CLOSETMAID 4567, 4610 Shelf and Hang Rod Kit Instruction Manual

Shelf & Hang Rod Kit
Instruction Manual

INSTALLATION INSTRUCTIONS

BEFORE BEGINNING

• Please read all instructions carefully.
• Follow all safety precautions (see “SAFETY PRECAUTIONS”).
• Familiarize yourself with all parts (see “CONTENTS”) and check quantities.

What you will need: STOP
FOLLOW INSTRUCTIONS CAREFULLY
Please do not return product to the retail store. For product assistance and warranty information please call Consumer Affairs at 1-800-874-0008.
Manufacturer Warranty
Manufacturer will replace any missing or damaged part due to manufacturer defect. Please have proof of purchase.

SAFETY PRECAUTIONS

WARNING

• This unit contains small parts which could be a choking hazard for small children. Children should always be under adult supervision or serious bodily injury could occur.

• Always unload unit prior to moving the unit. The weight of personal belongings can cause the unit to become unstable and either tip or collapse. Serious bodily injury and / or damage to personal belongings may occur.

• Do not overload unit. If any shelf, top, or bottom of unit bows or bends, it is overloaded. The shelf, top, or bottom could collapse and cause serious bodily injury and / or damage to personal belongings.

• Do not climb or step on the unit. The unit may become unstable and either tip or collapse. Serious bodily injury and / or damage to personal belongings may occur.

• Do not use this unit as a television stand. Serious bodily injury and / or damage to personal belongings may occur.

• Do not mount or attach anything to the sides, rear or front of the unit as this can create a force which can cause the unit to tip. Serious bodily injury and/or damage to personal belongings may occur.

• Unless unit is specifically built for, DO NOT STACK. Only stack units that have been designed for stacking, and only after reading the instructions provided. Stacking of units can cause an unsafe tip-over hazard which may cause serious bodily injury. And / or damage personal property.

• Do not hang this unit on the wall. The product structure is not designed for wall hanging. Serious bodily injury, damage to personal belongings, and / or damage to the
  wall may occur.

• Follow proper safety procedures when using power tools and ladders.

• We recommend you protect your work surface during assembly to prevent scratching or damage to table tops, wood floors, etc.

• All units must be secured individually to wall stud using hardware provided. If wall stud is not accessible, consult your local hardware store for appropriate mounting hardware. Failure to do so may create an unsafe tipping hazard that could lead to serious bodily injury and / or damage to personal belongings.

Serious or fatal injuries can occur from furniture tip-over. To help prevent tip-over:

• Install tip-over restraint provided.
• Unless specifically designed to accommodate, do not set TVs or other heavy objects on top of this product.
• Never allow children to climb or hang on drawers, doors, or shelves.
  Use of tip-over restraints may only reduce, but not eliminate, the risk of tip-over.

CONTENTS

HARDWARE PRODUCT

A Top Shelf x 1
B Inner Hang Rod x 1
C Outer Hang Rod x 1
You will have extra hardware depending on application.

STEP 1 Install side support brackets.

Unit to Unit:

• Position the side support brackets (H1) so that they align with the top and back edges to each base unit. Do not align with the front edge of the trim.
• Secure the side support brackets into place using small screws (H2).

Unit to Wall:

• Position one side support bracket (H1) so that it aligns with the top and back edges of the base unit. Do not align with the front edge of the trim.
• Secure the side support bracket into place using small screws (H2).
• Place one end of the top shelf (A) onto the secured side support, holding the other end level. Mark the position for the other side support bracket (H2) on the open wall.
• Pre-drill the bracket hole locations with a 1/4 in. hole. Insert wall anchors (H4) and secure the side support bracket with long screws (H3).

STEP 2 Secure the back support bracket.

• Place the top shelf onto the side support brackets (H1).
• Center and mark the location of the back support bracket (H5) then remove top shelf.
• Pre-drill the bracket hole locations with a 1/4 in. hole.
• Insert wall anchors (H4) and secure the back support bracket with long screws (H3). Anchors are not required if installing directly into studs.

STEP 3 Secure top shelf.

• Place the top shelf (A) back into position on the side support brackets and secure using small screws (H2).

STEP 4 Install hang rod brackets.

Unit to Unit:

• Position the hang rod brackets (H6) into the desired position (approx. 2 1/8 in. from top edge and 1 1/4 in. from front edge) and secure using small screws (H2).

Unit to Wall:

• Position the hang rod bracket (H6) into the desired position (approx. 2 1/8 in. from top edge and 1 1/4 in. from front edge) and secure using small screws (H2).
• Place the hang rod onto the secured hang rod bracket and make sure it is level. Mark the position of the other hang rod bracket (H6) against the open wall. Pre-drill the bracket hole locations with a 1/4 in. hole. Insert wall anchors (H4) and secure the back support bracket with long screws (H3). Anchors are not required if installing directly into studs.

STEP 5 Secure hang rods.

• Slide the inner hang rod (B) into the outer hang rod (C) ensuring the bottom holes are on the outer edges.
• Inset assembled hang rod (B & C) onto the hang rod brackets (H6) and lock into position.

© 2018 ClosetMaid LLC
Ocala, FL 34471
1-800-874-0008
www.closetmaid.com
01-19064
12/18
Call 1-800-874-0008 for parts and service.
Composez le 1-800-874-0008 pour les pièces et l’entretien. Llame al 1-800-874-0008 para piezas y servicio.
01-19064-CM Shelf and Hang Rod Kit-rev 12-18.indd 9
12/14/18 9:37 AM

References

• Home by AMES | Home by AMES

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>