addon MC2309130-0xx-25G-AO Mellanox Compatible TAA Compliant 25GBase-CU QSFP28 to 1xSFP28 Direct Attach Cable Owner’s Manual
- June 4, 2024
- addon
Table of Contents
addon MC2309130-0xx-25G-AO Mellanox Compatible TAA Compliant 25GBase-CU
QSFP28 to 1xSFP28 Direct Attach Cable
MC2309130-0xx-25G-AO
Mellanox® Compatible TAA Compliant 25GBase-CU QSFP28 to 1xSFP28 Direct Attach
Cable (Passive Twinax, Up to 5m)
Features
- QSFP28 End : Compliant with QSFP28 MSA specifications
- SFP28 End : Compliant with SFP28 MSA specifications
- 1 independent duplex channels operating at 25Gbps
- AC coupled inputs and outputs
- 100 Ohm differential impedance
- 26AWG to 30AWG Wire Gauge
- All-metal housing for superior EMI performance
- Single power supply 3.3V, low power consumption
- Operating Temperature: 0°C to 70°C
- ROHS Compliant
Applications
- Serial Data Transmission Storage
- Fiber Channel
Product Description
- This is a Mellanox® compatible 25GBase-CU QSFP28 to 1xSFP28 direct attach cable that operates over passive copper with a maximum reach up to 5.0m (16.4ft). It has been programmed, uniquely serialized, and data-traffic and application tested to ensure it is 100% compliant and functional. This direct attach cable is TAA (Trade
- Agreements Act) compliant, and is built to comply with MSA (Multi-Source Agreement) standards. We stand behind the quality of our products and proudly offer a limited lifetime warranty.
- AddOn’s direct attach cables are RoHS compliant and lead free.
- TAA refers to the Trade Agreements Act (19 U.S.C. & 2501-2581), which is intended to foster fair and open international trade. TAA requires that the U.S. Government may acquire only “U.S. – made or designated country end products
Order Information
| Part Number | Description |
|---|---|
| MC2309130-00A-25G-AO | Mellanox® MC2309130-00A-25G Compatible TAA |
Compliant 25GBase-CU QSFP28 to
1xSFP28 Direct Attach Cable (Passive Twinax, 0.5m)
MC2309130-001-25G-AO| Mellanox® MC2309130-001-25G Compatible TAA Compliant 25GBase-CU QSFP28 to
1xSFP28 Direct Attach Cable (Passive Twinax, 1m)
MC2309130-01A-25G-AO| Mellanox® MC2309130-01A-25G Compatible TAA Compliant 25GBase-CU QSFP28 to
1xSFP28 Direct Attach Cable (Passive Twinax, 1.5m)
MC2309130-002-25G-AO| Mellanox® MC2309130-002-25G Compatible TAA Compliant 25GBase-CU QSFP28 to
1xSFP28 Direct Attach Cable (Passive Twinax, 2m)
MC2309130-02A-25G-AO| Mellanox® MC2309130-02A-25G Compatible TAA Compliant 25GBase-CU QSFP28 to
1xSFP28 Direct Attach Cable (Passive Twinax, 2.5m)
MC2309130-003-25G-AO| Mellanox® MC2309130-003-25G Compatible TAA Compliant 25GBase-CU QSFP28 to
1xSFP28 Direct Attach Cable (Passive Twinax, 3m)
MC2309130-004-25G-AO| Mellanox® MC2309130-004-25G Compatible TAA Compliant 25GBase-CU QSFP28 to
1xSFP28 Direct Attach Cable (Passive Twinax, 4m)
MC2309130-005-25G-AO| Mellanox® MC2309130-005-25G Compatible TAA Compliant 25GBase-CU QSFP28 to
1xSFP28 Direct Attach Cable (Passive Twinax, 5m)
Regulatory Compliance
- ESD to the Electrical PINs: compatible with MIL-STD-883E Method 3015.4
- ESD to the LC Receptacle: compatible with IEC 61000-4-3
- EMI/EMC compatible with FCC Part 15 Subpart B Rules, EN55022:2010
- Laser Eye Safety compliant with FDA 21CFR, EN60950-1& EN (IEC) 60825-1,2
- RoHS compliant with EU RoHS 2.0 directive 2015/863/EU
General Specifications
Parameter| Symbol| Min.| Typical| Max.| Unit|
Notes
---|---|---|---|---|---|---
Bit Error Rate| BER| | | − 12
10
| |
Operating Temperature| TC| 0| | 70| ◦ C| 1
Storage Temperature| TSTO| -40| | 85| ◦ C| 2
Input Voltage| VCC| 3.14| 3.3| 3.46| V|
Notes:
- Case temperature
- Ambient temperature
Insertion Loss Level and Wire Gauge
| Cable Length | Wire Gauge | Insertion Loss Level |
|---|---|---|
| 0.5m | 30AWG | CA-25G-N |
| 1m | 30AWG | CA-25G-N |
| 1.5m | 30AWG | CA-25G-N |
| 2m | 30AWG | CA-25G-N |
| 2.5m | 28AWG | CA-25G-N |
| 3m | 28AWG | CA-25G-S |
| 4m | 26AWG | CA-25G-L |
| 5m | 26AWG | CA-25G-L |
Notes:
