moonki MW-PB265BLT Portable Speaker User Guide

moonki MW-PB265BLT Portable Speaker

DEAR CUSTOMER
In order to achieve the best performance of your product, please read this instruction manual carefully before using, and keep it for future reference.

CAUTION
RISK OF ELECTRIC SHOCK, DO NOT OPEN

• Caution: To reduce the risk of electric shock do not open this device.
  there are no serviceable parts for customers. Please refer any maintenance or repair to qualified personnel

• This sign means the existence of dangerous voltage inside the unit, which states a risk of electric shock.

• This sign means that there are important instructions of operation and handling in the manual that comes with this device.

NOTE
This unit may be submitted for changes in specifications, characteristics and/or operation without prior notice to user, in order to continue improving and developing its technology.

Important Notice

Before Use This Speaker

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all warnings.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings nstall in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus including amplifiers) that produce heat.

9. Only use attachments/accessories specified by the manufacturer

10. Only use attachments/accessories specified by the manufacturer

11. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is injured from a tip-over. d.use caution when moving the cart/apparatus combination to avoid

12. Unplug this apparatus during lightning Storms or when unused for long periods of time.

13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way. Such as power- supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normaly, or has been dropped.

14. Battery usage CAUTION-TO prevent battery leakage which may result in bodily injury. property damage, or damage to the remote control.
    Install all batteries correctly,+ and – as marked on the remote control.
    Do not mix batteries(old and new or carbon and alkaline, etc.)
    Remove batteries when the remote control is not used for a long time.
    Batteries (battery pack or batteries excessive heat such as sunshine, fire, or the like).

15. Apparatus shall not be exposed to dripping or splashing.

16. Do not place any sources of danger on the apparatus (e.g. liquid filled objects, lighted candles ).

17. Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

Warning

• Never remove the casing of this apparatus.
• Never lubricate any part of this apparatus.
• Never place this apparatus on other electrical equipment.
• Never look into the laser beam inside this apparatus.
• Make sure that you always have easy access to the power cord, or adaptor to disconnect the apparatus from the power.

Caution
Use of controls or adjustment or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation.

Your Party Speaker What’s In The Box

Check and identify the contents of your package:

• Speaker
• Remote control
• User manual
• Aux In
• AC Power Cable

FCC Compliance Statement

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part15 of the FCC Rule.
Operation is subject to the following two conditions:

1. this device may not cause namul interference, ana
2. his device must accept any interference received, including interference that may cause undesired operation.

FCC ID: 2A6R4-MVWPB265BLT

Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.

Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This transmitter must not be co-located or operating to conjunction with any other antenna or transmitter.

Overview of the Top control panel

1. Mute Button
2. MIC VOL Control
3. GUITARVOL Control
4. MIC TONE Control
5. MIC ECHO Control
6. AUX Input jack
7. USB Charge
8. Standby Button
9.  Mode Button
10. BT Button
11.  Music Volume Control
12. Guitar Input jack
13.  MIC Input jack
14. TWS Button
15. Voice+ Button
16. Voice 0 Button
17. Voice- Button
18. MIC PRIORITY Button
19. BT Coon
20. Previous Button
21. Play/Pause Button
22. BT Disc
23. Next Button
24. 3D Button
25. Lighting Button
26.  Bass Button
27. Display window
28. TONE Button
29. EQ Button

Overview of the Rear panel

1. AC Power Input jack
2. Power ON/OFF Button

Overview of the remote control

1. Power function key
2. BT function key
3. Volume+ function key
4. Play/Pause function key
5. Previous function key
6. Volume- function key
7. bass function key
8. Mode function key
9. Mute function key
10. Next function key
11. EQ function key

Get started

Caution

• Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation.
• Risk of product damage! Ensure that the power supply voltage corresponds to the voltage printed on the back or the underside of the unit.
• Risk of electric shock! When you unplug the AC power cord, always pull the plug from the socket. Never pull the cord.
• Before you connect the AC power cord, make sure that you have completed all other connections

Prepare The Remote Control

To insert the remote control batteries:

1. Open the battery compartment.
2. insert 2 AAAA batteries with correct polarity (+/-) as indicated.
3. Close the battery compartment.

Please Note:

• If you are not going to use the remote for a long time, remove the batteries.
• DO not use old and new or are rent type o Batteries in combination.
  Batteries contain chemical substances, so they should be disposed of properly.

Turn ON/OFF The Speaker

1. The speaker can work with either connected AC power input (AC mode), or by build-in battery.
2. AC mode, connect the AC power cable provided to a wall socket. The speaker will be powered by power and set the power switch on the rear panel to ON position.
3. Press the POWER button on the top panel or on the remote control to turn it into Standby mode, and press it again to power it on.

Caution:
If you do not use this unit for a while, please switch the “POWER” button to “OFF” status, and disconnect the AC power cable of this unit.

