addon MFS1S50-H020E-AO Active Optical Cable Instructions
- June 3, 2024
- addon
Table of Contents
- addon MFS1S50-H020E-AO Active Optical Cable
- Features
- Application
- Product Description
- Electrical Characteristics
- Active Optical Cable Specifications
- Electrical Pin-Out Details
- Pin Descriptions
- Block Diagram
- Mechanical Specification
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
addon MFS1S50-H020E-AO Active Optical Cable
Features
- Low latency DSP-free electronics-based CDR
- Multi-data rate up to 56.15 Gb/s per lane
- PAM4 modulation
- Single 3.3 V power supply
- Low power consumption: 3.6W on 200G end with all CDRs enabled
- Up to 20m length
- SFF-8665 compliant
- SFF-8636 compliant I2C management interface
- Operating case temperature: 0◦C to 70◦C
- Hot pluggable
- RoHS/REACH compliant
- TUV-certified
- LSZH, Aqua cable
Application
- IEEE 802.3cd 200GBASE SR4
- IBTA InfiniBand HDR
- Datacenter: servers, switches, storages and NIC adapters
- Proprietary HPC interconnections
Product Description
This is a Mellanox® MFS1S50-H020E compatible 200GBase-AOC QSFP56 to 2xQSFP56
active optical cable that operates over multi-mode fiber with a maximum reach
of 20.0m (65.6ft). At a wavelength of 850nm, it has been programmed, uniquely
serialized, and data-traffic and application tested to ensure it is 100%
compliant and functional. This active optical cable is TAA (Trade Agreements
Act) compliant, and is built to comply with MSA (Multi-Source Agreement)
standards. We stand behind the quality of our products and proudly offer a
limited lifetime warranty.
AddOn’s active optical cables are RoHS compliant and lead-free.
TAA refers to the Trade Agreements Act (19 U.S.C. & 2501-2581), which is intended to foster fair and open international trade. TAA requires that the U.S. Government may acquire only “U.S. – made or designated country end products.”
Absolute Maximum Ratings
| Parameter | Symbol | Min | Typ. | Max. | Unit |
|---|---|---|---|---|---|
| Supply Voltage | Vin | 0 | 4.0 | V | |
| Input Swing | Vin-max | 1500 | mVpp | ||
| Storage Temperature (Ambient) | Tstc | -40 | 85 | °C | |
| Relative Humidity | RH | 5 | 85 | % |
Recommended Operating Specifications
Parameter| | Symbol| Min| Typ.| Max.| Unit|
Notes
---|---|---|---|---|---|---|---
Operating Case Temperature| Top| 0| | 70| °C|
Power Supply Voltage| Vcc| 3.15| 3.30| 3.47| V|
Power Supply Current| 200G End| ICC| | 1100| 1250| mA| 1
100G End| ICC| | 750| | mA| 1
Power Consumption| 200G End| P| | 3.6| 4.0| W| 1
100G End| P| | 2.3| 2.5| W| 1
Note: 1. Per end, all channel CDRs are enabled.
Electrical Characteristics
Parameter| Symbol| Min| Typ| Max| Unit|
Notes
---|---|---|---|---|---|---
Data Rate (Per Channel)| BR| | 26.5625| | GBd| 1
Transmitter
Input Differential Impedance| RIN| | 100| | Ω|
Differential Data Input Swing| VINP-P| 300| | 900| mV|
Receiver
Output Differential Impedance| ROUT| | 100| | Ω|
Differential Data Output Swing| VOUTP-P| 300| 700| 900| mV|
Bit Error Ratio (at 26.5625 GBd)| | | | 2.4×10-4| | 2
Notes:
- Dual data rate of 25.78125 and 28.07618 Gbaud are available upon request.
- Pre-FEC Bit Error Ratio with a PRBS 231 – 1 test pattern over a normal operating temperature range.
