rogerseller 3606003601 Arq Sink Mixer Installation Guide

rogerseller 3606003601 Arq Sink Mixer

Product Information

The product is a sink mixer by Arq, manufactured by Rogerseller. It is designed for installation in sinks and complies with State Plumbing Codes and the relevant requirements of AS/NZS 3500 and local plumbing codes.

The product has the following specifications:

• Maximum Hydrostatic Pressure: 1000kpa (under test conditions)
• Recommended Maximum Hydrostatic Pressure: 500kpa (AS/NZS 3500)
• Recommended Minimum Hydrostatic Pressure: 150kpa

The sink mixer is available in 5 finishes and includes components such as a steel washer, base washer, base ring, copper tails, lock screw, riser, aerator key, and aerator insert. The product code for the chrome finish variant is Arq by Rogerseller Sink Mixer 3606003601.

Product Usage Instructions

1. Position the steel washer onto the threaded sleeve under the basin/bench. Ensure that the copper tails are facing toward the front so that the lever handle points toward the user.
2. Tighten the lock screw onto the threaded sleeve to secure the mixer onto the sink.
3. Connect the flexible hoses to the copper tails and tighten them.
4. Connect the flexible hoses to the main water supply lines, ensuring that the hot water hose is connected to the hot water supply.
5. It is recommended to install stop taps to ensure a cleaner flow of water to the mixer.
6. Prior to introducing the mains water supply, open the lever handle to the mixed position (midway between full hot and full cold).
7. Use the provided tools to remove the aerator from the end of the spout.
8. Introduce the mains water to flush the supply lines.
9. Reinstall the aerator and ensure it is securely in place.

For more information and detailed instructions, please visit rogerseller.com.au.

Specifications

It is a requirement of State Plumbing Codes that licensed plumbers carry out all tapware installations. All installations should comply with the relevant requirements of AS/NZS 3500 and local plumbing codes.

Pressure:

1. Maximum Hydrostatic Pressure: 1000kpa. This pressure may be exceeded only under test conditions as per AS/NZS 3500. Where hydrostatic pressure exceeds the maximum stated above, pressure-limiting valves should be installed.
2. Recommended Maximum Hydrostatic Pressure: 500kpa (AS/NZS 3500). [3] Recommended Minimum Hydrostatic Pressure: 150kpa

Temperature:
Maximum Water Temperature: 80° C. For optimum performance, hot and cold inlet water pressure should be equal.

Care and Maintenance

1. The product should be inspected for surface damage prior to installation.
2. Cleaning and handling of all finishes must be performed carefully.
3. Clean products using a soft cloth with warm soapy water only.
4. Never use harsh detergents or abrasive cleaners as these will damage the product.
5. Watermarks can be removed from Matt Finishes with an application of a carnauba wax-based non-abrasive polish on a microfibre cloth.
6. Do not use undue pressure when cleaning and wipe in one direction only.
7. Contact with harsh chemicals such as hair dye, hair bleach, etc with result in damage to the finish.
8. Tapware should never be installed using acetone silicones.
9. Avoid the use of wax-based furniture creams as this can result in a build-up of deposits which will detract from the appearance.
10. Rose Copper: A protective lacquer has been applied to this finish. This is required to maintain the stability of this finish and will be damaged if the above care and cleaning instructions are not followed.
11. Damage to finishes arising from improper installation or post-installation use or failure to observe the above care and cleaning instructions will void all warranty agreements.

Arq by Rogerseller Sink Mixer

• 3606003601 — chrome
• 5 finishes available

Installation Instructions

1. (Under the basin/bench) Position the steel washer onto the threaded sleeve. The copper tails should be towards the front so that the lever handle points toward the user. Lock the mixer onto the sink by tightening the lock screw onto the threaded sleeve.
2. Connect the flexible hoses to the copper tails and tighten them. Connect the flexible hoses to the main water supply lines, making sure the hot water is connected to the hot water hose.
3. The installation of stop taps is recommended to ensure a cleaner flow of water to the mixer.
4. Prior to introducing the mains water supply, open the lever handle in the mixed position, midway between full hot and full cold. Using the tools provided remove the aerator from the end of the spout. Then introduce the mains water to flush the supply lines.
5. Reinstall the aerator. See notes below.

rogerseller.com.au.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>