Midea FW40-7JR 16 Inch Wall Fan with Remote Control Instruction Manual

Midea FW40-7JR 16-Inch Wall Fan with Remote Control

SPECIAL ANNOUNCEMENT

1. The Instruction has been proofread carefully. The company reserves the right to the interpretation thereof.
2. The product is subject to any technical improvement in the future without prior notice.
3. Any change in the appearance and color of the product shall be subject to the real object.
4. The pictures herein are only for reference.

WARNING

1. Do not leave the fan running unattended.
2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
3. To protect against the risk of electrical shock, do not immerse the unit, cord, or plug in water or other liquid.
4. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Young children should be supervised to ensure that they do not play with the appliance.
5. When the appliance is not in use and before cleaning, unplug the appliance from the outlet.
6. When the fan was assembled, the rotor blade guard shall not be taken off anymore.

RULES FOR SAFE OPERATION

1. Never insert fingers, pencils, or any other objects through the grille when fan is running.
2. Disconnect fan when moving from one location to another.
3. Be sure the fan is on a stable surface when operating to avoid overturning.
4. Do not use a fan in the window. Rain may create an electrical hazard.
5. Indoor use only.

ILLUSTRATION TO PARTS

Remark:
Due to the discrepancy among various modes of the products, please refer to the real objects upon installation. lustration is for reference only.

METHOD OF INSTALLATION

Assembly of the Guard and Blade

Install Rear Guard
Tun down the spinner and locking nut from the front of the motor shaft and then install the rear guard. Finally, put the locking nut back and screw-down it (as shown in Figure 1.).

Install Blades
Install the blades onto the motor shaft until the groove behind the blades reaches the fixing pin, and then tighten the spinner counter-clockwise ( as shown in Figure 2. ).

Install Front Guard
The structure of the circlip is classified into the straight-through type and the easy-pull-buckle type. Therefore, the front guard can be installed in the following two ways:

1. Method for installation of straight-through circlip: Normally, the circlip is installed with the front guard. Position the decorating ring of the guard before installing the front guard, and loose the screw on the circlip appropriately. After that, align the front guard with the rear one to insert the external buckle on the rear guard into the internal groove on the circlip, then tighten the screw on the circlip.
2. Method for installation of easy-pull-buckle circlip: Normally, the circlip is installed
   with the front guard. Position the decorating ring of the guard before installing the front guard, then align the front guard with the rear one to insert the external buckle on the rear guard into the internal groove of the circlip. After that, lock the guard clip and tighten the screw. (Method for installation of the front guard is as shown in Figure 3. The structure of the circlip is as shown in Figure 4.)

2. Installation on the wall (Figure 5) The fan must be installed on the wall or column vertical to the ground. Note: To prevent the fan from falling, make sure the fixing plate for the wall hook is firmly fixed on the wall where the wall fan is installed.

1. Use two screws to firmly fix the fixing plate for the wall hook to the wall, and make sure the wider end of the groove is upward. Note: Make sure the space between the installation position of fixing plate and the ceiling as well as the adjacent wall is up to a minimum 45cm and 30cm respectively.
2. Lift the wall fan to thoroughly insert the groove on the backside of the wall fan into the wall hook on the fixing plate fixed on the wall.

How to use

THE POVWER STANDARD IS 220-240V-/50Hz

Remote Controller

Control Keys

• Press the key to start the fan and enter the first shift of the normal air type, After the fan is started, press this key again to turn off the fan.
• After the fan is started, press the key repeatedly, the airspeed will be subject to the cyclic change in the sequence from low to high. Meanwhile, the corresponding indicator lights on the panel will flash.
• This key is for the selection of air mode. Press it repeatedly, the air mode will be subject to the cyclic change in the order of “Normal- Natural -Sleep”.Meanwhile, the corresponding indicators on the panel will be on alternately. The features of the air modes are as follows: Normal: The fan supplies a constant wind that was set by the air speed key. The wind is adjustable. It has three levels of low, middle and high.

Instructions for the display of body

Instructions for operation of the body

OSC/SPEED key:
When the fan is working. press this key for 3 to start or stop oscillating. When the fan is working. press this key repeatedly, the fan will work in the second “Low-Medi um-Hi gh” sequence.

Natural:
The fan delivers wind, which simulates the natural wind according to the preset computer program and bring us an easy and natural feeling. The wind is associated with the program. It also has three levels of low, middle and high.

Sleep:
The fan delivers wind according to the preset computer program. The Wind is associated with the program and is suitable when sleeping. It has two levels of low and middle.

• This key serves to start or stop the fan oscillation. To choose one direction, press this key until the fan is in the desired direction when it is oscillating.
• Press this button repeatedly, and the time period for air supply is set between 0.5 and 7.5 hours at a step of 0.5 hours, the corresponding indicator will be on. The fan will be shut down automatically when the time is over.

How to Use the Remote Controller

1. Make sure the infrared led on the front end of the remote controller is in alignment with the display window on the fan body when using the remote controller.
2. The remote controller is available for operation within the range of 5 meters away from the front of the fan body and 30° deviation at the left or right side of the fan body.
3. Keep the receiving window away from direct exposure to the sunshine that may affect the operation effect of the receiver.
4. Please remove the battery for proper treatment if the remote controller is to be left idle for a long time or before the built-in battery falls into decay.

Replacement of Batteries of Remote Controller

The remote controller use two 1.5V 7# batteries. They should be installed as follows:

1. Open the battery cover.
2. Install new batteries, and pay attention to their polarity (+ and-).
3. Put back the battery cover.

Buttons of the Body / Panel indication

• ON/OFF Button
  You can press this key to open/turn off the fan

• MODE Button
  You can press the key “MODE” for the remote control

• OSC SPEED Button
  Press 3 seconds to open/close oscillation. Press this key shortly to change the speed in the sequence from low to high

• TIME Button
  You can press the key “TIME” for the remote control.

Pitching Blowing
Lightly lift or press the head or guard to adjust when you need blowing up or down.

Attention

• Before using, please check if the used voltage is the same as the voltage marked on the fan.
• Do not pull the power plug with a wet hand in order to avoid the risks of a leakage inductance or electric shock.
• Please keep away from high temperature, high moisture, acid or alkali oil, insecticide, curtain, and other easily attracted things.
• Before using, please inspect the supply cord and plug. f the supply cord is damaged, it must be replaced by Midea Customer Service Centre in order to avoid a hazard.
• Do not connect the power until the fan is assembled. Unplug and disconnect the power before moving the fan.
• Never insert fingers, pencils, or any other object through the grille when the fan is running.
• Do not expose infants and the elderly to the strong wind for a long time.

MAINTENANCE METHOD

1. Disconnect fan when removing grilles for cleaning
2. Do not use any grinding tool or solvent that may damage the surface to clean this product. Use a cleanser to clean the product surface before wiping it with a cleaning cloth.
3. It is forbidden to clean the electrical parts (e.g. power switch, motor, etc.) with water or other liquid. Clean the electrical parts only by a clean cloth.
4. It is forbidden to disassemble the product for reconstruction. It is recommended to carry out inspection and cleaning for the product every year so as to extend its service life.

CLEANING

1. Be sure to unplug from the electrical supply source before cleaning.
2. Plastic parts should be cleaned with a soft cloth and moistened with mild soap Thoroughly remove soap film with a dry cloth.

DISPOSAL

Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.

MODEL AND BASIC PARAMETERS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>