ninebot D38U Kick Scooter User Manual
- May 15, 2024
- Ninebot
Table of Contents
ninebot D38U Kick Scooter
The pictures shown are for illustration purposes only. The actual product or app interface may vary.
Welcome
Always wear a helmet, elbow pads and knee pads when riding.
Packing List
Accessories
Assembly
- Unfold the handlebar stem and close the quick-release lever.
- Unfold the kickstand.
- Slide the handlebar onto the stem with a headlight facing the front. * Make sure that the wires inside the handle and the stem are connected.
- Install the 4 screws in order (two on each side) with the included hex wrench.
Activation
- An inactivated KickScooter will keep beeping when turned on, and its speed is limited to 9.3 mph (15 km/h).
- Scan the QR code to download the Segway-Ninebot app to register or log in.
- Click “Search vehicle” and pair with your KickScooter.
- Follow the instructions to watch the Riding Safety Video.
- Click to activate the KickScooter.
How to Ride
-
Power on the KickScooter.
-
Stand on the footboard with one foot and push off with the other foot to start gliding.
-
Put both feet on the footboard and stand stably. Press the throttle to speed up when you are balanced. Note: For your safety, the motor will not engage until the KickScooter reaches 1.9 mph (3 km/h).
-
Slow down by releasing the throttle and squeezing the brake lever.
The rear light flashes when braking. -
To turn, shift your body and turn the handlebar slightly.
-
Put down the kickstand.
Charging
Your KickScooter is fully charged when the LED on the charger changes from red (charging) to green (trickle charge).
- Open the charge port cover.
- Insert the charge plug.
- Close the charge port cover when finished.
WARNINGS
- DO NOT ride on public roads, motorways, or highways.
- DO NOT use a mobile phone or wear earphones when
- DO NOT carry any passengers.
DO NOT ride up and down stairs or jump over obstacles
DO NOT ride the scooter in the rain. DO NOT ride through puddles or other obstacles.
DO NOT ride the scooter with only one foot or one hand.
DO NOT overtake
Watch your head when passing through doorways.
Keep your speed between 3.1–6.2 mph (5–10 km/h) when you ride through speed bumps, or other uneven surfaces.
Avoid contacting obstacles with the tire/wheel.
DO NOT carry heavy objects on the handlebar
DO NOT touch the disc brake after riding.
Folding
- Lift the safety lock and open the quick-release lever.
- Lift the safety lock and open the quick-release lever again, then fold the stem.
- Align and fasten the snap hook and the buckle.
Carrying
Unfolding
- Disengage the snap hook from the buckle.
- Fold the stem up, close the quick-release lever.
- Make sure the safety lock is in the locked position before riding!
Valve Stem Extension
- Unscrew the valve cap.
- Connect the valve stem extension to the tire valve stem.
- Connect the pump to inflate the tire.
App Features
Please customize these features via the Segway-Ninebot app.
Cruise Mode
Enable Cruise mode via Segway-Ninebot APP, and it will function when rider presses and holds the throttle for more than 5 seconds, with the buzzer ringing a long beep. (KickScooter can not enter Cruise mode when its speed is slower than 5 km/h (3.1 mph))
Cruising will end if rider squeezes brake lever or re-presses the throttle after releasing it.
If the cruise control function is engaged and activated, releasing the throttle will not reduce speed. please press the throttle to inactivate the cruise control or squeeze brake lever to stop.
The pictures shown are for illustration purposes only. The actual product or app interface may vary.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>