Clarke CAT131 Air Impact Wrench Instruction Manual

AIR IMPACT WRENCH
MODEL NO: CAT131 & 132
PART NO: 3120145 / 3120146

OPERATING & MAINTENANCE
INSTRUCTIONS
ORIGINAL INSTRUCTIONS GC02/22 – Rev 4

INTRODUCTION

Thank you for purchasing this CLARKE Impact Wrench. The CAT131 and CAT132 are identical wrenches, the CAT132 being supplied in a molded plastic storage case that contains the following.

• 1 x Mini Oiler
• 1 x Hex Key
• 1 x Oil Bottle| • 1 x Extension Bar
• 1 x Snap Connector fitting
• 10 Impact Sockets, (9, 10, 11, 13, 14, 17, 19, 22, 24 & 27mm sizes)
---|---

Please read all of the safety and operating instructions carefully before using this product. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you a long and satisfactory service

OVERVIEW

SPECIFICATION

4.2 kg complete (CAT132)
Wrench Dimensions (L x W x H)| 210 x 190 x 90 mm

Please note that the details and specifications contained herein are correct at the time of going to print. However, Clarke International reserves the right to change specifications at any time without prior notice.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase. This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended.
Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission. This guarantee does not affect your statutory rights.

GENERAL SAFETY RULES

CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY.

WORK ENVIRONMENT

1. Keep the work area clean and tidy.
2. Dress appropriately – Do not wear loose clothing or jewelry. Tie long hair out of the way.
3. Keep children and visitors away – Do not let children handle the tool.
4. Do not operate the tool where there are flammable liquids or gases.

USE OF POWER TOOLS

1. Stay alert and use common sense – do not operate the tool when you are tired or under the influence of alcohol, drugs or medication.

2. Always wear eye protectors when using the tool. Eye protectors must provide protection from flying particles from the front and the side. Ear protectors should also be worn.

3. Do not overreach – Keep proper footing and balance at all times.

4. Never use oxygen, CO², combustible gases, or any type of bottled gas as a source of power for this tool.

5. Do not connect the air supply hose with your finger on the trigger.

6. Do not exceed the maximum pressure for the tool of 90 psi / 6.2 bar.

7. Keep the air supply hose away from heat, oil, and sharp edges.

8. Do not fit the tool to any stand or clamping device that may damage it.

9. Check hoses for leaks or worn conditions before use, and ensure that all connections are secure.

10. Do not use the tool for any purpose than that described in this manual.

11. Do not carry out any alterations or modifications to the tool.

12. Always disconnect from the air supply when:
    • Performing any maintenance.
    • The tool is not in use.
    • The tool will be left unattended.
    • Moving to another work area.
    • Passing the tool to another person.

13. Never use the tool if it is defective or operating abnormally.

14. This tool should be serviced at regular intervals by qualified personnel.

15. Avoid damaging the tool for example by applying an excessive force of any kind.

16. Always maintain the tool with care. Keep it clean for the best and safest performance.

17. Quick change couplings should not be located at the tool. They add weight and could fail due to vibration.

18. Do not force or misuse the tool. It will do a better and safer job at the rate at which it was designed.

19. Do not remove any labels. Damaged labels should be replaced.

20. This tool vibrates with use. Vibration may be harmful to your hands or arms. Stop using the tool if discomfort, a tingling feeling or pain occurs. Seek medical advice before resuming use.

IMPACT WRENCH SAFETY INSTRUCTIONS

1. Always use the impact wrench in the manner and for the functions described in these instructions.
2. Always ensure the wrench is not moving and disconnected from the air supply when changing sockets etc. Use only Impact Wrench sockets….DO NOT use standard sockets.
3. Always finish tightening wheel nuts or engine parts with a torque wrench or suitable spanner to the correct torque as recommended by the vehicle manufacturer.
4. Always avoid excessive use of the impact wrench. When tightening a nut or bolt, never allow the wrench to impact more than 8 times – to avoid over tightening – 3 to 4 impacts is normally sufficient.
5. Always ensure that the socket is correctly installed before switching it on.
6. Always only use sockets that are specified for impact wrench use.
7. Due to the possible presence of asbestos dust from brake linings, always wear suitable respiratory protection.
8. Never carry the impact wrench by the air supply hose.
9. Always disconnect from the air supply when changing impact sockets or when the wrench is not required for immediate use in order to avoid accidental starting.
10. Always store this product in a dry, secure place out of reach of children or untrained users.
11. Always use both hands to control the impact wrench.
12. Always ensure the wrench has stopped before putting it down after use.
13. Never carry the tool by the air hose.
14. Never carry the tool with your finger on the trigger.

