SUPERATV Plow Pro 72 Inch Snow Plow Installation Guide
- June 3, 2024
- SUPERATV
Table of Contents
2753 Michigan Road • Madison, Indiana 47250 •
855-743-3427
INSTALLATION INSTRUCTIONS
Snow Plow Mount: for Polaris Ranger® XP 1000
SPK-P-RAN1KXP-001 SuperATV Bumper installation
-
Install Mount to machine with hardware shown. Tighten hardware.
-
Install Frame Brackets to Plow Frame as shown with hardware shown.
-
Tighten hardware.
-
Join Plow Frame to Mount with hardware shown.
SPK-P-RAN1KXP Stock Bumper installation
-
Remove Pin from Mount and place Latch in open position.
-
Repeat for opposite side.
-
Place Mount around Frame, close each Latch, and secure with Pins.
-
Join Plow Frame to Mount with hardware shown.
-
Tighten hardware.
Liability Statement
SuperATV’s® products are designed to best fit user’s ATV/UTV under stock
conditions. Adding, modifying, or fabricating any factory or aftermarket parts
will void any warranty provided by SuperATV® and is not recommended.
SuperATV’s® products could interfere with other aftermarket accessories. If
user has aftermarket products on machine, contact SuperATV® to verify that
they will work together.
Although SuperATV® has thousands of satisfied customers, user should be aware
that installing lift kits, long travel, or suspension kits, tires, etc. will
change the ride of machine and may increase maintenance and part wear.
Operating any off-road machine while, or after, consuming alcohol and/or drugs
increases risk of bodily harm or death. No warranty or representation is made
as to this product’s ability to protect user from severe injury or death.
SuperATV® urges operators and occupants to wear a helmet and appropriate
riding gear at all times.
By purchasing and installing SuperATV® products, user agrees that should
damages occur, SuperATV® will not be held responsible for loss of time, use,
labor fees, replacement parts, or freight charges. SuperATV®, nor any 3rd
party, will not be held responsible for any direct, indirect, incidental,
special, or consequential damages that result from any product purchased from
SuperATV®. The total liability of seller to user for all damages, losses, and
causes of action, if any, shall not exceed the total purchase price paid for
the product that gave rise to the claim.
SuperATV® will warranty only parts provided by SuperATV®. Any damage or
problems with OEM housings, bearings, seals, or other manufacturers’ products
will not be covered by SuperATV®. SuperATV® parts and products are not
warrantied if item was not installed properly, misused, or modified.
Installing, adding, modifying, or fabricating any factory or aftermarket
product to your ATV/UTV may violate certain local, state, and federal laws. Be
advised that laws vary depending on town, city, county, state, etc. Use of
certain products on public streets, roads, or highways may be in violation
law. The Buyer is solely and exclusively legally and personally responsible
for any violation of the law by the installation or use of the product. You
must abide by all local, state, and federal laws, including but not limited to
vehicle safety, traffic laws, and ordinances. It is your responsibility to
know the laws and how they apply to you.
The Buyer is responsible to fully understand the capability and limitations of
his/her vehicle according to manufacturer specifications, warnings and
instructions and agrees to hold SuperATV® harmless from any damage resulting
from failure to adhere to such specifications, warnings and/ or instructions.
The Buyer is also responsible to obey all applicable federal, state, and local
laws and ordinances when operating his/her vehicle while using this product,
and the Buyer agrees to hold SuperATV® harmless from any violation thereof.
Do not discard packaging until product has been successfully installed.
- Adjust Skid Pads after Blade, Snow Plow Mount, and Snow Plow Frame are installed to machine.
- Blade height will depend on what type of surface is to be plowed.
Notes:
- To reduce icing, allow Blade to reach same temperature as outdoors before beginning.
- Except for when pivoting Blade, always place Blade on ground before exiting vehicle.
- To avoid damaging Blade, do not plow over pipes, roots, curbs, or other large objects.
- Treating Blade with automotive type paste wax will make snow easier to move off Blade. – Inspect Blade for loose, worn, or damaged components before plowing. Correct any issues.
- Clean Blade after each use and before storing long term.
- Use touch up paint, or a light coat of oil or grease, on any bare metal.
- Lubricate all pivot points before each seasons use.
- Store Blade away from weather and in a dry area after each use.
Do not discard packaging until product has been successfully installed.
Plow Frame
-
Install Plow Frame to Blade with hardware shown. Tighten hardware.
-
Install Eye Bolts and Adjustment Blocks to Plow Frame with hardware shown.
-
Hook Plow Springs into Eye Bolts.
-
Do not tighten hardware.
Adjustment Block
- *Adjustment Blocks can be rotated to offer more adjustability. See page 5.
- All machines are different and orientation may vary.
- Secure Plow Springs to Blade.
- Tighten Nuts on Eye Bolts until desired Plow Spring tension is achieved.
Need help with your installation?
| sales@superatv.com| |
www.superatv.com
---|---|---|---
| 1-855-743-3427| | 8:00am – 8:00pm EST
M-Th
8:00am – 7:00pm EST Friday
9:00am – 2:00pm EST Saturday
Read instructions and view illustrations before beginning.
Thank You For Choosing
© 2022 SuperATV.com
® . All Rights Reserved.
IN-SPF-U-001 1/18/2022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>