legrand WNRCB40 Radiant Wireless Smart Scene Controller with Netatmo Instruction Manual

legrand WNRCB40 Radiant Wireless Smart Scene Controller with Netatmo Instruction Manual

BEFORE YOU START

Review this guide in its entirety. Consult an electrician with any questions or if you are unsure of your abilities.
WARNING: Incorrect installation could result in death, serious injury, and/or damage to your home or devices.
CAUTION: To reduce the risk of injury and/or overheating and damage to other equipment:

• For dry, indoor use only.
• Do not use to power medical equipment – not suitable as a disconnecting means.

YOU MAY NEED

• Phillips-head screwdriver
• Flat blade screwdriver
  You May Also Need:
  Voltage tester, pliers, wire cutter, wire stripper, electrical tape, and wire nut.

INSTALLATION

1. Choose a place to install the device
   This device can be installed on a flat wall surface or in any standard U.S. electrical wall box. It may also be installed over the wall next to a standard U.S. electrical wall box, if used with a multi-gang Legrand radiant wall plate, catalog number beginning with RWP26-XXX.

INSTALLATION (on a wall surface)

1. Use provided double sided stickers to install on a tiled or other smooth surface. Markings on the back of the device indicate location for the stickers.
2. Use provided mounting screws to install on dry wall or uneven surface where the sticker may not work.
   Do not remove label or pull out ground wire as device may not sit flush.

INSTALLATION (in an electrical box) (See Figure A)

1. Turn off power to the box at circuit breaker.
   
   Note: Ensure power is off to all devices in the electrical box. Remove old device from box. Install wire nuts to terminate all the exposed wires that were previously connected to the old device. Ensure complete electrical insulation by securing the wire nuts making sure no bare wire is exposed.

2. Install and secure the device

   • a. Fold the wires into the electrical box, taking care not to pinch a wire.
   • b. Remove label on back of the device to expose ground wire and connect it to the box ground.
   • c. Use included mounting screws to secure the device to the electrical box.

INSTALLATION (NEXT TO AN ELECTRICAL BOX)

1. Break off the tabs on device
   Break off the tabs at the top and bottom of the device using pliers as shown in image (Figure B).
   Mark the location of the device on the wall surface to the left or right of existing device(s) installed in the electrical box by visually aligning it with existing device(s).
   

2. Install and secure the device

   • a. Fold the wires into the electrical box, taking care not to pinch a wire.
   • b. Use double sided stickers to install on tiled or any other smooth surface next to the electrical box.
   • c. Use provided mounting screws if the surface next the electrical box is dry wall or uneven surface where the sticker may not work.
   • d. Install the multi-gang subframe using sub-frame screws provided with the radiant wall plate.
   • e. Snap-on the radiant wall plate.
     If installing with a non-radiant wall plate, skip steps “d” and “e” above and use screws provided with the other wall plate to secure this device.

SETUP

Remove battery insulation tab as shown in the image (see Figure B).

Set Up Your System (connect to your network)

1. Download and launch the Legrand Home + Control app. The app is available on the App Store or on Google Play.
2. Connect your smart device to your home network by following the step by step instructions in the app.
3. Use the app to control your smart device.

Set Up Your System (if network access is not yet available)

1. Press the Gateway EZ button for 5 seconds and let go. The LED will turn solid green.
2. Briefly press one of the buttons on the Scene Controller to activate it. The LED on the screen controller will flash green, then turn off.
3. To complete the installation, briefly press the Gateway EZ button. All LEDs on the products will switch off.
4. Once Network is available: Download and Open the Legrand Home + Control app. Customize your scenes in the Settings/Scenes section. For the most recent instruction sheets or more information on this product, please see this link or scan the QR code: https://www.legrand.us/p/wnrcb40wh
   

GETTING TO KNOW YOUR BATTERY POWERED DEVICE

LED Indicator Light Explanations

Reset To Factory Default (Figure D):
Replace battery upon receiving low battery alert in Home + Control app. Average battery life is 8 years. To replace, remove switch cover and slide battery out. Replace with CR2032 3V battery.
Legrand reserves the right to change specifications without notice.

Replace Battery (Figure D):
Replace battery upon receiving low battery alert in Home + Control app. Average battery life is 8 years. To replace, remove switch cover and slide battery out. Replace with CR2032 3V battery.
Legrand reserves the right to change specifications without notice.

REGULATORY INFORMATION

FCC NOTICE: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the transmitter’s radiating structure(s) and the body of the user or nearby persons.

NOTE: Any changes or modifications to this device that are not expressly approved by the manufacturer will void the warranty and the user’s authority to operate the equipment. Contains FCC ID: 2AU5D-WRCB4
IC NOTICE: This device complies with Industry Canada licenseexempt RSS standards. Operation is subject to the following two conditions: (1) this device may not cause interference; and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
RF EXPOSURE STATEMENT: This equipment meets the SAR evaluation limits given in RSS-102 Issue 5 requirements at the minimum separation distance of 20 cm to the human body. Note: Any changes or modifi cations to this device that are not expressly approved by the manufacturer, will void the warranty and the user’s authority to operate the equipment.
IC: 25764-WRCB4
HVIN: WNRCB4

References

• Patents | Legrand
• radiant Wireless Smart Scene Controller with Netatmo
• Smart Lighting from the radiant Collection ⎸Legrand

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>