Infinity Reference 10001A Mono Subwoofer Amplifier Owner’s Manual

Reference 6001A
Reference 10001 A Amplifiers
Owner’s Manual

WHAT’S IN THE BOX

ACCESSING CONNECTORS AND CONTROL PANEL

1. Slide the panel cover down
2. Remove panel cover

MOUNTING THE AMP

Note: It is recommended that you make all wire connections before permanently mounting the amp.
IMPORTANT: Disconnect the vehicle’s negative(-) battery terminal before beginning the installation.

• Always wear protective eyewear when us·ng tools.
• Choose a state mounting location, away from moisture. Check clearances on both sides of a planned mounting surface. Be sure that screws or wires will not puncture brake lines, fuel lines, or wiring harnesses and that vAre routing will not interfere with the state vehicle operation. Use caution when drilling or cutting in the mounting area.
• Choose a location that provides enough air circulation.
• Do no: mount the amplifier with the heat sink facing downward, as this interferes with cooling.
• Mount the amplifier so that it not be damaged by the feet of backseat passengers or shifting cargo in the trunk.

WIRING FOR POWER AND GROUND

At amplifier:

At ground location:
WIRING FOR INPUT SIGNAL
**Low-level signals

Note: when using low-level signals and remote turn-on lead, set the “TURN- ON MOOE” switch to “REM’ and the “INPUT LEVEL’ switch to ‘LO”.
High-level signals
Note: when using high-level signals, set the ‘TURN-ON MOOE” switch to ·oc· and the “INPUT LEVEL” S\•Atch to ‘Hl1″. H no sound plays, change the ‘1NPUT LEVEL”  witch to “Hl2”.
CONNECTING TWO REFERENCES 10001A AMPLIFIERS FOR EXTRA POWER
To connect two Reference 10001 amplifiers, use an RCA patch cable to connect the “PRIMARY OUT” of the primary amplifier to the “SECONDARY IN” of the second amplifier. Set the Primary/ Secondary switch to “PRIMARY” on the primary amplifier, and to “SECONDARY” on the secondary amplifier.
WIRING FOR AUDIO OUTPUT
One subwoofer (4ohm/2ohm)
Two subwoofers (4ohm)
CONNECTING THE REMOTE BASS CONTROLLER
SETTING GAIN, CROSSOVERS, AND BASS BOOST
Setting the gain
**

| 1. Start with GAIN control set to a minimum, and the crossover control rotated midway.
2. Choose music with substantial bass content.
3. Turn the volume control on your receiver to ¾ of its total output.
4. Ad:ust the GAIN control clockwise, listening carefully to the bass output. If you hear distortion, turn the GAIN control counterclockwise 10 to decrease my gain.
---|---

Selecting the crossover frequency

| Choose the crossover point to suit listening preferences. Tum the dials to the left to ower the crossover point and to the right to raise the crossover point. The exact crossover settings depend on your listening preferences.
---|---

Selecting the subwoofer phase

| Switch the PHASE back and forth to determine which setting provides the most
clean bass output.
---|---

Selecting the bass boost

| Adjust the BASS-BOOST control clockwise or counterclockwise to suit your taste.
---|---

SPECIFICATIONS

| Reference 6001 A| Reference 10001 A
---|---|---
Power output (g) 4 ohms| 350 watts RMS x 1| 600 watts RMS x 1
Power output 0 2 oo hms| 600 watts RMS x 1| 1000 watts RMS
x 1
Frequency response| 10-320 Hz| 10-320 Hz
Crossover frequencies| 32-320 Hz variable.
12 dB/ octave| 32 – 320Hz Variable,
12 dB’ octave
Line-level input sensitivity| 200 mVrms –
2.0 V RMS| 203 mums –
2.0 V MIS
High-level input sensitivity| 2 Vrms – 20V RMS.| 2 Vrms – 20V RMS.
Signal-to-noise ratio| >80 dB| >80 dB
THD-t-N @ rated power| <1%| <1%
Fuse rating| 30 Ax 2| 35Ax3
Operating voltage| 9-16 V| 9-16 V
Dimensions (VV x H x D)| 8-11/16′ x 2-1/16″
x 7-1/8′ (220 mm x
51.3 mm x 180 mm)| 12-5/8″ x 2-1/16′
x 7-1/8″ (320 mm x
51.3 mrn x 180 mm)
Weight| 2.54 kg| 3.58 kg
Recommended wire gauge| 8| 4

TROUBLESHOOTING

No audio and the POWER INDICATOR is off.