Cable insertion loss classification standard : IEEE 802.3by 110-10
Weight
| Parameter | Symbol | Typ Max | Unit | Notes |
|---|---|---|---|---|
| 30AWG Product Weight | GD30 | 96 | g/PCS | 1 |
| 28AWG Product Weight | GD28 | 105 | g/PCS | 1 |
| 26AWG Product Weight | GD26 | 110 | g/PCS | 1 |
| 30AWG Cable Weight | GC30 | 32 | g/M | 2 |
| 28AWG Cable Weight | GC28 | 38 | g/M | 2 |
| 26AWG Cable Weight | GC26 | 43 | g/M | 2 |
| SFP28 END Dust CapWeight | GS | 0.80 | g/PCS | |
| QSFP28 END Dust CapWeight | GQ | 1.40 | g/PCS |
Notes:
- The weight of the product.
- The weight of unit length cable (two sticks). For example: the weight of 26AWG cable is: 110+43*(5-1)+0.80+1.40=284.2g
Cable Specifications
Parameter| Symbol| Min| Typ| Max| Unit|
Notes
---|---|---|---|---|---|---
Wire Gauge| | 30| | 26| AWG|
Cable Impedance| Z| 90| 100| 110| Ohm|
Cable Dimension
Serial number| Standard Wire Gauge(AWG)| Cable
diameter OD(mm)| Minimum bendingradius R (mm)
---|---|---|---
1| 30| 4.6| 26
2| 28| 5.0| 28
3| 26| 5.6| 30
Nominal Length
Serial number| Module nominal length L1 (cm)| Tolerance
range ±(cm)
---|---|---
1| L1 ≤ 3| 2
2| 3 < L1 ≤ 4| 4
3| 4 < L1 ≤ 5| 6
Electrical Pin-out Details (QSFP28 END)
Pin Descriptions (QSFP28 END)
| Pin | Symbol | Descriptions | Notes |
|---|---|---|---|
| 1 | GND | Ground | 5 |
| 2 | Tx2n | Transmitter Inverted Data Input, LAN2 | |
| 3 | Tx2p | Transmitter Non-Inverted Data Input, LAN2 | |
| 4 | GND | Ground | 5 |
| 5 | Tx4n | Transmitter Inverted Data Input, LAN4 | |
| 6 | Tx4p | Transmitter Non-Inverted Data Input, LAN4 | |
| 7 | GND | Ground | 5 |
| 8 | ModSelL | Module select pin, the module responds to two-wire | |
| serialcommunication when low level | 1 | ||
| 9 | ResetL | Module Reset | 2 |
| 10 | VCCRX | +3.3V Power Supply Receiver | |
| 11 | SCL | 2-wire serial interface clock | |
| 12 | SDA | 2-wire serial interface data | |
| 13 | GND | Ground | 5 |
| 14 | Rx3p | Receiver Non-Inverted Data Output, LAN3 | |
| 15 | Rx3n | Receiver Inverted Data Output, LAN3 | |
| 16 | GND | Ground | 5 |
| 17 | Rx1p | Receiver Non-Inverted Data Output, LAN1 | |
| 18 | Rx1n | Receiver Inverted Data Output, LAN1 | |
| 19 | GND | Ground | 5 |
| 20 | GND | Ground | 5 |
| 21 | Rx2n | Receiver Inverted Data Output, LAN2 | |
| 22 | Rx2p | Receiver Non-Inverted Data Output, LAN2 | |
| 23 | GND | Ground | 5 |
| 24 | Rx4n | Receiver Inverted Data Output, LAN4 | |
| 25 | Rx4p | Receiver Non-Inverted Data Output, LAN4 | |
| 26 | GND | Ground | 5 |
| 27 | ModPrsL | The module is inserted into the indicate pin and grounded | |
| inthe module. | 3 | ||
| 28 | IntL | Interrupt | 4 |
| 29 | VCCTX | +3.3V Power Supply transmitter | |
| 30 | VCC1 | +3.3V Power Supply | |
| 31 | LPMode | Low Power Mode | 5 |
| 32 | GND | Ground | 5 |
| 33 | Tx3p | Transmitter Non-Inverted Data Input, LAN3 | |
| 34 | Tx3n | Transmitter Inverted Data Input, LAN3 | |
| 35 | GND | Ground | 5 |
| 36 | Tx1p | Transmitter Non-Inverted Data Input, LAN1 | |
| 37 | Tx1n | Transmitter Inverted Data Input, LAN1 | |
| 38 | GND | Ground | 5 |
Notes:
- ModSelL is the input pin. The module responds to 2-wire serial communication commands when it is held low by the host. ModSelL allows multiple QSFP modules to be used on a single 2-wire interface bus. If ModSelL is High, the module will not respond to any 2-wire interface communication from the host. ModSelL has internal pull-up resistors in the module
- The module restart pin, when the low level on the ResetL pin lasts longer than the minimum pulse length, resets the module and restores all user modules to their default state. When performing reset device, the host should ignore all status bits. Until the module reset interrupt is completed, please note that during hot plugging, the module will issue this information to complete the reset interrupt without resetting
- This pin is active high, indicating that the module is running under a low power module. The signal has no effect on the functionality of this product.
