SMAWAVE SC421 Cat12 Indoor CPE User Guide
- June 6, 2024
- Smawave
Table of Contents
SMAWAVE SC421 Cat12 Indoor CPE User Guide
Introduction
The IDU is a premium indoor LTE CPE, designed for 802.11a/b/ g/n/ac dual band Wi-Fi access. The product provides optimized high through- put data and a wide area coverage network for residential, commercial and enterprise users, supporting multiple services.
Customers enjoy reliable dual-band Wi-Fi AP functions, broadband access and hot-spot Wi-Fi connections with the IDU.
Panel of Device
Packing List
Make sure you have everything you need to properly configure the device.
Configure Hardware
Insert SIM Card
If you want to remove the SIM card, please lightly press the SIM card, the SIM card will pop out. Make sure the CPE is turned off before you insert or remove your SIM card. Otherwise, the CPE and SIM card may be damaged.
Please insert your SIM card (3FF) as following:
How does it Work
The figure is just for reference only, please connect according to your requirements.
Step 1 Connect the supplied power adapter to the CPE.
Step 2 Connect other devices.
- You can connect your computer or classic Switch via Ethernet cable to LAN port.
- You can connect your laptop via Wi-Fi.
When you are using the CPE, you can adjust the position and direction of CPE to get stronger LTE signal, you can judge from the LTE signal LED indicators.
LED Indicators
When set up the IDU, you will see the following LED indicators:
Configure The CPE
Login to the Website
Use a browser to access the management web page to configure and manage the CPE.
The following procedure describes how to use a computer running Windows 7 or above version and Internet Explorer to connect to the CPE webpage.
Step 1 Connect the CPE correctly
Step 2 Start Internet Explorer, go to http://192.168.1.1 in the address
bar, and press Enter.
Step 3 Enter the user name (admin) and password (admin), and click Log
In.
You can connect to the management web page after the password is verified.
Configuration of LTE
Step 1 Connect the CPE correctly.
Step 2 Enter the management website.
Step 3 Choose Settings → Network → LTE Settings.
Step 4 Set the connection mode and scan mode.
The default setting is “auto” connection and full band scanning, if you want to customize your connection to the LTE network, you can set the connection mode as manual, and simply scan a specified band.
Configuration of Wi-Fi
Step 1 Connect the CPE correctly.
Step 2 Enter the management website.
Step 3 Choose Settings → Wi-Fi → WLAN Settings.
Step 4 In the General Settings, set Wi-Fi Enable or enable Wi-Fi with the
Wi-Fi button.
Step 5 In the Setting, change the SSID, such as “LTE-Router”
Step 6 To ensure data security it is recommended that you change the
default Wi-Fi password as soon as you switch-on the device.
Step 7 Click Submit to save the settings.
Troubleshooting
The POWER indicator does not turn on.
- Make sure that the power cable is connected properly and the CPE is powered on.
- Make sure that the power adapter is compatible with the CPE.
Fails to Login to the Web Management Page
- Make sure that the CPE is started.
- Ensure that the CPE is powered on and connected correctly to the computer.
The CPE fails to search for the wireless network.
- Check that the power adapter is connected properly.
- Check that the CPE is placed in an open area that is far away from obstructions, such as concrete or wooden walls.
- Check that the CPE is placed far away from household electrical appliances that generate strong electromagnetic field, such as micro-wave ovens, refrigerators, and satellite dishes.
The power adapter of the CPE is overheated.
- The CPE will be overheated after being used for a long time. There- fore, power off the CPE when you are not using it.
- Check that the CPE is properly ventilated and shielded from direct sunlight.
The parameters are restored to default values.
- If the CPE is powered off unexpectedly while being configured, the parameters will be restored to the default settings.
- After configuring the parameters, download the configuration file to quickly restore the CPE to the desired settings.
If the problem persists please contact the authorized local service provider.
This product has reached the standard of shipment inspection.
Notice
Some features of the product and its accessories described herein rely on the
software installed, capacities and settings of local network, and may not be
activated or may be limited by local network operators or network service
providers, thus the descriptions herein may not exactly match the product or
its accessories you purchase.
We reserves the right to change or modify any information or specifications
contained in this manual without prior notice or obligation.
FCC Regulations:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/ TV technician for help. Changes
or modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. To comply with FCC RF Exposure compliance
requirements, this grant is applicable to only Mobile Configurations. The
antennas used for the transmitter must be installed to provide a separation
distance of at least 20cm from all persons and must not be co-located or
operating in conjunction with any other antenna or transmitter except in
accordance with FCC mult-transmitter product procedure.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
2) this device must accept any interference received, including interference
that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>