Fuzhou Swell Electronic S5021 Weather Station Instruction Manual
- June 5, 2024
- Fuzhou Swell Electronic
Table of Contents
Swell Electronic S5021 Weather Station
Instruction Manual S5021
INSTRUCTION MANUAL
IMPORTANT SAFETY INSTRUCTIONS
Please read this user manual carefully before you use this product.
| CAUTION
THE RISK OF ELECTRIC SHOCK
DOES NOT OPEN|
---|---|---
The lightning flash and arrow head within the triangle is warning sign
alerting you of dangerous voltage inside the product| CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK DO NOT REMOVE THE COVER (OR BACK). NO USER SERVICIABLE
PARIS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL| The exclamation
point within the triangle is a warning sign alerting you of important
instructions accompanying the product.
- Please do not expose the unit to a rainy or moist environment to avoid fire hazards or electric shocks.
- The machine should not receive the water drop or water splashes, on the machine could not lay object filled with liquid, like a vase.
Panel Introduction
1.1 Main Unit
- Time
- WAVE receiving/DST (Daylight Saving Time) icon
- Snooze icon
- Alarm icon
- Date
- Week/Time Zone (EST, CST, MST, PST)
- Indoor temperature and humidity
- Outdoor temperature and humidity
- Channel icon
- Battery compartment(3.AA batteries required, not included).
1.2 Sensor
- Signal indicator
- Wall mount
- Battery compartment(2.AAA batteries required, not included)
- Channel switch among 1 to 3
- Battery cover
Features Introduction
- Time/Month/Day/Week display.
- 12/24 time clock • °C/°F switch
- Two-alarm clocks: AU and AL2.
- WAVE: WWVB.
- Indoor temperature operating range: 14°F-122°F(-10°C-50°C, accuracy t1°C); Outdoor temperature operating range: -31°F-140°F(-35°C-60°C, accuracy ±1°C); If lower than the min temperature range, the screen will show “LL.L”. If higher than the max temperature range, the screen will show “HH.H”.
- Indoor humidity working range: 25%-95%(accuracy ±5%); Outdoor humidity operating range: 25%-95%(accuracy ±5%); If lower than the min humidity range, the screen will show “LL”. If higher than the max humidity range, the screen will show “HIT.
- There are only 3 channels to receive outdoor temperature and humidity.
- The low power indicator of the outdoor sensor
- SNOOZE
- Low power indicator
3. First Use
PAIR THE OUTDOOR REMOTE SENSOR
First of all, both the main unit and outdoor sensor need to be paired. Please
follow the methods to pair them as below.
-
Keep both the main unit and outdoor sensor within a distance of 5-10 feet .
-
Put the batteries into the main unit immediately, slide the switch to CH1 of the outdoor sensor and the sensor should be put into the batteries quickly.
-
After powering on, the main unit will start to pair and keep searching both temperature and humidity from the sensor for the first 3 min. will keep flashing during searching)
-
Both temperature and humidity will show on the screen when pairing successfully. Then will stop flashing and keep solid.
-
From 4th-10th min on, the main unit will keep receiving WAVE. will show on the screen and keep flashing at first.
-
When the signal is detected, the icon will turn to and still keeps flashing. When both time and date are updated, it means WAVE is received successfully. Then it will stop flashing and keep solid.
-
During WAVE receiving, none of the buttons work expect DOWN. If you press the DOWN button, WAVE receiving will stop. Then hold the button for seconds to re-receive WAVE.
Button Description:
-
SNOOZE:
A. Under the normal display, single pressing will not work.
B. Under the normal display, hold it for seconds to set snooze.
C. When the alarm clock goes off, press it to snooze the alarm clock. -
SET:
A. Under the normal display, press it to switch time and alarm. B. Under the normal display, hold it for seconds to set the time. C. When switching to an alarm, hold it for seconds to set an alarm clock. -
UP/TIME ZONE:
A. Under the normal display, press once to switch the time zone.
B. In a time setting, press once or hold it for seconds to increase the number. -
DOWNPC/°F•WAVE:
A. Under the normal display, press it to switch the temperature unit to °C/°F.
B. Under the normal display, hold it for seconds to start and press once to stop wave searching.
C. In a time setting, press once or hold it for seconds to decrease the number. -
ALARM/ON/OFF:
Under the normal display, press once to turn on/off AL1 or AL2 alarm clock. -
Channel:
A. Press once to switch the outdoor temperature and humidity from 1-3 channels and cycle mode.
B. Hold it for seconds to delete and re-register the sensor ID. Then the sensor will receive the outdoor temperature and humidity again.
(Button function display)
Operation:
- After powered on, it will show full screen. Then it turns to a normal display when hearing a beep.
- 6 buttons: SNOOZE SET UP DOWN ALARM CHANNEL.
Default display: AM12:00 on 1ST January 2020; alarm off; Time zone: PST;
Temperatur: °F.
