KitchenAid KSM150PSCH0 Quart Tilt Head Stand Mixer Instruction Manual
- July 12, 2024
- KitchenAid
Table of Contents
- KSM150PSCH0 Quart Tilt Head Stand Mixer
- PROOF OF PURCHASE & PRODUCT REGISTRATION
- STAND MIXER SAFETY
- IMPORTANT SAFEGUARDS
- HOW TO ORDER ACCESSORIES AND REPLACEMENT PARTS
- TROUBLESHOOTING PROBLEMS
- ASSEMBLING YOUR TILT-HEAD STAND MIXER
- **USING YOUR POURING SHIELD***
- TILT-HEAD STAND MIXER USE
- CARE AND CLEANING
- SPEED CONTROL GUIDE
- ATTACHMENTS AND ACCESSORIES
- GENERAL INSTRUCTIONS
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
KITCHENAID KSM150PSCH0
Owner’s Manual
KSM150PSCH0 Quart Tilt Head Stand Mixer
This Owner’s Manual is provided and hosted by Appliance Factory
Parts.
Appliance Factory Parts
Experts in BBQ, Humidifier, & Appliance Parts
1-800-955-7075
Shop genuine replacement parts for
KITCHENAID
KSM150PSCH0
Find Your KITCHENAID Mixer Parts – Select From 532
Models
——– Manual continues below ——–
PROOF OF PURCHASE & PRODUCT REGISTRATION
Always keep a copy of the sales receipt showing the date of purchase of your
Stand Mixer. Proof of purchase will assure you of in-warranty service.
Before you use your Stand Mixer, please fill out and mail your product
registration card packed with the unit.
This card will enable us to contact you in the unlikely event of a product
safety notification and assist us in complying with the provisions of the
Consumer Product Safety Act. This card does not verify your warranty.
Please complete the following for your personal records:
Model Number……………….
Serial Number ……………………
Date Purchased ………………………..
Store Name…………………………………….
STAND MIXER SAFETY
Yo ur safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your
appliance. Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and
others.
All safety messages will follow the safety alert symbol and either the word
“DANGER” or “WARNING.” These words mean:
Danger
Yo u can be killed or seriously injured if you don’t immediately follow
instructions.
Warning
You can be killed or seriously injured if you don’t follow instructions.
All safety messages will tell you what the potential hazard is, tell you how
to reduce the chance of injury, and tell you what can happen if the
instructions are not followed.
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed including the following:
- Read all instructions.
- To protect against risk of electrical shock, do not put Stand Mixer in water or other liquid.
- Close supervision is necessary when any appliance is used by or near children.
- Unplug Stand Mixer from outlet when not in use, before putting on or taking off parts and before cleaning.
- Avoid contacting moving parts. Keep hands, hair, clothing, as well as spatulas and other utensils away from beater during operation to reduce the risk of injury to persons and/or damage to the Stand Mixer.
- Do not operate Stand Mixer with a damaged cord or plug or after the Stand Mixer malfunctions, or is dropped or damaged in any manner. Return appliance to the nearest Authorized Service Center for examination, repair or electrical or mechanical adjustment. Call the KitchenAid Customer Satisfaction Center at 1-800-541-6390 for more information.
- The use of attachments not recommended or sold by KitchenAid may cause fire, electrical shock or injury.
- Do not use the Stand Mixer outdoors.
- Do not let the cord hang over edge of table or counter.
- Remove flat beater, wire whip or dough hook from Stand Mixer before washing.
- This product is designed for household use only.
SAVE THESE INSTRUCTIONS
ELECTRICAL REQUIREMENTS
Volts: 120 A.C. only. Hertz: 60 The wattage rating for your Stand Mixer is
printed on a tag under the mixer base. It is also listed on the trim band.
If the power cord is too short, have a qualified electrician or serviceman
install an outlet near the appliance.
WARNING
Electrical Shock Hazard Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical
shock.
KITCHENAID® STAND MIXER WARRANTY
Length of Warranty:| KitchenAid Will Pay For:| KitchenAid Will
Not Pay For:
---|---|---
50 United States, the District of Columbia, Canada, and Puerto Rico:
One-year limited warranty from date of purchase.| 50 United States, the
District of Columbia
and Canada: Hasslefree replacement of your Stand Mixer. See the following page
for details on how to arrange for replacement. OR In Puerto Rico: The
replacement parts and repair labor costs to correct defects in materials and
workmanship. Service must be provided by an Authorized KitchenAid Service
Center.
