)
By moving the switch to VOX you will select the voice activation recording
mode. The red LED light will light up for about 5 seconds and afterward go off
meaning the function is activated. The device will pick up and save voice data
when it hears a sound. If no sound is detected for approximately 1 minute, the
device will go into standby mode and activate again if the sound is heard.
LED LIGHTS
SOLID RED LED LIGHT
When the device is charging the solid red light is on. As soon as the device
is fully charged the red light will start blinking. If the battery is
completely drained it will take approximately 28h for the audio recorder to
fully recharge.
RED LIGHT LIGHTS UP FOR 5 SEC AND THEN GOES OFF
When selecting either CONT or VOX recording modes, the red light will be
active for 5 seconds and then it will go off meaning the recording has
successfully started.
BLINKING RED LIGHT
When the device is connected to the charger and at the same time a recording
mode has been selected the red light will blink during the recording process.
ACCESSING THE STORED DATA – PLUG & PLAY
By simply attaching your audio recorder to the PC or laptop using the
complimentary USB cable you will be able to open the folder containing audio
files. Make sure your disk drive is set to FAT32 to be able to access the
recordings.
SETTING THE TIMESTAMP
Stored in a folder on the device itself you will find a program called Time
Setup V2.2. You need to run it, select the Mode (Record Quality) to be HQ,
SVOS Level +2, and you finally select Start. The program will generate the
.cfg file that needs to stay in the folder on the device itself.
SPECIAL NOTES
The device works with Windows operating systems only.
It is recommended to shut down the device every 14-15 days of usage and leave
it off for approximately 24h.
It is strongly suggested to fully discharge the battery at least every 25-30
days.
After accessing the recordings on the PC or laptop it is recommended to safely
remove the drive.
Contact Us:
Tel. +385 51 673 400
Fax. +385 51 671 542
Mail:
[email protected]
[email protected]