TOPEAK Tetrafender M1 Front Mudguard Instruction Manual
- June 5, 2024
- TOPEAK
Table of Contents
TETRAFENDER M1 / M2
TETRAFENDER M1 ( FRONT FORK ) | TETRAFENDER M2 ( SEATSTAVS) |
---|
- Mounting base A
- Mounting base B
- Rubber pad
- Velcro straps
- Strap tensioner
- Front
- Rear
- Allen key 2.5mm x 1
- Wheel size compatibility: 26-29 “( M1, M2
- Tire width compatibility:< 2.8″
- Width compatibility: front fork 115-145mm
(M1), seat stays 95-125mm (M2)
| The
seat stays angle must be greater than 30 degrees for proper operation.
---|---
| Not suitable to mount on frames with unique geometries.
WARNING
| MT COMPATIBILITY
FRONT FORK WIDTH CAPACITY| M2 COMPATIBILITY
SEATSTAYS WIDTH CAPACITY
---|---|---
TetraFender has a mounting length of 200mm.
Seatstays and front forks must not contain any obstacles that prevent mounting
TetraFender securely.| Compatible with front fork width within 115-145mm.|
Compatible with seatstays width within 95-125mm.
INSTALLATION
UNSCREW 6 BOLTS OF MOUNTING BASE.
TETRAFENDER MT ( FRONT FORK )
ANGLE ADJUSTMENT
Adjustable aluminum struts for quick, perfect alignment and good tire coverage
TETRAFENDER M1 ( FRONT FORK )
TETRAFENDER M2 ( SEATSTAYS)
ANGLE ADJUSTMENT
TWO-PIECE & DUAL TONE DESIGN
Take Velcro straps with a metal loop and route around front forks/ seat stays.
Buckle metal loop into the hook of strap tensioner.
Adjust the strap tensioner hook to the lowest position with a 2.5mm Allen key.
Tighten to secure the mounting base to the bike frame.
Use a 2.5 mm Allen key to tighten the mounting base and bend slightly.
VERY IMPORTANT
TIGHTEN ALL BOLTS AFTER INSTALLATION IS COMPLETE.
IMPORTANT NOTE:
Tighten all bolts after installation is complete.
If the TetraFender is pushed to the left side, please adjust the left mounting position down.
Ensure TetraFender is aligned with the tire. After installation, tighten bolts to recommended torque value. Adjust TetraFender for adequate tire clearance. Misalignment or inadequate tire clearance will {2278; 1g.-ta”ender or be tare and rider.
ANGLE ADJUSTMENT
TETRAFENDER M1
( FRONT FORK )| TETRAFENDER M2
( SEATSTAYS )
The proper tire clearance of Tetra Fender must be larger than 8mm.
Improper tire clearance may cause damage to TetraFender, your bike, or bodily
injury.| The proper tire clearance of TetraFender must be larger than 20mm.
Improper tire clearance may cause damage to TetraFender, your bike, or bodily
injury.
FRONT FORK/ SEATSTAV
|
Do not install the Tetra Fender on screw holes, hose stops, or brake hoses.|
When fixing mounting straps, do not inadvertently tighten over brake hose or
derailleur cable
WARNING NOTES
- Clean frame/fork mounting area prior to installing TetraFender.
- Check TetraFender after every ride for secure mounting. If there is any exaggerated movement of TetraFender during a ride, stop riding immediately.
- Do not engage in extreme riding, such as jumping, when using TetraFender.
WARRANTY
2year Warranty: All mechanical components against manufacturer defects only.
Warranty Claim Requirements
To obtain warranty service, you must have your original sales receipt. Items
returned without a sales receipt will assume that the warranty begins on the
date of manufacture. All warranties will be void if the product is damaged due
to user crash, abuse, system alteration, modification, or used in any way not
intended as described in this manual.
- The specifications and design are subject to change without notice.
Please contact your Topeak dealer with any questions. For USA customer service, call: 1800-250-3068 www.topeak.com
Copyright © Topeak, Inc. 2021 TC9660_TC9661_TC9662_M_A3_ML 20211125
Documents / Resources
|
TOPEAK Tetrafender M1 Front
Mudguard
[pdf] Instruction Manual
Tetrafender M1 Front Mudguard, Tetrafender M1, Front Mudguard
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>