Active Optical Cable Specifications
| Parameter | Value | Unit | Note |
|---|---|---|---|
| Cable Diameter | LSZH: Ø3.0 ± 0.15 | mm | |
| Minimum Bend Radius | 30 | mm | Without tension |
| Length Tolerance | +300 / –0 | mm | |
| Cable Jacket | LSZH, Aqua |
Electrical Pin-Out Details
Pin Descriptions
| Pin | Logic | Symbol | Description | Notes |
|---|---|---|---|---|
| 1 | GND | Ground | 1 | |
| 2 | CML-I | Tx2n | Transmitter Inverted Data Input | |
| 3 | CML-I | Tx2p | Transmitter Non-Inverted Data Input | |
| 4 | GND | Ground | 1 | |
| 5 | CML-I | Tx4n | Transmitter Inverted Data Input | |
| 6 | CML-I | Tx4p | Transmitter Non-Inverted Data Input | |
| 7 | GND | Ground | 1 | |
| 8 | LVTTL-I | ModSelL | Module Select | |
| 9 | LVTTL-I | ResetL | Module Reset | |
| 10 | Vcc Rx | +3.3V Power supply receiver | 2 | |
| 11 | LVCMOS-I/O | SCL | 2-wire serial interface clock | |
| 12 | LVCMOS-I/O | SDA | 2-wire serial interface data | |
| 13 | GND | Ground | 1 | |
| 14 | CML-O | Rx3p | Receiver Non-Inverted Data Output | |
| 15 | CML-O | Rx3n | Receiver Inverted Data Output | |
| 16 | GND | Ground | 1 | |
| 17 | CML-O | Rx1p | Receiver Non-Inverted Data Output | |
| 18 | CML-O | Rx1n | Receiver Inverted Data Output | |
| 19 | GND | Ground | 1 | |
| 20 | GND | Ground | 1 | |
| 21 | CML-O | Rx2n | Receiver Inverted Data Output | |
| 22 | CML-O | Rx2p | Receiver Non-Inverted Data Output | |
| 23 | GND | Ground | 1 | |
| 24 | CML-O | Rx4n | Receiver Inverted Data Output | |
| 25 | CML-O | Rx4p | Receiver Non-Inverted Data Output | |
| 26 | GND | Ground | 1 | |
| 27 | LVTTL-O | ModPrsL | Module Present | |
| 28 | LVTTL-O | IntL | Interrupt | |
| 29 | Vcc Tx | +3.3V Power supply transmitter | 2 | |
| 30 | Vcc 1 | +3.3V Power Supply | 2 | |
| 31 | LVTTL-I | LPMode | Low Power Mode | |
| 32 | GND | Ground | 1 | |
| 33 | CML-I | Tx3p | Transmitter Non-Inverted Data Input | |
| 34 | CML-I | Tx3n | Transmitter Inverted Data Input | |
| 35 | GND | Ground | 1 | |
| --- | --- | --- | --- | --- |
| 36 | CML-I | Tx1p | Transmitter Non-Inverted Data Input | |
| 37 | CML-I | Tx1n | Transmitter Inverted Data Input | |
| 38 | GND | Ground | 1 |
Note:
- GND is the symbol for signal and supply (power) common for the QSFP module. All are common within the QSFP module and all module voltages are referenced to this potential unless otherwise noted. Connect these directly to the host board signal-common ground plane.
- Vcc Rx, Vcc1 and Vcc Tx are the receiver and transmitter power supplies and shall be applied concurrently. Vcc Rx, Vcc1 and Vcc Tx may be internally connected within the QSFP transceiver module in any combination. The connector pins are each rated for a maximum current of 500 mA.
Block Diagram
Mechanical Specification
About AddOn Networks
In 1999, AddOn Networks entered the market with a single product. Our founders
fulfilled a severe shortage for compatible, cost-effective optical
transceivers that compete at the same performance levels as leading OEM
manufacturers. Adhering to the idea of redefining service and product quality
not previously had in the fiber optic networking industry, AddOn invested
resources in solution design, production, fulfillment, and global support.
Combining one of the most extensive and stringent testing processes in the
industry, an exceptional free tech support center, and a consistent roll-out
of innovative technologies, AddOn has continually set industry standards of
quality and reliability throughout its history. Reliability is the cornerstone
of any optical fiber network and is in engrained in AddOn’s DNA. It has played
a key role in nurturing the long-term relationships developed over the years
with customers. AddOn remains committed to exceeding industry standards with
certifications from ranging from NEBS Level 3 to ISO 9001:2005 with every new
development while maintaining the signature reliability of its products.
U.S. Headquarters
Email: sales@addonnetworks.com
Telephone: +1 877.292.1701
Fax: 949.266.9273
Europe Headquarters
Email:
salessupportemea@addonnetworks.com
Telephone: +44 1285 842070
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>