5.1 Time Setting
-
Under the normal display, hold the SET button to enter the time setting mode. The setting order is as below:
A. WWVB: DST ON/OFF–12/24-hour display—hour—, minute—date: month-day display or day-month for choose(MD or DM)—year—month—day—exit, the setting will be saved. ‘ DST: if DST is on, it will automatically adjust to daylight saving time on the second Sunday in March or automatically adjust to winter time on the first Sunday in November.
B. WWVB-OFF: 12/24 hour display—.hour—.minute—.date: month-day display or day- month for choose(MD or DM)—.year—month—.day—.exit, the setting data saved. -
Under the normal display, press the UP button to select four time zones: and press the SET button to confirm the selection. The week display will be returned in 5 seconds without any operation and the selected week will be saved.
-
The number will keep flashing when setting, which means it is able to adjust the time.
-
Press UP or DOWN to adjust the number when setting time.
-
After setting, press the SET button to confirm and save.
-
If there is no operation within 10 seconds, the system automatically saves the setting and the screen will be back to the normal display.
5.2 Alarm Setting
- In time display mode, press the SET button to switch to AL1 or AL2 alarm display: AL1 default to 6:00, AL2 default to 7:00.
- In AL1 mode, hold the SET button for seconds to enter the AL1 setting. The setting order is as follows: AL1 hour—AL1 minute—exit.
- The number will keep flashing when setting, which means it is able to adjust the time.
- Press UP or DOWN to adjust the number when setting the time
- After setting, press the SET button to confirm and save.
- If there is no operation within 10 seconds, the system automatically saves the setting and the screen will be back to the normal display.
- The setting for the AL2 alarm is the same as the one for the AL1 alarm.
5.3 Turn on/off Alarm
Under normal display. Press the ALARM button to switch the alarm clock. The
screen will show the alarm as below: AL1 on-.AL2 on both AL1 and AL2 on-.both
AL1 and AL2 are off.
- When the alarm goes off, press the SNOOZE button to enter the snooze mode. and ” or or ” tr keep flashing, then press any buttons to quit the snoozing.
- The alarm will keep going off for 2 min if there is no operation(default).
- During alarming, AL1/AL2 alarm will keep flashing.
- When alarming or snoozing, WAVE receiving is not available during this time.
- The snooze time is for every 5 minutes by default.
- If both AU and AL2 are set with the alarm time, only AL1 works when the time is up.
- When one of the alarms is going off or snoozing and the second is going to alarm, the first one will stop alarming or snoozing.
- The snoozing will keep working unless you turn it off manually.
- Alarm format (2 minutes):
A. 0-10 seconds: Beep once every second.
B. 11-20 seconds: Quick beep twice every second.
C. After 20 seconds: Extremely quick beep 4 times every second.
5.4 Snooze Time Setting
-
Under the normal display, hold the SNOOZE button for seconds to set snooze time: Min: 3 Min/Max: 20 min. The default setting is 5 min.
(Snooze setting screen)
-
The number will keep flashing when setting, which means it is able to adjust the time.
-
Press UP or DOWN to adjust the number when setting the time
-
After setting, press the SET button to confirm and save.
-
If there is no operation within 10 seconds, the system automatically saves the setting and the screen will be back to the normal display.
5.5 Temperature and Humidity Features:
- Out of range: lower temperature shows “Le, higher temperature shows “HH’
- The indoor temperature is updated every 30 seconds.
- After power-on or reset, the main unit will automatically receive both temperature and humidity from the outdoor sensor. (Fefer to 3. Art Use)
- Under the normal display, press the CHANNEL button to switch the temperature and humidity of each channel. The order: sensor CH1 temperature and humidity-.sensor CH2 temperature and humidity—.sensor CH3 temperature and humidity—.CH1, CH2, CH3 Temperature and humidity cycle display (cycle symbol0 ).
- Under the normal display, hold the CHANNEL button for seconds to clear outdoor temperature and humidity data and will re-receive both temperature and humidity within 3 minutes.
- The cycle only works for the sensor you have now. If there is only one sensor mounted outside it is just one sensor that keeps cycling.
- Under the normal display, press DOWN to switch the temperature unit to°C/°F.
5.6 WAVE Receiving:
- Whether you replace the batteries or reset the unit, all operations are the same as the first use. (Fefer to 3. First Use)
- When receiving WAVE, press DOWN to stop it, and then hold it for seconds to re-receive.
- Automatic WAVE receiving time: every day at 1:00 am, 2:00 am and 3:00 am. If not received at 3:00 am, it will continue at 4;00 am or 5:00 am.
- WAVE receiving will be interrupted when the alarm clock or snoozing is working.
6. The Week Display:
Battery:
A. The main unit requires 3AA batteries.
B. The sensor requires 2AAA batteries.
C. Low battery symbol is displayed when the battery is low.
Note: Batteries must be installed with the correct positive and negative
terminals. Do not mix to use both old and new batteries.
If you have any questions, please feel free to contact us:
SUPPORT@DOVEET.COM Made in China
FCC Statement
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) This device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interfere-ence to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>