To arrange for service, follow the instructions on page 6.| A. Repairs when
Stand Mixer is used in other than normal single family home use.
B. Damage resulting from accident, alteration, misuse or abuse or use with
products not approved by KitchenAid.
C. Replacement parts or repair labor costs for Stand Mixer when operated
outside the country of purchase.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
IMPLIED WARRANTIES, INCLUDING TO THE EXTENT APPLICABLE WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXCLUDED TO THE
EXTENT LEGALLY PERMISSIBLE. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW
ARE LIMITED TO ONE YEAR, OR THE SHORTEST PERIOD ALLOWED BY LAW. SOME STATES
AND PROVINCES DO NOT ALLOW LIMITATIONS OR EXCLUSIONS ON HOW LONG AN IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS LASTS, SO THE ABOVE LIMITATIONS OR
EXCLUSIONS MAY NOT APPLY TO YOU. IF THIS PRODUCT FAILS TO WORK AS WARRANTED,
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY SHALL BE REPAIR OR REPLACEMENT ACCORDING
TO THE TERMS OF THIS LIMITED WARRANTY. KITCHENAID AND KITCHENAID CANADA DO NOT
ASSUME ANY RESPONSIBILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. This
warranty gives you specific legal rights and you may also have other rights
which vary from state to state or province to province.
HASSLE-FREE REPLACEMENT WARRANTY – 50 UNITED STATES AND DISTRICT OF
COLUMBIA
We’re so confident the quality of our products meets the exacting standards
of KitchenAid that, if your Stand Mixer should fail within the first year of
ownership, KitchenAid will arrange to deliver an identical or comparable
replacement to your door free of charge and arrange to have your original
Stand Mixer returned to us. Your replacement unit will also be covered by our
one year limited warranty. Please follow these instructions to receive this
quality service.
If your KitchenAid® Stand Mixer should fail within the first year of
ownership, simply call our toll-free Customer Satisfaction Center at
1-800-541-6390 Monday through Friday, 8
a.m. to 8 p.m. (Eastern Time), or Saturday, 10 a.m. to 5 p.m. Give the
consultant your complete shipping address. (No P.O. Box numbers, please.)
When you receive your replacement Stand Mixer, use the carton and packing
materials to pack up your original Stand Mixer. In the carton, include your
name and address on a sheet of paper along with a copy of the proof of
purchase (register receipt, credit card slip, etc.).
HASSLE-FREE REPLACEMENT WARRANTY
– CANADA
We’re so confident the quality of our products meets the exactingstandards
of the KitchenAid® brand that, if your Stand Mixer should fail within the
first year of ownership, KitchenAid Canada will replace your Stand Mixer with
an identical or comparable replacement. Your replacement unit will also be
covered by our one year limited warranty.
Please follow these instructions to receive this quality service.
If your KitchenAid® Stand Mixer should fail within the first year of
ownership, take the Stand Mixer or ship collect to an Authorized KitchenAid
Service Centre. In the carton include your name and complete shipping address
along with a copy of the proof of purchase (register receipt, credit card
slip, etc.). Your replacement Stand Mixer will be returned prepaid and
insured. If you are unable to obtain satisfactory service in this manner call
our toll-free Customer Interaction Centre at
1-800-807-6777. Or write to us at:
Customer Interaction Centre KitchenAid Canada 1901 Minnesota Court
Mississauga, ON L5N 3A7
HOW TO ARRANGE FOR WARRANTY SERVICE IN PUERTO RICO
Your KitchenAid® Stand Mixer is covered by a one-year limited warranty from
the date of purchase. KitchenAid will pay for replacement parts and labor
costs to correct defects in materials and workmanship. Service must be
provided by an Authorized KitchenAid Service Center.
Ta ke the Stand Mixer or ship prepaid and insured to an Authorized KitchenAid
Service Center. Your repaired Stand Mixer will be returned prepaid and
insured. If you are unable to obtain satisfactory service in this manner, call
toll-free 1-800541-6390 to learn the location of a Service Center near you.
HOW TO ARRANGE FOR SERVICE AFTER THE WARRANTY EXPIRES –ALL LOCATIONS
Before calling for service, please review the Troubleshooting section on
page 7.
For service information in the 50 United States, District of Columbia, and
Puerto Rico, call toll-free
1-800-541-6390.
