rogerseller 3606014501 Tonic Up Wall Mixer and Basin Outlet Instruction Manual
- June 5, 2024
- rogerseller
Table of Contents
rogerseller 3606014501 Tonic Up Wall Mixer and Basin Outlet
Peg-up Mixer
Peg-down Mixer
Installation
-
Step
It is recommended to install in-line filters to ensure a cleaner supply of water to the mixer tap. -
Step
During installation and testing make sure the mixer is in the closed position and the cover, wall plates, handle and spout are removed to prevent damage. Parts damaged during installation wont be covered by warranty -
Step
When mounting the mixer to the wall frame, ensure that the set-out distance of 48-72mm, from the wall frame to the front of the finished wall will be achieved.
Note: Sheeting and tile thickness variation may affect the minimum wall set- out distance. -
Step
Connect water supply to the inlets as shown in the adjacent diagram. When connecting, USE UNION CONNECTORS OR BRAZED JOINTS CONSTRUCTED AWAY FROM THE TAP. Brazed joints ie. Heat, made at the inlets and outlets will result in damage to the ceramic cartridge and void the warranty. -
Step
The mixer must be installed in the horizontal position with the spout to the left to ensure correct handle operation. -
Step
Do not high pressure test the supply system with the outlet blocked and the tap open, as this may damage the ceramic cartridge. -
Step
To complete the installation, screw on the cover and spout. Then carefully guide the cover plate over the spout and cover and press the wall plate firmly against the wall. Fit the handle to the cartridge, securing it with the screw, and push in the button. -
Step
Prior to introducing the mains supply, open
the lever handle in the mixed position, midway between full hot and full cold. Remove the concealed aerator from the spout with the key provided. Then introduce the mains water to flush the supply lines. Reinstall the aerator.
Specification
Specifications
It is a requirement of state plumbing codes that licensed plumbers carry out all tapware installations. All installations must comply with the relevant requirements of AS/NZS3500 and local plumbing codes.
Pressure
Maximum Hydrostatic Pressure – 1000kpa
Recommended Maximum Hydrostatic Pressure – 500 kpa. (AS/NZS 3500)
Recommended Minimum Hydrostatic Pressure – 150 kpa.
Maximum Hydrostatic Pressure may be exceeded under test conditions only in accordance with AS/NZS 3500. Where hydrostatic pressure exceeds the maximum stated above, pressure limiting valves must be installed or warranty will be void.
Temperature
Maximum Water Temperature – 80°C
For optimum performance, Hot and Cold inlet water pressure should be equal.
Care and Maintenance
[1] Product should be inspected for surface damage prior to installation. [2] Cleaning and handling of all finishes must be performed carefully. [3] Clean products using a soft cloth with warm soapy water only. [4] Never use harsh detergents or abrasive cleaners as these will damage the product. [5] Water marks can be removed from Matt Finishes with an application of a carnauba wax based non-abrasive polish on a microfibre cloth. [6] Do not use undue pressure when cleaning and wipe
in one direction only. [7] Contact with harsh chemicals such as hair dye, hair bleach etc will result in damage to the finish. [8] Tapware should never be installed using acetone silicones. [9] Avoid the use of wax based furniture creams as this can result in a build up of deposits which will detract from the appearance. [10] Damage to finishes arising from improper installation or post installation use or failure to observe the above care and cleaning instructions will void all warranty agreements.
Warranty
Rogerseller tapware, bathroom fittings and sanitaryware are covered by a five (5) year warranty from date of purchase.
For full terms and conditions please refer to rogerseller.com.au
Dimensions are approximate. Information in this installation instruction is representative of the product available at the time of printing. Due to our policy of continuous product development, the design and specifications depicted are subject to change without notice. Please confirm all particulars with your client advisor prior to purchase.