Charging The Internal Battery
The speaker comes with a built-in rechargeable battery, follow the below steps to charge it:

1. Connect the power cable and plug to the wall socket on the rear panel.
2. There is a battery indicator light on the rear panel, there will be a red light when it is being charged.
3. When the battery indicator light on the rear pane turn green, indicates the battery is fully charged, then unplug the power cable to stop charging

Built-in Battery Care

• Your product is powered by a rechargeable battery.
• The battery can be charged and discharged hundreds of times, but will eventually wear out.
• Unplug the charger from the electrical plug and the product when not in use.
• Do not leave a fully charged battery connected to a charger, since overcharging may shorten its lifetime.
• If left unused, a fully charged battery will lose its charge over time.
• leaving the product in hot or cold places, such as in a closed car in the summer and winter conditions, will reduce the capacity and lifetime of the battery.
• Always try to keep your device in a cool, moisture-free environment that’s less than 32°C.
• A product with a hot or cold battery may not work temporarily, even when the battery is fully charged.
• Battery performance is particularly limited in temperatures well below freezing.
• The unit should be fully recharged after using the device each time. This will keep the health of the battery.
• If you plan to store your device for longer than six months, charge the battery for two hours every six months to keep it fresh.

Note: please fully charge the product when it is not going to be used for a long time and charge once a month to keep a longer battery life.

Basic key play operations 

Bluetooth

1. Press the M/MODE button on the Top Control panel or on the remote control to switch to the BLUETOOTH CONNECT mode, (bLUE) will be displayed on the screen.
2. Open the Bluetooth on the external device (must have Bluetooth function), andthe name “MW-PB265BLT” will show on the device, please try to connect it.
3. Once connected, you can hear a small sound from the speaker.
4. You can use the K or key on the Top Control panel to control the tracks of the external device.
   Note: This speaker do not need the password.

TWS Connecting two speakers for True Wireless Stere o sound Optional, requires two speakers

If you have two of these speakers (MW-PB265BLT), you can use them together for a more
immersive audio experience. To pair the two speakers:

1. Place both speakers within Bluetooth range of each other (in the same room).
2. Press the Power Button to turn on each speaker and the speaker will switch to Bluetooth mode automatically.
3. Now short press the TWS Button on one unit, and PAIR” will show on the display window, wait for about 3 seconds and you will hear the tone “LEFT CHANNEL, RIGHT CHANNEL “indicating that the pairing was successful. Now the main speaker shown “bLUE”, the second speaker shown”bLbL” Search for “MW-PB265BLT’ on your device and connect it.
4. Now you can play Bluetooth audio from both speakers in stereo.

Note:

1. To switch back to playing audio on one speaker, press the TWS button on any one device.
   PAOF will show on the display window.

2. You can short press the TWS button on the main unit again to reconnect. “PAIR” will be shown on the display window, wait for about 3 seconds and you will hear the tone “LEFT
   CHANNEL, RIGHT CHANNEL” indicating that the pairing was successful.

3. If the speaker is on the BLUETOOTH(TWS) mode when switching to AUX, you can also enjoy WS function in this mode; But if you disconnect the two speakers in AUX mode, can not reconnect again unless you switch to BLUETOOTH mode to reconnect.

AUX Line In

1. Press the M/MODE button on the Top Control panel or on the remote control to switch to the AUX(Line) mode, (AUH) will be displayed on the screen.
2. Connect this speaker to AUX by inserting the jack and the external device Earphone jack by provided AUX cable;
3. Once connected, turn on your external device’s music
   Caution: Please turn off the unit before connecting AUX cable in order to avoiding unexpected noise.

Connect with Wired Microphone/Guitar

• Insert 6.35mm wired microphone to play with a microphone.
• Insert 6.35mm wired guitar to play with the guitar.
• When playing with the wired microphone/guitar, please push these sliders to adjust the sound volume level of the microphone/guitar.

Microphone:

1. When inserting the wired microphone, push these sliders first to open the microphone volume control or echo volume control of the microphone,
2. you can use the “MIC VOL” slider for volume increase or decrease of the microphone.
3. You can use the “MIC TONE” slider for the Tone increase or decrease of a microphone.
4. You can use the “ECHO” slider for the ECHO increase or decrease of a microphone.

Guitar:

1. When inserting the wired guitar, push the “GT VOL” slider first to open the guitar volume control,
2. You can use the “GT VOL” slider for volume increase or decrease of GUITAR.

Important Notes
While using the microphone, avoid being put the microphone opposite the bass of the Speaker, as they may have Whistler Noisy.
To get the best singing performance, keep the microphone within 5-15cm of the mouth and at a 45-degree angle.
When using the microphone, always pay attention to the battery.
If the battery is low, the indicator light will come on and the performance will progressively become poor.
Caution: Please do not put the microphone directly face to the speaker, it may damage the speaker.

Product Information Specifications

Troubleshooting

warning
Never remove the casing of this speaker.
you encounter problems when using this speaker, check the following points before requesting service.

No power

• Ensure that the AC power plug of the speaker is connected properly.
• Ensure that there is power at the AC outlet.

No sound or poor sound

• Adjust the volume.
• Disconnect the headphones.
• Check that the speakers are connected correctly.
• Check if the stripped speaker wires are clamped.

No response from the speaker

• Disconnect and reconnect the AC power plug, then turn on the speaker again.

Remote control does not work

• Before you press any function button, first select the correct source with the remote control instead of the main unit.
• Reduce the distance between the remote control and the unit.
• Insert the battery with its polarities( +/- signs) aligned as indicated.
• Replace the battery.
• Aim the remote control directly at the sensor on the front of the speaker.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>