GREEN CREATIVE GC-34993 9.5 Watt LED PL Lamp Installation Guide

: June 5, 2024
: GREEN CREATIVE

Table of Contents

GREEN CREATIVE GC-34993 9.5 Watt LED PL Lamp
ABOUT PRODUCT
LED PL LAMP INSTALLATION GUIDE – WARNING
LED PL LAMP INSTALLATION GUIDE – INSTALLATION STEPS
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

GREEN CREATIVE GC-34993 9.5 Watt LED PL Lamp

ABOUT PRODUCT

For model #: 5.5PLH/xxx/DIR/RC, 8.5PLH/xxx/DIR/R, 10.5PLH/xxx/DIR, 14.5PLH/xxx/DIR, 6PLV/xxx/DIR/R, 9.5PLV/xxx/DIR/R, 9.5PLV/xxx/DIR/RC, 11PLV/xxx/DIR/R, 17PLV/xxx/DIR Where xxx means 824-965 which indicates CRI and color temperature Pour les produits suivants:5.5PLH/xxx/DIR/RC, 8.5PLH/xxx/DIR/R, 10.5PLH/xxx/DIR, 14.5PLH/xxx/DIR, 6PLV/xxx/DIR/R, 9.5PLV/xxx/DIR/R, 9.5PLV/xxx/DIR/RC, 11PLV/xxx/DIR/R, 17PLV/xxx/DIR

LED PL LAMP INSTALLATION GUIDE – WARNING

NOTE: This retrofit kit is for a 4 PIN Horizontal and Vertical mounts and can replace 13W and 18W CFL lamps with G24q and GX24q bases.
CAUTION – IF THE LAMP OR LUMINAIRE EXHIBITS UNDESIRABLE OPERATION (BUZZING, FLICKERING, ETC.), IMMEDIATELY TURN OFF POWER, REMOVE LAMP FROM LUMINAIRE AND CONTACT THE MANUFACTURER.
WARNING – Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaire electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician. Installation should be performed only by a qualified electrician in accordance with the National Electrical Code and relevant local code.
WARNING – Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
WARNING – To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

Disconnect power at the source before installation, inspection or removal. Do not simply switch off fixture.
Not intended for use with emergency exit fixtures or emergency exit lights.
Operates on programmable ballasts only.
This lamp is not compatible with all ballasts. Before replacing existing fluorescent lamps, check compatibility of LED lamps and luminaire ballast.
Do not use if product is damaged.
Dimmable only on 0-10V dimmers. This lamp might not compatible with all dimmers.
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
Risk of fire or electric shock. Do not open or modify. No user serviceable parts inside.
SUITABLE FOR DAMP LOCATIONS. Suitable for use in wet locations when used in an outdoor-rated fixture. Not for use where directly exposed to the weather or water.
Complies with Part 15 of FCC. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received including interference that may cause undesired operation.
SUITABLE FOR “TYPE NON-IC” LUMINAIRES.
No external weight or mechanical force should be applied to lamp or components.
THE RETROFIT ASSEMBLY IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY UL OR AUTHORITIES HAVING JURISDICTION.
MIN. LAMP COMPARTMENT DIMENSIONS 6.10”(DIA) x 4.72”(H).
Intended for operation with the following ballasts:
- Philips Advance model #: ICF-2S18-H1-LD
- Sylvania model # : QTP 1/2x18CF/UNV DM
- Fulham model #: RHA-UNV-218-C

LED PL LAMP INSTALLATION GUIDE – INSTALLATION STEPS

Switch-off power to luminaire.
Remove the cover lens (if provided).
Carefully remove all existing CFL lamps from luminaire. Note: Verify that the ballast is compatible with LED PL lamps, see the ballast compatibility list.
Confirm the lampholder has a G24q or GX24q socket.
Insert the LED PL lamp into the open socket within the fixture. Ensure pins are firmly seated in the lampholder.
Switch on power to luminaire and installation is now complete.