ANKER 541 6 In 1 USB C Hub for iPad User Manual
- June 5, 2024
- Anker
Table of Contents
ANKER 541 6 In 1 USB C Hub for iPad
Important Safety Instructions
- Avoid dropping.
- Do not disassemble.
- Do not expose to liquids.
- For the safest and fastest charge, use original or certified cables.
- This product is suitable for moderate climates only.
- The maximum ambient temperature when using this product must not exceed 104°F / 40°C.
- Open flame sources, such as candles, must not be placed near this product.
- Only use a dry cloth or brush to clean this product.
At a Glance
| 1. USB-C Connector | Plug into an iPad’s USB-C port |
|---|---|
| 2. HDMI 2.0 Port | Up to 4K@60Hz |
| 3. Multi-Function USB-C Port | • Up to 60W pass-through charging for iPad |
• 5 Gbps data transfer
4. USB-A 3.0 Port| 5 Gb/s data transfer
5. SD 3.0 Card Slot| 104 MB/s data transfer
6. microSD Card Slot| 104 MB/s data transfer
7. 3.5 mm Audio Port| Connect earphones, a microphone, and other audio
devices
8. Power Indicator| Turn solid white when the hub is connected to an iPad
with a USB-C port
Using Your Hub
- To transfer data at maximum speed, your computer, peripherals, cables, and software must all support USB 3.0.
- Use an HDMI cable(not included) to stream videos via the HDMI 2.0 port.
- The SD card slot supports SD, SDHC, and SDXC card types up to 2TB, at speeds up to 104MB/s.
- The 3.5 mm audio port cannot support volume control for Apple earphones.
- No charger is included.
Specifications
| Data Speed | 5 Gbps |
|---|---|
| Supported Systems | iPad OS 13 and above |
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
The following importer is the responsible party:
Company Name: Fantasia Trading LLC
Address: 5350 Ontario Mills Pkwy, Suite 100, Ontario, CA 91764
Telephone: +1 (800) 988 7973
IC Statement
This device complies with Industry Canada license-ICES-003. Operation is
subject to the following two conditions: (1) This device may not cause
interference, and (2) This device must accept any interference, including
interference that may cause undesired operation of the device.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product type A8363 is in
compliance with Directive 2014/30 /EU & 2011/65/EU. The full text of the EU
declaration of conformity is available at the following internet address:
https://www.anker.com
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong
The following importer is the responsible party (for EU matters only):
Anker Innovations Deutschland GmbH
Georg-Muche-Strasse 3, 80807 Munich, Germany