Or write to: Customer Satisfaction Center KitchenAid Portable Appliances
P. O. Box 218 St. Joseph, MI 49085-0218
Or contact an Authorized Service Center near you.
For service information in Canada, call toll-free
1-800-807-6777.
Or write to: Customer Interaction Centre
KitchenAid Canada 1901 Minnesota Court Mississauga, ON L5N 3A7
HOW TO ARRANGE FOR SERVICE OUTSIDE THESE LOCATIONS
Consult your local KitchenAid dealer or the store where you purchased the
Stand Mixer for information on how to obtain service.
For service information in Mexico,
call toll-free 01-800-024-17-17 (JV Distribuciones) Or 01-800-902-31-00
(Industrias Birtman)
HOW TO ORDER ACCESSORIES AND REPLACEMENT PARTS
To order accessories or replacement parts for your Stand Mixer in the 50
United States, District of Columbia, and Puerto Rico,
call toll-free 1-800-541-6390 Monday
through Friday, 8 a.m. to 8 p.m. (Eastern Time), or Saturday, 10 a.m. to 5
p.m. Or write to:
Customer Satisfaction Center, KitchenAid Portable Appliances, P. O. Box 218,
St. Joseph, MI 49085-0218
To order accessories or replacement parts for your Stand Mixer in Canada, call
toll-free 1-800-807-6777.
Or write to: Customer Interaction Centre KitchenAid Canada 1901 Minnesota
Court Mississauga, ON L5N 3A7 To order accessories or replacement parts for
your Stand Mixer in Mexico, call toll-free 01-800-024-17-17 (JV
Distribuciones) Or 01-800-902-31-00 (Industrias Birtman)
TROUBLESHOOTING PROBLEMS
Please read the following before calling your service center.
- The Stand Mixer may warm up during use. Under heavy loads with extended mixing time periods, you may not be able to comfortably touch the top of the unit. This is normal.
- The Stand Mixer may emit a pungent odor, especially when new. This is common with electric motors.
- If the flat beater hits the bowl, stop the Stand Mixer. See “Beater to Bowl Clearance,” page 12.
Keep a copy of the sales receipt showing the date of purchase. Proof of purchase will assure you of inwarranty service.
If your Stand Mixer should malfunction or fail to operate, please check the following:
– Is the Stand Mixer plugged in?
– Is the fuse in the circuit to the Stand Mixer in working order? If you have a circuit breaker box, be sure the circuit is closed.
– Turn the Stand Mixer off for 10-15 seconds, then turn it back on. If the mixer still does not start, allow it to cool for 30 minutes before turning it back on.
If the problem cannot be fixed with the steps provided in this section, then
contact KitchenAid or an Authorized Service Center:
USA/Puerto Rico: 1-800-541-6390 Canada:
1-800-807-6777 Mexico: 01-800-024-17-17
(JV Distribuciones) or 01-800-902-31-00
(Industrias Birtman)
See the KitchenAid Warranty and Service section on page 4 for additional
details. Do not return the Blender to the retailer – they do not provide
service.
TILT-HEAD STAND MIXER FEATURES
NOTE: This
photo shows the Artisan® Series Stand Mixer. The features on your mixer model
may differ slightly.
ASSEMBLING YOUR TILT-HEAD STAND MIXER
WARNING
Electrical Shock Hazard Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical
shock.
To Attach Bowl
- Tu rn speed control to OFF.
- Unplug stand mixer or disconnect power.
- Tilt motor head back.
- Place bowl on bowl clamping plate.
- Turn bowl gently into clockwise direction.
- Plug into a grounded 3 prong outlet.
To Remove Bowl
- Turn speed control to OFF.
- Unplug stand mixer or disconnect power.
- Tilt motor head back.
- Tu rn bowl counterclockwise.
To Attach Flat Beater, Wire Whip, or Dough Hook
- Tu rn speed control to OFF.
- Unplug stand mixer or disconnect power.
- Tilt motor head back.
- Slip beater onto beater shaft and press upward as far as possible.
- Tu rn beater to right, hooking beater over pin on shaft.
- Plug into a grounded 3 prong outlet.
To Remove Flat Beater, Wire Whip or Dough Hook
- Turn speed control to OFF.
- Unplug stand mixer or disconnect power.
- Tilt motor head back.
- Press beater upward as far as possible and turn left.
- Pull beater from beater shaft.
