MONSTER MLB7-1074-RGB Smart Multicolor LED Lamp User Guide
- June 5, 2024
- Monster
Table of Contents
ARC+
SMART RGBW+IC LED LAMP
QUICK START GUIDE
MLB7-1074-RGB – V2.0 0122
GETTING STARTED
Thank you for choosing the Arc+ 3-In-1 Smart LED Lamp by Monster Smart
luminescence. This quick start guide will help you with the setup and
installation of your device.
WHAT’S IN THE BOX
- Arc+ Smart LED Lamp
- USB Type-C Power Cable
- Quick Start Guide
WHAT DO YOU NEED?
- Cellphone or tablet with Android 6.0 Marshmallow or higher/105 10 or higher
- Wi-R router with an Internet connection
- Wi-R 2.4GHz 802.11n
- 5V 3A / 9V 2.2A QC USB power source (not included) Before setup, make sure your phone is connected to the 2.4GHz
WI-Fl network that your Arc+ will be placed on. For easier pairing, turn
on Location and Bluetooth to quickly find nearby devices.
TIP : Do you know your Wi-Fi network name and password? Write it down now
if it’s hard to remember.
ANYTHING ELSE? The Arc+ is a Smart LED lamp, a headphone stand, and an
lOW wireless charger with USB charging to charge additional devices.
Additional devices and cables not included.
TIP: Save these instructions for future reference.
POWER/CHARGING
INPUT POWER To power the ARC+. plug the included USB Type-C cable into the input port at the back of the device, and the other end into a 5V 3A USB / 9V 2.2A QC USB power adapter (not included). Then, plug the power adapter into a powered AC outlet. The LED indicator at the rear of the device will illuminate red to indicate that it is powered. NOTES:
- Standard 5W wireless charging can be enabled by a 5V 3A USB power adapter.
- For IOW wireless fast charging, the Arc+ must be powered by a 9V 2.24 QC USB adapter (20W).
- Using a wall adapter providing less than the required power may result in improper charging and/or a fucker in the LED lighting.
- Always use the included 3A-rated USB Type-C power cable with this device.
USB CHARGING
Connect a USB charging cable to the USB-A port at the rear of the Arc+.
Connect the other end of that cable to your USB rechargeable devices such as
headphones or a mobile phone.
WIRELESS CHARGING
The Arc+ wireless charger is designed to work with QI Compatible wireless charging phones. Confirm that your phone is QI compatible before charging Place your Qi-enabled device on the wireless charger at the center of the Arc+ as illustrated below. The LED indicator at the rear of the product will illuminate blue to indicate that the device is charging.
Note: Wry thick protective cases can obstruct charging. For effective
charging, it may be necessary to reposition the phone or remove the case.
Caution- To prevent damage to the phone or the charger:
- Remove metal cases, or cases with any magnet/metal components before charging.
- Do not place metal objects on the charger during charging. Qi wireless chargeable phones with metallic-looking finishes will charge normally.
- NOTE: Wireless chargers generate heat when charging, and they may temporarily stop charging if it gets too hot.
- Multiple Qi devices cannot be charged at the same time. This witless charge Is destined for FC iPhone 12/12 Pro iPhone 12 Pro Max Pixel 5/5X1.. Peel 4/5. Nexus 7. Galaxy 520/520+ or higher. It IS also cornpattle vont all other 01 enable Wireless charging devices.
WIFI SETUP
STEP ‘1 Ensure that your Arc+ Is adequately powered.
STEP 2 Download the MONSTER SMART app from the App Store (for iPhone)
or Google Play Store (for Android phones).
NOTE: If desired, you can operate the product without pairing to VVI-Fi
and without the app. Advanced features like color customization, and
scheduling. and voice control will not be available.
STEP 3 Make sure your phone or tablet is successfully connected to the
24GHz WI-FI network that your Arc+will be placed on and ensure that your
Bluetooth Is enabled. Open the ad MONSTER SMART app and create an account
by following the on-screen instructions.
Monster Smart devices only work on a 2.46Hz Wi-Fi network. Many never home WI-
Fi networks are mixed networks that are set to 5GHz by default (ex: AT&T,
Verizon) and you may need to use AP pairing mode to connect If you Still has
difficulty, contact your Internet Service Provider for assistance with 7.4GHZ
network setup.
STEP 4 It Is recommended to first pair your Arc+ In a location close to
your router BEFORE installation. Press the power/mode button twice quickly to
turn the unit on. then press and hold to enter pairing mode. The Arc+ lights
will begin blinking when it has entered pairing mode and is ready to
pair.
Pairing Modes:
EZ MODE – RAPIDLY BUNKING LED (default) EZ Mode is the default mode for
quick and easy pair ng setup.
AP MODE – SLOWLY BLINKING LED access Port Mode is a secondary setup that
can help connect to mixed networks If you have trouble patina see
troubleshooting on page 7.
Note: Press and hold the power/mode button for 5-6 seconds to enter
pairing mode or change between pairing modes.
STEP 5 Confirm that the device Is In pairing mode. LED Is RAPIDLY blinking. In the am MONSTER SMART sninnT app, select the “+” in the upper right corner of the home screen to add a new device.
The app will detect the nearby Wi-Fi+BLE enabled device and ask if you would like to add it. click “Go to add”. Ensure that the device is checked and then click the “+” button
STEP 6 Confirm that the network displayed Is your 2.4GHz WI-Fl network, then enter your WI-Fl password and click ‘Confirm”.
Once complete, your device will be connected to the network Confirm or change the settings for your device and then click tone”. Your Arc+ is now set up and ready to use!
You can now use the app to add voice control (see pg 10), adjust settings, and create custom lighting effects. set schedules, and more!
TROUBLESHOOTING
HAVING TROUBLE WITH SETUP? Don’t return this product to the retailer,
we’re here to help. Please call/write us for customer support:
866-246-2008
customerservIce@monsterIllumlnessence.com
Q: Why is my device failing to connect to my Wi-A network?
Al: Make sure your phone or tablet is successfully connected to the 2AGHz WI-
Fl network that your device will be placed on.
A2: Make sure you enable Bluetooth and allow location services on your phone
or tablet to find nearby devices.
A3: If your Wi-Fl network is a mixed 2.4GHz/GHz network, try using AP pairing
mode for better results
- Press and hold the caking button until the LED Is story blinking
- In the app. select the n the upper right caner of the home screen to add a new device and then select “Lighting (/11-19)”.
- .Click Net Pairing Mode” in the upper right to switch to mode.
- Confirm that the LED indicator is slowly Idinkingsonfirm the network is your mind Wi-A network enter your WI-A password and click ‘Confirm”.
- Fellow on-screen instructions to set up your device via wireless access point_
A4: If you still have issues with your mixed network, you may need to access
your router settings and/or call your Internet 5enrice Provider to create a
separate 2.46Hz network. 0: Why is my phone not charging or fast charging?
Al: Your phone must be compatible with wireless charging.
A2: Cases or phone holders will interfere with wireless charging, please
remove them before use.
A3: Do not place any metal object other than your smartphone device within the
charging field.
A4: Ensure that your Arc+ is connected to sufficient power. Without meeting
the power input requirements, the features of the Arc+ will not function
properly.
0: Why is my headphone or another device not charging?
Al: Ensure that your Arc+ Is connected to sufficient power.
A2: Ensure that the charging cable you are using Is the correct cable for your
device.
For other frequently asked questions please visit our website at
www.monsterilluminessence.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>