SAFETY SYMBOLS

The following safety symbols are to be found on the tool.

| Read this instruction booklet carefully before use.
---|---
| Wear eye protection.
| Wear ear protection.

COMPRESSED AIR REQUIREMENTS

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF COMPRESSORS AND COMPRESSED AIR SUPPLY.

A typical airline layout is shown below.

AIR SYSTEM LAYOUT :

1. Air Tool
2. Air Hose 3/8″ (I.D.)
3. Oiler
4. Pressure Regulator
5. Filter
6. Shut Off Valve
7. Whip Hose
8. Coupler Body And Connector| 9. Drain Valve
10. 1/2″ or larger pipe and fitting
11. Air Dryer
12. 1″ or larger pipe and fitting
13. Air Compressor
14. Auto Drain
15. Drain Valve
---|---

• Use only clean, dry, regulated compressed air as a power source.
• Air compressors used with the tool must comply with the appropriate European Community Safety Directives.
• A build-up of moisture or oil in the air compressor will accelerate wear and corrosion in the tool. Ensure any moisture is drained from the compressor daily and the inlet filter is kept clean.
• If an unusually long air hose is required, (over 8 meters), the line pressure or the hose inside diameter may need to be increased.
• The air hose must be rated at least 150% of the maximum operating pressure of the tool.
• If an automatic in-line filter/regulator is used, it will keep the tool in good condition, but should be regularly checked and topped up with oil. Clarke airline oil should be used, and the lubricator adjusted to approx 2 drops per minute.
• For optimum performance, it is recommended that a 3/8” ID hose is used.
• Never exceed the maximum operating pressure for the tool. It is recommended that air pressure to this tool does not exceed 90 psi at the tool when running. Higher pressures and dirty air will shorten the life of the tool due to faster wear and is a possible safety hazard.

CONNECTING THE AIRLINE

NOTE: Ensure the compressor is turned off.

1. If required, connect an in-line mini oiler to the tool.
   • A mini oiler helps to prolong the life of the impact wrench.
   

2. If a mini-oiler is not being used, run a few drops of oil through the tool before use. It can be entered through the air inlet connector or via the hose at the nearest connection to the air supply.

3. Connect a suitable hose as shown.

4. Connect the other end of the hose to the compressor.
   

5. Turn on the air supply and check for air leaks. Rectify any found before proceeding.
   • PTFE tape may be useful for sealing threaded connections. Your air tool is now ready for use. You can fit a whip hose with a quick fit coupling if required, available from
   your Clarke dealer.
   **Clarke Air Line Oil (part no. 3050825) is available from your Clarke dealer.

OPERATION

FITTING THE IMPACT SOCKET
WARNING: NEVER USE STANDARD SOCKETS. THESE MAY SHATTER WITH SERIOUS CONSEQUENCES. ONLY USE IMPACT SOCKETS DESIGNED FOR USE WITH IMPACT TOOLS.

1. Select the impact socket you require, which must be in good condition and fit the tool exactly.
2. Push the socket onto the square drive as shown.
   

OPERATING THE IMPACT WRENCH

1. Locate the socket over the nut to be tightened or loosened.
2. Squeeze the trigger to start the wrench.
3. Release the trigger switch to stop the wrench.
   • The square drive shaft will continue to rotate very briefly after the trigger has been released.

ADJUSTING THE POWER

1. To adjust the power, set the air regulator to one of the 3 settings available. (Setting 1-Low, 3 -High)
   • These numbers are only for reference and do not denote a specific amount of power.

