ZYXEL NWA220AX-6E 802.11ax WiFi 6E Dual Radio PoE Access Point User Guide
- June 5, 2024
- ZYXEL
Table of Contents
NWA220AX-6E 802.11ax WiFi 6E Dual Radio PoE Access Point
ZYXEL
NETWORK
NWA220AX-6E
802.11ax WiFi 6E Dual Radio PoE Access Point
Quick Start Guide
Hardware Installation
Wait until the LED blink green
Connect the UPLINK port to a router with Internet access. If you are not using PoE, connect the Zyxel Device power socket to an appropriate power source.
Option 1 A Nebula Registration with the App
Use the Zyxel Nebula Mobile app to register the Zyxel Device to the NCC using the QR code.
Download and open the Zyxel Nebula Mobile app. Log in with
your myZyxel account.
Create an organization and site or select an existing site. Scan
the Zyxel Device’s QR code to add it to the site. (You can find
the QR code in its web configurator or on a label on the device
or its box.)
Note: The Zyxel Device will go into cloud management mode
automatically after it is registered to a site.
Option 1 B Nebula Registration with the Web
Use the Zyxel Nebula portal to register the Zyxel Device to the NCC
using the MAC address and serial number.
Follow the steps below to manage the Zyxel Device through
the Zyxel cloud-based network management system.
Note: Make sure the connected router has Internet access.
(Goto the Zyxel Nebula Control Center (NCC) website
(https://nebula.zyxel.com). Click Get Started to sign up for
a myZyxel account and log in.
2 Create an organization and a site (network) in the NCC.
3 Enter the Zyxel Device’s LAN MAC address and serial
number (S/N) (see the label on the device) in the NCC
configuration screen.
Note: The Zyxel Device will go into cloud management
mode automatically after it is registered to a site. See the
NCC User’s Guide for more information about configuring
the Zyxel Device through the NCC.
Option 2 Direct Management
Use the web configuration to direct manage the Zyxel Device.
From a WiFi enabled computer, search for the Zyxel
Device’s default WiFi network name (Zyxel-xxxx, where
xxxx is the last four characters of the MAC address) and
connect to it.
Open your web browser and enter *http//11.11
(setup zyxel.com)” for initial configuration. Enter the
default user name (admin) and password (1234). Click
Login.
Note: If the Zyxel Device cannot connect to the Internet,
use the DHCP-assigned IP address of the Zyxel Device to
access its web configurator. Check the connected router
or DHCP server for the IP address of the Zyxel Device.
From a WiFi enabled computer, search for the Zyxel
Device’s default WiFi network name (Zyxel-xxxx, where
xxxx is the last four characters of the MAC address) and
connect to it.
Open your web browser and enter *http//11.11
(setup zyxel.com)” for initial configuration. Enter the
default user name (admin) and password (1234). Click
Login.
Note: If the Zyxel Device cannot connect to the Internet,
use the DHCP-assigned IP address of the Zyxel Device to
access its web configurator. Check the connected router
or DHCP server for the IP address of the Zyxel Device.
Use an Ethernet cable to connect your computer to the
UPLINK port of the Zyxel Device through a PoE injector
or PoE switch.
Use its DHCP-assigned IP or default static IP address
“http://192.168.12″ to access the web configurator. Make
sure your computer IP address is in the same subnet as
the Zyxel Device’s.
② The wizard appears automatically. Use the wizard to set
up your Zyxel Device.
Note: It takes 1 to 2 minutes to apply your wizard
changes. The LED turns steady blue if you change the
Zyxel Device default settings and the WiFi is on.
③ Use the Zyxel Device’s new wireless settings (SSID and
key) to re-connect to the Zyxel Device’s WiFi network for
Internet access if you change them in the wizard (or log in to
the web configurator when the Zyxel Device is using a
WiFi connection). The LED turns steady green when WiFi
clients connect to the Zyxel Device.
Note : The 1111: (setup.zyxel.com) is for initial setup only. It
is not usable after the Zyxel Device is configured.
Note : Check the Dashboard screen and note down the
Zyxel Device’s IP address in case you need to access its
web configurator again.
Wall / Ceiling Mounting
The mounting kit is for wall or ceiling mounting. You need to
choose how you want to mount your Zyxel Device first.
Wall Mounting: Drill two holes for the screw anchors (A),
62.4 mm apart. Insert the screw anchors into the wall.
Ceiling mounting: Drill two holes for the screw anchors
(A), 62.4 mm or 70.1 mm apart. Insert the screw anchors
into the ceiling
Install two mounting screws through the holes on the
bracket (B) into the plugs/anchors to secure the bracket to
the wall/ceiling. Make sure the screws are snugly and
securely fastened to the wall/ceiling.
After the bracket is attached to the wall/ceiling, slide the
Zyxel Device onto the bracket until it clicks into place.
T-bar Ceiling Mounting
Clips (ACCESSORY – ZZ0105F) are sold separately.
1 Attach two clips to the ceiling grids as shown.
2 Install two screws to secure the bracket to the clips.
3 Slide the Zyxel Device onto the bracket until it clicks into the
place.
Note: Clips (ACCESSORY-ZZO105F) are sold separately.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>