inventor FS403W 50W Stand Fan 40cm Diameter User Manual
- June 5, 2024
- inventor
Table of Contents
FS403W 50W Stand Fan 40cm Diameter
User Manual
CAUTION
For safe operation please read and follow the below instructions carefully.
WARNING
-
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent, or a similarly qualified person in order to avoid a hazard.
-
To avoid the risk of electrical shock, do not immerse the unit, cord, or plug in water or any other liquids.
-
This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. -
When the appliance is not operating, and, prior to cleaning, please unplug from the power socket.
-
When assembling the fan, make sure that the protective fan grill covers are properly installed.
-
After the fan assembly, do not remove the rotor blade guard.
-
Do not disassemble the rotor blade guard to clean the rotor blades.
-
Use a slightly damp cloth to clean the fan enclosure and rotor blade.
-
Do not allow any water or other liquid to enter the motor housing.
-
Do not dispose of this product as unsorted municipal waste. This appliance requires special treatment for disposal. It is prohibited to dispose of this appliance in domestic household waste. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.
To return your used device, contact the retailer, it is possible they may dispose of it at a recycling facility.
RULES FOR SAFE OPERATION
- While the fan is operating, no sharp objects, such as pencils, should be inserted through the protective grill. Be extra cautious when handling and be certain no fingers penetrate beyond the protective grill area, this should be strictly avoided at all times.
- Be certain that the fan is disconnected when repositioning from one location to another.
- Be certain that the fan is on a stable surface while operating, to avoid accidental tipping.
- Be extra cautious when operating near a window as rain may cause electric shock.
- This device is intended for domestic use only.
INSTALLATION INSTRUCTIONS
■ Name of components
Considerate Hint: Remove the right-angle bolt from the pole before
performing the installation.
Note: The figures in this manual are only for explanatory purposes. In
case of discrepancies between the illustrations and the actual product, please
refer to the product that you purchased.
Pole Installation
- Remove the tightened knobs from the upper and lower pole.
- Align the poles using as guide the holes in the components. Push downward the upper pole into the hole position.
- Lock and secure the position by tightening the knobs.
- Insert the lower pole into the chassis and tighten the right-angle bolt
Tip: The right-angle bolt may be placed already under the chassis. Remove it before the installation.
GRILL & FAN BLADE ASSEMBLY
- Align the front grill with the rear grill as illustrated.
- Press the joints sequentially with both hands to secure the correct position of the grills.
- Fasten the front grill and the rear grill by the grill clip and then tighten the fan grill locking screw and nut.
Front and Rear Guard Installation
OPERATION INSTRUCTIONS
I. Tilt Adjustment
To adjust the tilt of the airflow upwards or downwards, push the motor housing
lightly to the desired direction.
II. Height adjustment
To adjust the height of the fan, loosen the tighten knob by turning it
counterclockwise, and carefully add or remove the lower pole. Remember to
always secure the position by placing the knob back.
III. Speed adjustment
There are 3 speeds available. To adjust the fan speed, rotate the knob located
on the back of the motor housing. (1=low/2=medium/3=high speed)
IV. Oscillation adjustment
To adjust the oscillation press the on/off button located on the left side of
the motor housing.
MAINTENANCE INSTRUCTION
This fan requires limited maintenance. Do not attempt to fix it on your own. Always refer to qualified personnel if any service is required.
- Prior to cleaning and assembling, the fan must be unplugged.
- To ensure adequate air circulation to the fan’s motor, vents at the rear of the fan motor should be free of dust at all times. Do not disassemble the fan in order to remove the dust.
- The exterior parts of the device may be wiped with a soft and damp (with a mild detergent) cloth.
- The use of any abrasive detergent or solvents, gasoline, or paint thinner for cleaning purposes should be avoided as this may result in damaging the surface of the fan.
- Water or any other liquids in the motor housing or interior parts of the fan must be avoided at all times.
CLEANING
- Prior to performing any cleaning, the device must be unplugged.
- All plastic parts of the device should be cleaned with a soft moist cloth and with mild soap. Thoroughly clean any soap excess with a dry cloth.
All the pictures in the manual are for explanatory purposes only. The actual
shape of the unit you purchased may be slightly different, but the operations
and functions are the same.
The company may not be held responsible for any misprinted information. The
design and the specifications of the product for reasons, such as product
improvement, are subject to change without any prior notice.
Please consult with the manufacturer at +30 211 300 3300 or with the Sales
agency for further details. Any future updates to the manual will be uploaded
to the service website, and it is advised to always check for the latest
version.
Scan here to download the latest version of this manual.
https://www.inventorappliances.com/manuals
STEP 2
Fill in the obligatory fields as requested in the “Owner’s details” and
“Unit’s details”:
STEP 3
Click SEND button at the end of the submission form:
STEP 4
Wait for the confirmation email you will receive at the email address you have
filled once the warranty submission has been completed a confirmation message
will be sent to your email in – please also check your spam folder.
STEP 5
The inventor warranty is now valid!
Manufacturer: INVENTOR A.G. S.A.
24th km National Road Athens – Lamia
2 Thoukididou Str., Ag.Stefanos, 14565
Tel.: +30 211 300 3300,
Fax: +30 211 300 3333
– www.inventor.ac
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>