SELECTING FORWARD AND REVERSE
WARNING: WAIT UNTIL THE ANVIL HAS STOPPED ROTATING BEFORE OPERATING THE FORWARD/REVERSE BUTTON.

Forward/Reverse rotation is selected by pushing the combined Forward/ Reverse knob/power regulator in the direction shown by the arrow on the back of the wrench.

1. For normal tightening, the wrench should be operated in the forward (F) direction.
   • For loosening, the wrench should be operated in the reverse (R) direction.

DISCONNECTING THE AIR SUPPLY

1. Do not disconnect the air supply hose until the compressor has been shut down and the compressed air released. Residual pressure can be expelled from the tool by running it until it stops.
2. Refer to the compressor instruction manual for the procedure to shut down and vent the compressed air.
3. Once the pressure has been released, disconnect the air supply hose from the air tool.

MAINTENANCE

WARNING: MAKE SURE THAT THE AIR TOOL IS DISCONNECTED FROM THE AIR SUPPLY BEFORE STARTING ANY CLEANING OR MAINTENANCE PROCEDURES.

DAILY/SUBJECT TO USAGE

1. Before use, drain water from the airline filter and compressor.
2. Pour a few drops of Clarke air-line oil, into the tool air inlet. This should be carried out regardless of whether or not an in-line mini oiler is used. If an in-line mini oiler is
   not used, this procedure should be repeated after every two to three hours of use.

• Check the air inlet filter for blockage and clean if needed. Lubricate the motor by first removing the screw shown with a hex key.
• A hex key is provided for removing the end cover from the wrench.

Using a grease gun, insert the gun nozzle into the grease port. Several drops of grease are recommended for lubrication.

• This will protect the motor in good rotating condition.

INTERNAL CLEANING

1. Grit or gum deposits in the tool may reduce efficiency and cause the tool to run erratically. This condition can be corrected by cleaning the air strainer and flushing out the tool with gum solvent or oil.
2. Failing this, the tool should be disassembled, thoroughly cleaned, dried, and reassembled.
3. The tool may be dismantled by removing the front cover using the hex key supplied prior to replacing any worn or damaged parts.
4. You may prefer to take the tool to your Clarke dealer if internal maintenance is required.
5. While in a dismantled state, always grease the hammer mechanism by applying a small amount of good quality bearing grease.

TROUBLESHOOTING

worn.
2. Worn or sticking mechanism due to lack of lubricant.| 1. Return to Clarke dealer for repair.
2. Drip air tool lubricating
oil into the air inlet. Allow the oil to soak moving parts before using.
The tool runs slowly. Air flows weakly from the exhaust.| 1. Motor parts jammed with gum/dirt.
2. Air-line regulator in the closed position.
3. General airflow blocked by dirt.| 1. Examine the inlet air filter for blockage. Drip a few
drops of air tool lubricating oil into the air inlet.
2. Adjust the in-line regulator to open position.
3. Operate tool in short bursts.
The tool will not run. Air flows freely from the exhaust.| 1. Motor vanes stuck due to buildup of foreign material.| 1. Disconnect air supply and rotate tool assembly manually.
2. Try operating the tool in
short bursts.
3. Tap the motor housing gently with a rubber mallet.
4. Drip a few drops of air tool lubricating oil into air inlet to soak moving parts.
The tool will not shut off.| 1. Throttle 0-rings damaged or ill-fitting in the seat.| 1. Return to Clarke dealer for repair.

PERFORMANCE
Please note that factors other than the tool may affect its operation and efficiency such as reduced compressor output, excessive drain on the airline, moisture or restrictions in the air-line, or the use of connectors of improper size or poor condition which will reduce air supply.

PARTS LIST

PARTS DIAGRAM

DECLARATION OF CONFORMITY

PARTS & SERVICE:
0208 988 7400 Parts
Inquiries Parts@clarkeinternational.com
Servicing & Technical Enquiries Service@clarkeinternational.com
SALES: UK 01992 565333 or Export 00 44 (0)1992 565335
Clarke INTERNATIONAL Hemnall Street, Epping, Essex CM16 4LG
www.clarkeinternational.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>