- IntL is the output pin, which is the open collector output and must be pulled up to Vcc with a 4.7kΩ-10kΩ resistor on the motherboard. When it is low, it indicates that the module may malfunction. The host uses a 2-wire serial interface to identify the interrupt source
- Circuit ground is internally isolated from chassis ground
Electrical Pin-out Details (SFP28 END)
Pin Descriptions (SFP28 END)
| Pin | Symbol | Descriptions | Notes |
|---|---|---|---|
| 1 | VEET | Transmitter ground (common with receiver ground) | 1 |
| 2 | TX_FAULT | Transmitter failure alarm, not used | |
| 3 | TX_DISABLE | The signal turns off the module transmitter when it is | |
| high oropen, not used. | |||
| 4 | SDA | Data line for serial ID | 2 |
| 5 | SCL | Clock line for serial ID | 2 |
| 6 | MOD_ABS | Module Absent. Grounded within the module | 2 |
| 7 | RS0 | No connection required | |
| 8 | LOS | Loss of Signal indication. Logic 0 indicates normal operation | |
| 9 | RS1 | No connection required | |
| 10 | VEER | Receiver ground (common with transmitter ground) | 1 |
| 11 | VEER | Receiver ground (common with transmitter ground) | 1 |
| 12 | RD- | Receiver Inverted DATA out. AC coupled | |
| 13 | RD+ | Receiver Non-inverted DATA out. AC coupled | |
| 14 | VEER | Receiver ground (common with transmitter ground) | 1 |
| 15 | VCCR | Receiver power supply | |
| 16 | VCCT | Transmitter power supply | |
| 17 | VEET | Transmitter ground (common with receiver ground) | 1 |
| 18 | TD+ | Transmitter Non-Inverted DATA in. AC coupled | |
| 19 | TD- | Transmitter Inverted DATA in. AC coupled | |
| 20 | VEET | Transmitter ground (common with receiver ground) | 1 |
Notes:
- Circuit ground is isolated from chassis ground
- Should Be pulled up with 4.7k – 10k ohm on host board to a voltage between 2V and 3.6V
Mechanical Specifications
ALL DIMENSIONS ARE ±0.2mm UNLESS OTHERWISE SPECIFIED
UNIT: mm
About AddOn Networks
- In 1999, AddOn Networks entered the market with a single product. Our founders fulfilled a severe shortage for compatible, cost-effective optical transceivers that compete at the same performance levels as leading OEM manufacturers. Adhering to the idea of redefining service and product quality not previously had in the fiber optic networking industry, AddOn invested resources in solution design, production, fulfillment, and global support.
- Combining one of the most extensive and stringent testing processes in the industry, an exceptional free tech support center, and a consistent roll-out of innovative technologies, AddOn has continually set industry standards of quality and reliability throughout its history.
- Reliability is the cornerstone of any optical fiber network and is in engrained in AddOn’s DNA. It has played a
key role in nurturing the long-term relationships developed over the years with customers. AddOn remains committed to exceeding industry standards with certifications from ranging from NEBS Level 3 to ISO 9001:2005 with every new development while maintaining the signature reliability of its products.
U.S. Headquarters
Email: sales@addonnetworks.com
Telephone: +1 877.292.1701
Fax: 949.266.9273
Europe Headquarters
Email:
salessupportemea@addonnetworks.com
Telephone: +44 1285 842070
www.addonnetworks.com Phone : 877.292.1701
Rev: 0521 | 9
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>