teesa TSA8019 stand fan remote control Owner’s Manual

June 5, 2024
teesa

teesa TSA8019 stand fan remote control

teesa TSA8019 stand fan remote control-fig1

PRODUCT OVERVIEW

teesa TSA8019 stand fan remote control-fig2

  1. Front guard
  2. Blade screw
  3. Blade
  4. Rear guard screw
  5. Rear guard
  6. Motor shaft
  7. Tilt angle adjustment screw
  8. Motor unit
  9. Display
  10. Buttons
  11. Fastening screw
  12. Height adjustment nut
  13. Washer
  14. Base

Thank you for purchasing TEESA appliance. Read this instruction manual and keep it for future reference. Producer does not take responsibility for damages caused by inappropriate handling and use of the product.

SAFETY INSTRUCTIONS

In order to reduce the risk of injuries or damages, follow basic safety precautions applied when usingany electrical device, including the following:

  1. Read the entire instruction manual before you start installation and assembly and keep it for future reference. Keep the manual for future reference.
  2. Before connecting the device to power supply socket, make sure the voltage indicated on the device corresponds to the voltage in the power supply socket.
  3. Device for indoor use only.
  4. Do not move the appliance while it is operating.
  5. Clean this device in accordance to instructions listed in Cleaning and maintenance paragraph.
  6. ALWAYS turn off the device and disconnect it from the mains supply:
    • if it’s not operating correctly
    • if there’s an uncommon voice when using
    • before disassembling the device
    • before cleaning
    • when not in use
  7. When you disconnect the power cord of the device, grasp and pull the plug, not the cord / cable.
  8. This appliance may be used by children who are above 8 years old and by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if they are supervised and guided by a person who is responsible for their safety in a cautious manner, and all the safety precautions are understood and followed. Children should not play with this device. Children should not perform cleaning and servicing of the device unsupervised.
  9. Fixed power cable may only be replaced in an authorized service point.
  10. Keep the device and its cord/cable away from heat, water, moisture, sharp edges and any other factor which may damage the appliance or its cord.
  11. Do not place the appliance in water or any liquid; nor handle/use it with wet or moist hands.
  12. Do not use the product for purposes different from displayed in this operating manual.
  13. Do not use unauthorized accessories.
  14. Appliance for home use; do not use it for commercial or industrial purposes. Device for indoor use only.
  15. DO NOT use this device if the cord or the plug is damaged, or the appliance is broken.
  16. Do not attempt to repair this appliance yourself. Only authorized and qualified personnel may repair this device. Never disassemble this device.
  17. Never place the fan near any gas appliances, fire or flammable liquids.
  18. Do not turn on the device if the guard is not mounted properly.
  19. Do not plug the device to power mains before completing the installation.
  20. Never insert fingers, pencils, or any other object through the guard when the fan is running.
  21. Never cover or obstruct the air inlet or outlet to prevent overheating.
  22. Improper installation may result in the risk of fire, electric shock, or injury to persons..

ASSEMBLY

BASE

  1. Unscrew the bolt and washer from the stand.
  2. Insert the stand into the base, attach the washer and tighten the bolt.
  3. Loosen the height adjustment nut, adjust the telescopic tube to the desired height and tighten the nut.
    NOTE: If you cannot see the telescopic tube, it may have slid inside the stand. In such case pull it out from the stand.

BLADE AND GUARDS

  1. Remove the rear guard screw from the motor shaft.
  2. Position the rear guard against the front of the motor housing through the motor shaft. Ensure that the handle at the rear guard is facing up and that all guiding pegs on the motor housing are lined up with the cutouts on the rear guard.
  3. Secure the rear guard with the rear guard screw. Fasten it onto the motor housing by tightening it in a clockwise direction.
  4. Install the blade onto the motor shaft with the cutouts fitted.
  5. Fasten it into place by tightening the blade screw counter-clockwise.
  6. Attach the front guard to the rear guard with the clamps.
  7. Check the correct rotation of the blade.

OPERATION

  1. If you want to adjust the height of the fan you can loosen the height adjustment nut and adjust the telescopic tube to the desired height. Afterwards tighten the nut.
  2. If you want to adjust the tilt angle, loosen the screw underneath the motor housing, set the desired tilt angle and tighten the screw.
  3. Press the POWER button to turn on/off the device.
  4. Keep pressing the SPEED button to switch between three available speed modes.
  5. Press the SWING button to start or stop oscillation.
  6. Keep pressing the TIMER button to set the timer in 1 hour time intervals. After the timer runs out, the fan will automatically turn off.
  7. Keep pressing the MODE button on the remote control to switch between two available work modes:
    • NORMAL: Normal mode of fan operation.
    • SLEEP: Fan gradually decreases and increases speed.

CLEANING AND MAINTENANCE

  • Prior to cleaning, disconnect the device from power mains.
  • Clean this device with soft, slightly damp cloth. Do not use any chemical agents to clean the fan.
  • Dry the fan with a dry cloth after cleaning.

SPECIFICATION

  • FUNCTIONS
    • 3 speed modes
    • 2 work modes: normal,
    • sleep Timer: 1 – 24 h
    • Automatic oscillation: 90°
    • Adjustable height: 116 – 133 cm Adjustable tilt angle
    • Metal blade guard
    • LED display
    • Touch panel
  • TECHNICAL DATA
    • Power: 50 W
    • Grill diameter: 44 cm
    • Blade diameter: 38 cm
    • Power cable length: 1,35 m
    • Power supply: 230 V, 50 Hz
    • In set: remote control, user’s manual

DISPOSAL

Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
Made in China for LECHPOL ELECTRONICS Sp. z o.o. Sp.k., ul. Garwolińska 1, 08-400 Miętne.

WEB

www.teesa.pl

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals