kikkaboo 0728256 Vicenza 3-In-1 Stroller Set Instruction Manual

: June 5, 2024
: kikkaboo

kikkaboo 0728256 Vicenza 3-In-1 Stroller Set

kikkaboo-0728256-Vicenza-3-In-1-Stroller Set-product-
image

kikkaboo-0728256-Vicenza-3-In-1-Stroller Set-02

SAFETY INSTRUCTION

WARNINGS :

Always lock the brake when put or carry a child
Leaving the baby without care may cause a danger
Use the braces when the baby begins to sit at his own.
Do not use an additional mattress in the product.
Before use be sure that the assembling mechanisms are blocked
Always use the crotch belt together with the help belt.
Every load handing on the handle affects its stability.
This product is not designated to go roller blades or to run.
This stroller is indented to bear only one baby.
This stroller is designated for the babies up to 0-48 months and weight 22kg and complies on EN1888-1&2:2018.
Do not leave the stroller with a baby on the slope, even if the brake is locked.
Do not use the stroller, if any component is damaged.
During the assembling and disassembling the stroller, be sure that the baby is at the safe distance
Making any adjustments, make sure that the movable parts are not close to the baby’s body.
Always lock the brake when stops.
Maximum load of basket is 3 kg
Maximum load of bag is 2 kg
Every bag or other load handing on the handle affects its stability.
Only the original parts, confirmed by the producer should be used in this product.
Driving on the pavement or any other step the front axle should be lifted
Do not drive the stroller through the stairs
The stroller should be kept away from babies

PARTS LIST

CARSEAT
FRAME
SEAT
CARRYCOT
ADAPTORS SET x2
REAR WHEELS x2
FRONT WHEELS x2
BUMPER BAR
CANOPY
FOOTCOVER
MAMABAG

OPENING OF THE STROLLER

2a. Lift the handle up as picture 2a
2b. When the stroller is opened as picture 2b, you should hear “click” sounds on both side of the stroller, please examine if the stroller is locked in safety position before you use it.

ASSEMBLING/DISASSEMBLING OF THE REAR WHEELS

3a. To assemble the rear wheels: Take one side of rear wheels, Insert the rear axle into the plastic hole as picture 3a, until it is locked, install the other side of the rear wheel
in the same way.
3b. To disassemble the rear wheels: Pull the rear wheel express iron as arrow 1, remove the rear wheel in the direction of arrow 2 then nish the disassemble

ASSEMBLING/DISASSEMBLING OF THE FRONT WHEELS

4a. To assemble the front wheels: Take one side of front wheels, insert the vertical shaft into the plastic hole on the wheel seat as picture 4a, until it is locked, install the
other side of the front wheel in the same way
4b. To disassemble the front wheels: press the small metal pins as arrow 1, at the same time use your hand to pull out the front wheel as arrow 2 to finish disassemble

DEGREE ROTATION OF THE FRONT WHEELS

5a. Lift up the plastic button on the front wheels to lock it not rotated at 360 degree, press down the plastic button to release it can be rotated at 360degree as the arrow in the
picture 5a.
5b. BRAKING THE STROLLER
Step down the brake pedal to brake the stroller, lift up the pedal to release the brake as picture 5b
WARNING: Always lock the brake when put or carry a child

ASSEMBLING OF THE SEAT

Assemble the seat as picture 6 (back to mother), you should hear a ”click” sounds on both side to make sure the seat is locked in safety position.
To reverse the seat in different direction (face to mother) in same way.

ASSEMBLING OF THE BUMPER

7a. Insert the bumper on both sides of the seat as picture 7a.
Note: please make sure to lock the bumper in place when you heard a “click” sound
7b. DISASSEMBLING OF THE BUMPER
Press the button as arrow 1 in picture 7b to remove the bumper.

ASSEMBLING OF THE CANOPY

Insert the canopy plastic into the seat as picture 8a
8b. OPENING AND FOLDING OF THE CANOPY
Extend or fold the canopy as picture 8b

TELESCOPE HANDLE BAR

Press the button as the arrow 1 in picture 9

ADJUSTING OF THE FOOTREST

Press the button as arrow 1 in the picture 10 to adjust the footrest in 3 position

ADJUSTING OF THE BACKREST

Lift up the button as arrow1 in the picture 11a to adjust the backrest to be in 3 position(sleeping or seat) as picture 11b.

REVERSIBLE SEAT

Pull out the button and lift up the seat as arrow direction in picture 12a, then assemble the seat in opposite direction as picture 12b, insert the seat in the frame to finish
the assemble.

FOLDING OF THE STROLLER

When the seat back to the mother, Telescope the handle bar to the shortest position as 13a, fold the seat to the handle side as 13b, Then press and hold the button as arrow
3 not released, in same time lift up the carry handle as arrow 4 in the picture 13c, finally release the button to fold the stroller as picture 13d.
When the seat face to the mother, Telescope the handle bar to the shortest position as 13e, fold the backrest to the handle side as as 13f, Then press and hold the button as
arrow 3 not released, in same time lift up the carry handle as arrow 4 in the picture 13g, finally release the button to fold the stroller as picture 13h.
WARNING: BEFORE FOLDING,PLEASE MAKE SURE TO TELESCOPE THE HANDLE BAR TO THE SHORTEST POSITION IN ORDER TO PROTECT THE HANDLE NOT TO TOUCH THE FLOOR

ASSEMBLING THE CARSEAT 0+ GROUP

NOTE! Lock the safety brake before assembling the carseat. Remove the seat from the frame as picture14a; Insert one set down adaptor on the seat as picture14b;
NOTE! The down adaptor is universal for carrycot and carseat for height Assembly the carseat with the adapters that are the part of its set. Stick the adapters in the handles located at the base of the carseat handle as picture 14c. You should hear a “click” to finish the assemble as picture 14d.
NOTE! Before using, make sure that the adapters and the seat are properly assembled.

REMOVING THE CARSEAT 0+ GROUP

NOTE! Lock the safety brake before removing the seat
In order to remove the seat with the adapters from the stroller frame, raise both levers on the adapters as picture 14e,and lift the seat up. In order to unstick the adapters
from the carseat. press the buttons located on the upper edges of the carseat and remove the adapters
NOTE! The manual, maintenance rules, warnings and guarantee card of the stroller 0+ are in their original package with the seat.

ASSEMBLING OF THE CARRYCOT

In order to unfold the pram body, remove the bedding and the mattress, and then squeeze the metal tensioners on the bottom plate of the pram body in the direction of
the arrows (picture 15a-15e), until it locks in special holders. You should hear a “click”sounds locking the tensioner in the holder
NOTE! The pram body is designed for children up to 6 months old weighing up to 9 kg, which cannot sit, kneel or trundle by themselves. Stop using the stroller body if your
child starts sitting kneeling or trundling by itself
WARING: Do not use an additional mattress of thickness of more than 15mm.
The pram body canopy has 4-step adjustment. In order to adjust it, press simultaneously the buttons located at the base of the carrying handle and adjust the desire
position. The external canopy rant is also a carrying handle. In order to move the stroller body by holding the handle, place it in the top position
NOTE! Make sure that the carrying handle is locked in the correct position before you move the pram body
NOTE! The pram body can be assembled only back to the direction of travel( in this setting, the person pushing the pram is face to face with a child)
NOTE! Lock the safety brake before you assembly the pram body on the stroller frame
In order to assembly the pram body on the stroller frame, removed the bumper from the stroller ,then removed the seat , then insert the universal adapters on the frame and assemble the pram, You should hear a click as 15f
NOTE! Before using, make sure that the stroller body is properly assembled

REMOVING THE CARRYCOT

NOTE! Lock the safety brake before you remove the pram body
In order to remove the pram body, press simultaneously the buttons located on the adapters of the pram body and pull it upwards as 15g

USING THE SAFETY BELT

Picture 16a-16b: There are 2 position for safety belt, the up position is suitable for one baby more than 6 months, the bottom position is suitable for one baby under than 6 months

USING THE SAFETY BUCKLE:

Click here to lock the safety buckle on both sides as 16c. Press the middle button to release the safety button as 16c. You can adjust the length of the seat belt by pulling the safety buckle on both sides as needed.