SUPERATV Honda Pioneer 700 4 Tinted Hard Top Instruction Manual
- June 3, 2024
- SUPERATV
Table of Contents
SUPERATV Honda Pioneer 700 4 Tinted Hard Top
Roof Cleaning
- Do not use Rain-X®, Plexus® or any other protector, wax, or polish.
- Do not use window cleaning fluids (Windex, 409, etc) or any solvents (gasoline, denatured alcohol, acetone, etc).
- Never use abrasive cleaners, abrasive pads, or gritty cloths.
- Thoroughly rinse Roof to float off dirt and mud.
- Using a soft cloth, or microfiber cloth, clean Roof with warm water and a gentle detergent. Baby shampoo, rubbing alcohol, or hand washing soap can also be used.
- To prevent water spots, use a chamois to blot Roof dry.
Liability Statement
SuperATV’s® products are designed to best fit user’s ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty provided by SuperATV® and is not recommended. SuperATV’s® products could interfere with other aftermarket accessories. If user has aftermarket products on machine, contact SuperATV® to verify that they will work together.
Although SuperATV® has thousands of satisfied customers, user should be aware that installing lift kits, long travel, or suspension kits, tires, etc. will change the ride of machine and may increase maintenance and part wear. Operating any off-road machine while, or after, consuming alcohol and/or drugs increases risk of bodily harm or death. No warranty or representation is made as to this product’s ability to protect user from severe injury or death. SuperATV® urges operators and occupants to wear a helmet and appropriate riding gear at all times.
By purchasing and installing SuperATV® products, user agrees that should damages occur, SuperATV® will not be held responsible for loss of time, use, labor fees, replacement parts, or freight charges. SuperATV®, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any product purchased from SuperATV®. The total liability of seller to user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the product that gave rise to the claim.
SuperATV® will warranty only parts provided by SuperATV®. Any damage or
problems with OEM housings, bearings, seals, or other manufacturers’ products
will not be covered by SuperATV®. SuperATV® parts and products are not
warrantied if item was not installed properly, misused, or modified.
Installing, adding, modifying, or fabricating any factory or aftermarket
product to your ATV/UTV may violate certain local, state, and federal laws. Be
advised that laws vary depending on town, city, county, state, etc. Use of
certain products on public streets, roads, or highways may be in violation
law. The Buyer is solely and exclusively legally and personally responsible
for any violation of the law by the installation or use of the product. You
must abide by all local, state, and federal laws, including but not limited to
vehicle safety, traffic laws, and ordinances. It is your responsibility to
know the laws and how they apply to you.
The Buyer is responsible to fully understand the capability and limitations of his/her vehicle according to manufacturer specifications, warnings and instructions and agrees to hold SuperATV® harmless from any damage resulting from failure to adhere to such specifications, warnings and/ or instructions. The Buyer is also responsible to obey all applicable federal, state, and local laws and ordinances when operating his/her vehicle while using this product, and the Buyer agrees to hold SuperATV® harmless from any violation thereof.
Parts Description
Installation Instruction
- Cut and install Seal pieces across top of Cage.
- Install Gasket to one side of Front Bracket and Rear Bracket.
- Secure Front and Middle to Front Bracket with hardware shown. Gasket to face plastic.
- Tighten hardware.
- Secure Middle and Rear to Rear Bracket with hardware shown. Gasket to face plastic.
- Tighten hardware.
- Install Front Side Plate – L to Front and Rear with hardware shown; do not tighten.
- Repeat for Front Side Plate – R.
Clamp installation notes
- Place (2) Clamps under Seal and around Cage.
- Secure Front to Clamps with hardware shown; do not tighten.
- Place (3) Clamps under Seal and around Cage.
- Secure Front, Middle, and Rear to Clamps with hardware shown; do not tighten.
- Repeat for opposite side.
- Place (3) Clamps under Seal and around Cage.
- Secure Rear to Clamps with hardware shown; do not tighten.
- Install Side Plate – R to Rear with hardware shown; do not tighten.
- Repeat for Side Plate – L.
- Align Roof to machine and tighten all hardware completely.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>