Topeak TW031 Prepstand eUP PRO User Guide

Topeak TW031 Prepstand eUP PRO User Guide

Warning
READ ASSEMBLY INSTRUCTIONS THOROUGHLY. Care should be taken during assembly as the built-in pressurized nitrogen cartridge may be accidentally deployed. ENSURE THERE IS ADEQUATE SPACE ABOVE THE CLAMP HEAD UNIT TO AVOID INJURY OR DAMAGE

PARTS DESCRIPTION

<ol

•  360° Rotation knob
•  Clamp holder
•  Clamp jaw lever
•  Clamp
•  Clamp jaw
•  Extension tube
•  QR clamp lever
•  Wheel
• Reinforcement support unit
•  Support legs
•  Cable end holder
•  Cable retainer
•  Pedal

Support Leg Assembly

DO NOT position the quick-release lever where it can be accidentally released. Always fully extend support leg assembly for a steady foundation. Close the quick-release lever

CLAMP ASSEMBLY

Insert the clamp into the clam holder and rotate the lever until   ratchet teeth are fully engaged

Extend the clamp holder lever for the following assembly procedure.

REINFORCING SUPPORT UNIT ASSEMBLY

Make sure the support units are properly assembled as they are specific for each leg denoted L end

REINFORCING SUPPORT UNIT ASSEMBLY

Periodically check bolts for proper torque values and any wear.

Cable Assembly

Ensure cable end is inserted into anchor correctly Place pedal correctly with downside on the floor Remove the cable retainerPlace the cable end into If you can’t place the cable end into the notch smoothly. DO NOT STRETCH THE CABLE TO PLACE IT. Please check whether the cable is out of position you can’t place the cable end into the notch smoothly. DO NOT STRETCH THE CABLE TO PLACE IT. Please check whether the cable is out of position first CARE SHOULD BE TAKEN DURING ASSEMBLY as the built-in pressurized nitrogen cartridge may be accidentally deployed. Ensure there is adequate space above the clamp head unit to avoid injury or damage.

Adjust the knob to tighten the cable.

Install cable retainer as shown. The inner cable will stretch over time. Adjust or replace cable as needed.

FUNCTION TEST

Gently depress the pedal. The extension tube should lift. Depress the pedal and push down the clamp holder to lower the extension tube If the clamp still does not raise or lower after checking assembly, it may indicate that the built-in pressurized nitrogen cartridge is damaged. Please refer to page 14 of this User’s Guide on how to examine the cartridge for proper operation

ATTACH THE BIKE

Rotate the clamp jaw lever to adjust the clamp width. Once the clamp is set to the desired width, quick adjustments can be made by opening the lever.If there is a carbon seat post on the bike to be clamped, replace it with an aluminum seaport before using the Prepstand up for safety purposes.

LIFT or LOWER
The built-in pressurized nitrogen cartridge will provide lift assist while you press the pedal. You can stop at any height by releasing the pedal. To lower, press pedal and push down on clamp. Once the clamp is at the lowest position, release the pedal to lock the clamp in position.

WARNING

Firmly hold the bike before loosening the 360° knob to disengage ratchet teeth. Rotate bike to the desired position, then tighten the 360° knob to re- engage ratchet teeth to lock the clamp position. ENSURE RATCHET TEETH ARE FULLY ENGAGED and always check stability when operating the stand.

DISASSEMBLY

Remove the cable retainer

Loosen both adjusting knobs for safety during cable disassembly Ensure there is adequate space above the clamp head unit to avoid injury or damage. The pressurized nitrogen cartridge may cause injury or damage.

Please make sure the clamp holder has been pushed down to the lowest position Loosen the 360° knob to disengage ratchet teeth and remove the clamp from the clamp holder.Be careful not to pinch your fingers when folding stand legs.

EXAMINING PRESSURIZED NITROGEN CARTRIDGE

The built-in pressurized nitrogen cartridge may be damaged if the clamp head does not lift or lower smoothly during normal operation. Inspect by pressing the cable end holder down to check the function of the pressurized nitrogen cartridge. While the cable end holder is depressed, the clamp holder should raise and can be lowered by pressing down on the clamp holder. If it doesn’t work properly with this method, then the built-in nitrogen cartridge is confirmed to be damaged. Contact your local Topeak dealer for cartridge replacement. Care must be taken when examining the pressurized nitrogen cartridge. Accidental deployment of the pressurized nitrogen cartridge may cause injury or damage.

PARTS DESCRIPTION

The tool tray can be mounted directly to the work stand.For cartridge replacement, it is recommended ta return repair stand to dealer to ensure function and safety

WARNING NOTES

1. Always fully extend support leg assembly and install a reinforcing support unit” between, “assembly for a steady foundation.
2.  In case of accidental operation, ensure there is adequate space above the stand to prevent injury or damage during assembly and disassembly of the stand.
3.  Ensure 360° knob is tightened adequately to engage ratchet teeth during assembly and operation.
4.  QR clamp lever should be tightened correctly when assembling and operating stand.
5.  To prevent possible damage to the bike, DO NOT over-tighten the clamp.
6.  The stand may tilt or fall over if the bike being clamped is over 35kg.
7.  Make sure the clamp assembly is in the lowest position and hold the bike before loosening the clamp.
8.  DO NOT use the stand wheel to reposition the stand if a bike is clamped
9. Keep stand pedal positioned safely when storing or using the stand to prevent accidental operation of the pressurized nitrogen cartridge.
10.  The wheel chock DOES NOT prevent the stand from tipping. Always check the stability of the stand before and during use.

WARRANTY

2-year Warranty: All mechanical components against manufacturer defects only. Warranty Claim Requirements To obtain warranty service, you must have your original sales receipt. Items returned without a sales receipt will assume that the warranty begins on the date of manufacture. All warranties will be void if the product is damaged due to user crash, abuse, system alteration, modification, or use in any way not intended as described in this manual. The specifications and design are subject to change without notice. Please contact your Topeak dealer with any questions, For USA customer service call: 1-800-250-3068 at www.topeak.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>