ninebot F25e Kick Scooter Instruction Manual

ninebot F25e Kick Scooter

Welcome

Warning: Always wear a helmet, elbow pads and knee pads when riding.

Packing List

• 3 mm Hex Wrench

• M5 Screw × 5

• Valve Stem Extension

• Battery Charger

• Tire (For F25E)

Assembly

• Unfold the handlebar stem and close the quick-release lever.
  

• Unfold the kickstand.

• Connect the wires inside the handle and the stem. Slide the handlebar onto the stem with the headlight facing forward.
  

• Install the 4 screws in order (two on each side) with the included hex wrench.

Activation

• An inactivated KickScooter will keep beeping when turned on, and its speed is limited to 15 km/h (9.3 mph).

• Scan the QR code to download the Segway-Ninebot app to register or log in.

• Click “Search vehicle” and pair with your KickScooter.
  

• Follow the instructions to watch the Riding Safety.

• Click to activate the KickScooter.

How to Ride

• Power on the KickScooter.

• Stand on the footboard with one foot and push off with the other foot to start gliding.

• Put both feet on the footboard and stand stably. Press the throttle to speed up when you are balanced. Note: For your safety, the motor will not engage until the KickScooter reaches 3 km/h (1.9 mph).

• Slow down by releasing the throttle and squeezing the brake lever. The rear light flashes when braking (not for F20D, F30D or F40D).

• To turn, shift your body and turn the handlebar slightly.

• Put down the kickstand.

Charging

• Charge Port

• Open the charge port cover.
  

• Insert the charge plug.

• Close the charge port cover when finished.

WARNINGS

• DO NOT ride on public roads, motorways, or highways unless the local laws or regulations have exceptions.
  

• DO NOT use a mobile phone or wear earphones when riding the KickScooter.

• EN DO NOT ride up and down stairs or jump over obstacles.

• DO NOT ride the scooter with only one foot or one hand.

• DO NOT overtake.

• Watch your head when passing through doorways.

• DO NOT carry any passengers.
  

• Keep your speed between 3.1–6.2 mph (5–10 km/h) when you ride through speed bumps or other uneven surfaces.

• Avoid contacting obstacles with the tire/wheel.

• DO NOT carry heavy objects on the handlebar.
  

• DO NOT touch the hub motor after riding because it can get hot.

• DO NOT touch the disc brake after riding.

• DO NOT ride the scooter in the rain. DO NOT ride through puddles or other obstacles.

• DO NOT park in the open air or outdoors for a long time.

Folding

• Lift the safety lock and open the quick-release lever.

• Lift the safety lock and open the quick-release lever again, then fold the stem.

• Align and fasten the snap hook and the buckle.

Carrying

• Lift by the stem to carry.

Unfolding

• Disengage the snap hook from the buckle.

• Unfold the handlebar stem and close the quick-release lever.

Adjusting the Disc Brake Cable

• Before adjustment, make sure the scooter is powered off and not charging.

• Loosen: Loosen the screw with a 4 mm hex wrench. Decrease the brake cable and tighten the screw.

• Tighten: Loosen the screw with a 4 mm hex wrench. Increase the brake cable and tighten the screw.

Valve Stem Extension

• Unscrew the valve cap.

• Connect the valve stem extension to the tire valve stem.

• Connect the pump to inflate the tire.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>