• No voltage at BATT+ and/or REM terminals, or bad or no ground =nection. Check voltages at amplifier terminals with VOM.

No audio and PROTECT INDICATOR flashes every 4 seconds.

• DC voltage on ampliiier outpU1. The amplifier may need service; see the enclosed warranty card for service information.

No audio and PROTECT and POWER INDICATORS flash.

• Voltage less than 9V on BATT+ =nection. Check vehicle charging system.

No audio and PROTECT INDICATOR is on.

• The amplifier is overheated. Make sure amplifier cooling is not blocked at the mounting location. Or, there may be a voltage greater than 16V (or less than 8. SV) on the BATT+  connection. Check vehicle charging system.

The amplifier fuse keeps blowing.

• The wiling is connected incorrectly or there is a short circuit. Check wiring connections.

Distorted audio.

• The gain is not set properly. Check to set. Check wires for shorts or grounds. The employer or source unit may be defective.

Distorted audio and PROTECT INDICATOR flashes,

• Short circuit in speaker or wire. Remove speaker leads one at a time to locate shorted speaker or wire, and repa:r.

music lacks dynamics or punch

• Speakers are not connected properly, Check speaker com actions for proper polarity.

Engine noise – whining or clicking-in system when the engine is on.

• The amplifier is picking up alternator noise. First, check the ground com action on the amplifier – loose or improper ground is one of the main causes of noise. Turn down gain.  one RCA audio cable away from power wires. Installing an alternator noise filter on the power line between the battery and alternator might also be necessary.

INFINITY® REFERENCE AMPLIFIERS

Features & Benefits
CATEGORY: Car·Audio-Amplifier
POSITIONING: High -performance car amplifiers

**KEY BENEFITS:

**

• Compact Size
• High and Low-Level Input
• Variable Crossover
• Low Noise and Distortion
• Input Level Control
• Full Onboard Protcc.t1on
• Vernon Mode
  

BASIC FEATURES:

Compact Size

• Infinity Reference amplifiers have been engineered with a corr1pact footprint to fit in mor·e vehicles even if available space 1s rrited.

High and Low-Level Input

• Speaker-level and low-level inputs allow the Infinity Rcferer ce Arp ie~ Series to integrate wrt. h both aftermarket and factory car stereo systems.

Variable Crossover

• like ‘any amp r” ·s ava11ab e at similar prices. the infinity Reference Amplifier Series features variable electronic crossovers circuits allowing for precise system tuning and performance.

Low Noise and Distortion

• The Ir fr try ~cference amplifier Series has been eng·1eered using Balearic.ec Di”‘erent1al inputs to ensure low noise and d starter ever at high output levels. It also makes it far less susceptible to line induces radiated engine noise.

Input Level Control

• When low-level inputs a1·e used, t 11s control acinus the 1n;_i. Jt sens try between 200mVrms and 2.0Vrms. When HGP-level inputs are used, this control ad Just the input sensitivity between 2Vrms and 20Vrms.

HARMAN International LR.DJs tries, Incorporated 8500 Balboa Bou! Revard, Northridge, CA 91329 USA
-.vww.infinityspeakers.com 
© 2019 HARMAN International LR. industries, Incorporated. All rights reserved.
life, it is a trademark of HARMAN lntetoationaJ Industries, Incorporated.
registered in the United States and/or other countries. Features. specifications
and appearance a,e subject to change without notice.

Documents / Resources

| Infinity Reference 10001A Mono Subwoofer Amplifier [pdf] Owner's Manual
Reference 10001A, Mono Subwoofer Amplifier, Reference 10001A Mono Subwoofer Amplifier
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>