teesa TSA0523 CUT PRO Hair clipper Owner’s Manual
- June 5, 2024
- teesa
Table of Contents
teesa TSA0523 CUT PRO Hair clipper Owner's Manual
Thank you for purchasing TEESA appliance. Please read this operation instruction carefully before use, and keep it for future use. Producer does not take responsibility for damages caused by inappropriate handling and use of the product.
SAFETY INSTRUCTIONS
In order to reduce the risk of any injury, follow basic safety precautions applied when using any electrical device, including the following:
-
Read this instruction manual carefully, even if you are familiar with the appliance.
-
Before connecting the device to power supply socket, make sure the voltage indicated on the appliance corresponds to the voltage in the power supply socket.
-
ALWAYS turn off the device and disconnect it from the mains supply:
• if it’s not operating correctly,
• if there’s an uncommon voice when using,
• before disassembling the device,
• before cleaning,
• before servicing. -
When you disconnect the power cord, grasp and pull the plug, not the cord/cable.
-
This appliance may be used by children and by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if they are supervised and guided
by a person who is responsible for their safety in a cautious manner, and all the safety precautions are understood and followed. Children should not play with this device. -
Use only the included AC charger to charge the device.
-
Do not use this appliance if it’s not operating properly or has been dropped into water. Do not attempt to repair this appliance yourself, only authorized and qualified personnel may repair this device. This product has no user serviceable parts.
-
Keep the device and its cord/cable away from heat, water, moisture, sharp edges and any other factor which may damage the appliance or its cord.
-
Do not use the product for purposes/uses different from what displayed in this operating manual.
-
Producer of this product is not responsible for damages caused by inappropriate handling and using of the device.
-
Use only original/authorized accessories.
-
Do not use the appliance in bath or shower.
-
Do not place or store product where it can fall or be pulled onto a tub or sink.
-
Do not reach for a product that has fallen into water. Unplug it from power supply socket immediately.
-
Do not handle the appliance with wet hands.
-
Do not immerse the appliance in water or any other liquids.
-
Product for household use only. Not for commercial use.
-
Clean and store this appliance in accordance to instructions listed in “Cleaning” and “Storage” section.
CHARGING
Notes:
- Make sure the appliance is turned off before connecting it to the power supply.
- It takes about 2 hours to fully charge the appliance what provides about 2 hours of run time.
- Connect one plug of the AC charger to the power supply socket.
- Connect the other plug to the appliance’s power socket.
- When the appliance is charging, charging indicator is on and operating time increases.
- When the appliance is fully charged, charging indicator goes off.
- Disconnect the AC charger from the appliance and power supply socket.
Notes:
- The appliance may become warm during charging/operation. It is a normal behaviour.
- Use the included charging station to charge the appliance. To do this, first connect one plug of AC charger into power supply socket. Then connect the other plug to the charging socket of charging station. Finally, place the appliance into the charging station.
- When the appliance is fully charged, remove the appliance from charging station and disconnect the AC charger from the power supply socket.
INSERTING AND REMOVING COMBS
Notes:
- Make sure that the appliance is turned off when attaching or removing the combs.
- The set includes four guides, each of them having different cutting lengths- 3, 6, 9 and 12 mm.
- Choose the desired comb.
- Attach the comb on the back of the blade and slide it downwards until it locks in place.
- Remove the comb from the blade by pushing it upwards.
OPERATION
- Slide the Power switch upwards to turn on the appliance. Note: If you want to use the appliance with a comb attached, do it before turning on the appliance (see “Inserting and removing combs” section).
- Set the cutting length switch to the desired position. Available cutting lengths are 0,8; 1,05; 1,3; 1,55 and 1,8 mm.
- Start cutting your hair: · when cutting hair with a comb attached, make sure the blade stays close to the skin; · use the appliance without comb attached for more precise trim (for example on the temples).
- When trimming is finished, turn off the appliance by sliding the Power switch downwards.
- If the appliance was used with the comb attached, remove and clean the comb and the whole appliance according to the instructions included in “Cleaning” section.
CLEANING
General:
- Do not immerse the appliance in water.
- Do not clean the blade under running water. Clean it only with the included brush.
- Do not use any abrasives or chemical agents to clean this product.
- Clean only the casing with a soft and slightly damp cloth.
- Clean the appliance after each use. Regular cleaning guarantees better shaving performance.
- Make sure the appliance is turned off and disconnected from power supply.
- Remove the blade by pushing it out of the appliance.
- Use the included brush to clean the blade and the hair chamber.
- To reassemble the blade, first place its lug on the lower ridge of the hair chamber and then push it firmly onto the appliance.
- Clean the combs using the brush or rinse them under running water. Make sure to wipe them dry before refitting.
OILING
Oiling indicator on the display reminds the user to lubricate the blade. It is required to keep the blade in good condition and provide optimal performance. When indicator appears on the display, place 2 or 3 drops of included maintenance oil in between fixed and moving blade.
STORAGE
- Before storing the appliance, make sure it is clean, dry and disconnected from the power supply.
- Store the appliance in a dry, cool place, out of the reach of children.
SPECIFICATION
MAIN FEATURES
4 attached combs (3, 6, 9, 12 mm)
Cord and cordless use LED display with charging indicator, oiling indicator
and operating time
Detachable cutter for easy cleaning
Charging station for convenient charging
TECHNICAL DATA
Power: 3 W
Cutter width: 45 mm
Length settings: 0,8 mm, 1,05 mm, 1,3 mm, 1,55 mm, 1,8 mm
Run time: up to 2 h
Charging time: up to 2 h
Noise level: ≤75 dB
Battery: 3,7 V; 1300 mAh
Power supply:
Input: 100 – 240 V; 50/60 Hz
Output: 5 V; 1 A
In set: AC charger, charging station, 4 combs, cleaning brush, maintenance
oil, user manual
PHYSICAL PARAMETERS
Weight: 251,2 g
Dimensions: 51,5 x 176 x 48,5 mm
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
Made in China for Lechpol Electronics Leszek Sp.k., ul. Garwoliska 1, 08-400 Mitne.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>