SENECA UL94-V0 Gateway Radio Instruction Manual
- June 5, 2024
- SENECA
Table of Contents
SENECA UL94-V0 Gateway Radio Instruction Manual
PRELIMINARY WARNINGS
The word WARNING preceded by the symbol **indicates conditions or
actions that put the user’s safety at risk.
The word ATTENTION preceded by the symbol **indicates conditions or
actions that might damage the
instrument or the connected equipment. The warranty shall become null and void
in the event of improper use or tampering with the module or devices supplied
by the manufacturer as necessary for its correct operation, and if the
instructions contained in this manual are not followed.
WARNING: The full content of this manual must be read before any operation. The module must only be used by qualified electricians. Specific documentation is available via QR-CODE shown on page 1.
The module must be repaired and damaged parts replaced by the Manufacturer. The product is sensitive to electrostatic discharges. Take appropriate measures during any operation.
Electrical and electronic waste disposal (applicable in the European Union and other countries with recycling). The symbol on the product or its packaging shows the product must be surrendered to a collection centre authorized to recycle electrical and electronic waste.
DOCUMENTATION R-COMM
ENECA s.r.l.; Via Austria, 26 – 35127 – PADOVA – ITALY; Tel. +39.049.8705359 –
Fax +39.049.8706287
CONTACT INFORMATION
Technical support:support@seneca.it
Product information: sales@seneca.it
This document is the property of SENECA srl. Copies and reproduction are
prohibited unless authorised.
The content of this document corresponds to the described products and
technologies.
Stated data may be modified or supplemented for technical and/or sales
purposes.
MODULE LAYOUT
Weight: 80 g;
Enclosure: UL94-V0 self-extinguishing PC/ABS material, black. 95mm
SIGNALS VIA LED ON FRONT PANEL
| LED | STATUS | LED meaning |
|---|
| On| Signal level reporting
Flashing| Modem not correctly adjusted
NET| On| Modem adjusted on 4G network
Flashing| Modem adjusted on 2G or 3G network
Off| Modem off or not adjusted
DATA| On| Data connection enabled and correctly adjusted
Flashing| Data connection enabled but in error
Off| Data connection disabled
GPS| On| GPS signal present
Off| GPS signal absent
BAT| On| Battery connected and working properly
Flashing| Low or faulty battery
Off| Battery not in use (UPS not active)
PWR| On| Module powered / successful connection
Off| Module not powered / instrument not connected
TECHNICAL SPECIFICATIONS
CERTIFICATIONS|
https://www.seneca.it/products/r-comm/doc/CE_declaration
---|---
POWER SUPPLY| Through connection with the main module
BACKUP BATTERY (R-COMM-B-4GWW ONLY)| Nickel battery AA dimension
1250mAh; 3.6V
ENVIRONMENTAL CONDI- TIONS| Temperature: -25°C ÷ +65°C Humidity: 30%
÷ 90% non-condensing Storage temperature: -30 °C ÷ + 85 °C Protection rating:
IP20
ASSEMBLY| DIN rail 35 mm IEC EN60715 or wall with screws
CONNECTIONS| 1 SIM-CARD slot
1 SMA connector for GPS antenna
1 SMA connector for 4G/LTE antenna
4G MODEM FREQUENCIES| Global coverage Model 4G/LTE
LTE-FDD: B1/B2/B3/B4/B5/B7/B8/B12/B13/B18/ B19/B20/B25/B26/B28 LTE-TDD:
B38/B39/B40/ B41
WCDMA: B1/B2/B4/B5/B6/B8/B19/GSM: B2/B3/B5/B
OUTPUT POWER| GSM900: 32.75dBm, DCS1800: 29.07dBm, WCDMC: 23.13dBm,
23.27 dBm, LTE: 23.1dBm, 23.2dBm, 21.7dBm, 23.19dBm, 23.14dBm, 23.7dBm,
23.39dBm.
GNSS| GPS / GLONASS / BeiDou (compass) / Galileo / QZSS
SIM CARD SLOT| Push-push type for mini SIM card 15 X 25 mm
N.B.: To purchase the “GPS antenna” accessory, access the website www.seneca.it and go to the product page.
UPS BUTTON OFF (R-COMM-B-4GWW ONLY)
Button used to switch the UPS off:
The button is located on the underside of the instrument.
To shut down the UPS of the device, simply press the OFF button, in doing so
the power supplied by the battery pack for the UPS will be disabled.
To switch off the R-PASS main module, it is necessary to disconnect the power
cables from the terminals.
CONNECTION TO THE MAIN MODULE
Installation:
To connect the R-COMM accessory module to the R-PASS main module, position the
instrument on the DIN rail as shown in the procedure below, then slide the
module until it is fully engaged with the side connector.
After the correct connection, the PWR led turns on to show the power supply.
CAUTION
The connection of the R-COMM accessory module must be made with the R-PASS
main module turned off.
N.B.: For an ideal operation of the module, the use of a DIN rail clamp is recommended.
INSTALLATION ON DIN-IEC EN 60715 RAIL
Installation:
Position the device on the OMEGA rail resting the upper teeth from top to
bottom.
Push the lower part towards the rail until the locking system engages.
Removal:
After switching off the module, with the help of a slotted screwdriver, unlock
the locking system located on the underside of the instrument.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>