clabel CT320B Label Printer Installation Guide
- June 5, 2024
- clabel
Table of Contents
clabel CT320B Label Printer
PACKING CHECKLIST
APPEARANCE COMPONENT
Front view
Open the top cover
KEY DESCRIPTION
- Press and hold the power button for 2 seconds to turn the printer on.
- When the power is on, press and hold the power button for 2 seconds to turn the printer off.
- In standby mode, click the power button to enter the setup menu.
- When entering the setup menu, press the power button to return to the previous level page.
- Label sheet: Click OK to walk away from a label sheet to position and adjust it to the start of the next label.
- ontinuous paper: click OK to go 10mm, long press to keep going, release the button to stop going.
- When you enter the Setup menu, click OK to confirm your selection.
- When entering the Setup menu click the Up button to go up and select a setting item.
- Increase the number of prints upwards when entering the offline
When entering the Setup menu click the Down button to go down and select the Setup item.
Press and hold the Power button and OK button at the same time to print the self-test page.
PAPER ROLL LOADING
- Press the top cover open button downward to open the top cover.
- Install the paper roll as shown in the figure below.
- Push the retainer to the left until it snaps the paper roll properly and then push the locking switch back to lock it.
- Pull out part of the paper roll and close the top cover, making sure that both sides of the top cover are closed.
SCREEN INFORMATION
Icon area description
- Bluetooth Indication
- When Bluetooth is not paired, the icon blinks, after Bluetooth is paired the icon is always on.
- External Power Supply Indication
- Always on when the USB port is connected to the power supply, and the icon disappears when the power is disconnected.
- Battery Level Indication
- The battery icon indicates a full charge at 4 cells.
- Displays charging animation while the battery is charging, incrementing frame by frame.
- When the battery icon is flashing, it means the power is low, please charge it.
Text Area Description
Screen Settings
| Options | Parameters | |
|---|---|---|
| Fuitnecmtiosn | OPrffin-ltinineg Print speed |
Dbeisprlainyttehdeatfetemrpcloantefisrmstoinrgedthine nthuempbreinrtoefr,tuemp tpola1t0etienmpuptlastheesectasn Low speed, medium speed, high speed
ASdevtatinncgesd
| |
Print Density| 1~15 gears adjustable
Paper Type| Gap paper, black label paper, continuous paper
Print command| TSPL，ESC
Print Direction| Default, rotate 180°
Memory Printing| On, off
Auto shutdown| 5 minutes, 10 minutes, 15 minutes, 30 minutes, 60 minutes, off
Horizontal Offset| -10mm ~ +10mm
Vertical Offset| -10mm ~ +10mm
Prompt tone
Display Language
| On, off
Chinese，English
Restore factory|
settings| Press the Confirm button to restore the factory settings
InfoOrmthaetrion
| Manufacturer| Shenzhen Dudian Technology Co., Ltd.
Equipment Model| CT320B
Serial number| Display product serial number
Hardware Version| Display the product hardware version number
Firmware Version| Display the product firmware version number s of the
Bluetooth
dTd32e0sB-uXnXXX（eAcuotomatic acquisition of the lastfour digit
Bluetooth Name| a r s iqu de）
Bluetooth Address| Display Bluetooth MAC address
Exc Tip content ture
essive tempera
| Status
Print head temperature is too high, please wait.
---|---
|
Pause printing| Ptoaucosentiinnpureinptriinngti,npglease press the confirmation
button
Top cover not closed| The printer top cover is not closed in place, please
close the cover.
FactLack eof paperave
orey s ettitngs dh.
| The printer paper bin is out of paper, please install the paper roll.
be n r s ore| Printer restores factory settings successfully
Printing in progress| Printing in progress, please wait
Print completion| Print completion
OFTWARE DOWNLOAD
Scan the QR code below with a mobile phone to download “YunPrint”. Please operate the software follwing the software guidance.
Usage precautions
- Install the printer on a stable surface. Do not place the printer in areas exposed to vibration or impact.
- Do not use or store the printer in areas exposed to high temperatures, high humidity, or excessive dust.
- Connect the power adapter to an appropriate grounding outlet. Avoid using the same outlet with large motors or other devices that may cause power supply voltage fluctuations.
- No water or conductive substance (i.e., metal) is allowed into the printer. In case of such a condition, turn off the power immediately.
- Do not allow the printer to start printing when there is no recording paper installed, otherwise the printhead and rubber roller will be damaged.
- Disconnect the DC adapter when the printer is not used for a long time.
- Users shall not disassemble the printer for maintenance or modification.
- Use only the power adapter that comes with the printer.
- To ensure print quality and normal lifetime, use recommended or good quality paper.
- Shut down the printer when connecting or disconnecting interface connectors.
- As the power disconnecting device, the power plug of the adapter should be installed near the equipment and easy to access.
- This product is intended to be used at altitudes not exceeding 5,000 m in tropical
Printer cleaning
The printhead should be cleaned promptly if:
- The print is not clear;
- The vertical column of print is not clear;
- A Grinding noise is heard while feeding the paper;
Cleaning Steps:
- Switch the printer power off, open the cover and remove any paper;
- Allow the printhead to cool if it had just finished printing;
- Using a soft cotton cloth dipped in absolute ethyl alcohol, gently wipe the dust and particles off the thermal printhead surface;
- Only use the printer for printing until the cleaning alcohol evaporates completely and the cover is closed;
Note
- Make sure to turn off the printer before any maintenance.
- Do not touch the printhead surface with the fingers or metallic objects. Do not abrade the printhead, rubber roller, and sensor surface with tweezers or other tools
- Do not use gasoline, acetone, or any other organic solvents for cleaning.
- Only use the printer for printing until the cleaning alcohol evaporates completely.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interferencewill not occur
in a particular installation. If this equipment doescause harmful interference
to radio or television reception, whichcan be determined by turning the
equipment off and on, the user isencouraged to try to correct the interference
by one or more of thefollowing measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different. from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE: This device and its antenna(s) must not be co-located oroperation
in conjunction with any other antenna or transmitter. This device complies
with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation.
RF Exposure Statement
- To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance of 5mm the radiator your body.
- This device and its antenna(s)must not be co-located or operation in conjunction with any other antenna or transmitter.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>