ASSEMBLING YOUR TILT-HEAD STAND MIXER
To Operate Speed Control
Speed control lever should always be set on lowest speed for starting, then
gradually moved to desired higher speed to avoid splashing ingredients out of
bowl. See page 13 for Speed Control Guide.
To Lock Motor Head
- Make sure motor head is completely down.
- Place locking lever in LOCK position.
- Before mixing, test lock by attempting to raise head.
To Unlock Motor Head
- Place lever in UNLOCK position.
NOTE: Motor head should always be kept in LOCK position when using mixer.
**USING YOUR POURING SHIELD***
To Attach Pouring Shield
- Turn speed control to OFF.
- Unplug stand mixer or disconnect power.
- Attach flat beater, dough hook, or wire whip and bowl (see page 9).
- From the front of the mixer, slide the pouring shield over the bowl until the shield is centered. The bottom rim of the shield should fit within the bowl.
To Remove Pouring Shield
- Tu rn speed control to OFF.
- Unplug stand mixer or disconnect power.
- Lift the front of the pour shield clear of the bowl rim and pull forward.
- Remove attachment and bowl.
To Use Pouring Shield
- For best results, rotate the shield so the motor head covers the “u” shaped gap in the shield. The pouring chute will be just to the right of the attachment hub as you face the mixer.
- Pour the ingredients into the bowl through the pouring chute.
- If Pouring Shield is included.
cakes | biscuits |
---|---|
creamed frostings | quick breads |
candies | meat loaf |
cookies | mashed potatoes |
pie pastry |
Wire Whip for mixtures that need air incorporated:
eggs | sponge cakes |
---|---|
egg whites | angel food cakes |
heavy cream | mayonnaise |
boiled frostings | some candies |
Dough Hook for mixing and kneading yeast doughs:
breads | coffee cakes |
---|---|
buns | buns |
MIXING TIME
Your KitchenAid® Stand Mixer will mix faster and more thoroughly than most
other electric Stand Mixers. Therefore, the mixing time in most traditional
and non-packaged recipes must be adjusted to avoid overbeating. With cakes,
for example, beating time may be half as long as with other Stand Mixers.
TILT-HEAD STAND MIXER USE
WARNING
Injury Hazard
Unplug mixer before touching beaters.
Failure to do so can result in broken bones, cuts or bruises.
NOTE: Do not scrape the bowl while the Stand Mixer is operating.
The bowl and beater are designed to provide thorough mixing without frequent
scraping.
Scraping the bowl once or twice during mixing is usually sufficient.
Tu rn the unit off before scraping.
The Stand Mixer may warm up during use. Under heavy load with extended mixing
time, you may not be able to comfortably touch the top of the unit. This is
normal.
CARE AND CLEANING
Bowl, white flat beater and white dough hook may be washed in an automatic
dishwasher. Or, clean them thoroughly in hot sudsy water and rinse completely
before drying. Wire whip should be hand washed and dried immediately. Do not
wash the wire whip in a dishwasher. Do not store the beaters on the shaft.
NOTE: Always be sure to unplug the Stand Mixer before cleaning. Wipe the
Stand Mixer with a soft, damp cloth. Do not use household or commercial
cleaners. Do not immerse in water. Wipe off the beater shaft frequently,
removing any residue that may accumulate.
BEATER TO BOWL CLEARANCE
Your Stand Mixer is adjusted at the factory so the flat beater just clears the
bottom of the bowl. If, for any reason, the flat beater hits the bottom of the
bowl or is too far away from the bowl, you can correct the clearance easily.
- Turn speed control to OFF.
- Unplug stand mixer or disconnect power.
- Tilt motor head back.
- Turn screw (A) SLIGHTLY counter clockwise (left) to raise the flat beater or clockwise (right) to lower the flat beater.
- Make adjustment so that the flat beater just clears the surface of the bowl. If you over adjust the screw, you may not be able to lock the motor head when it is lowered.
NOTE: When properly adjusted, the flat beater will not strike the bottom or side of the bowl. If the flat beater or the wire whip is adjusted so that it strikes the bowl, the coating may wear off the beater, or the wires on the whip may wear.
SPEED CONTROL GUIDE
Number of Speed
Stir Speed| Stir| For slow stirring, combining, mashing, starting all mixing
procedures. Use to add
flour and dry ingredients to batter, add liquids to dry ingredients, and
combine
heavy mixtures. Use with Ice Cream Maker attachment.
---|---|---
2| SLOW MIXING| For slow mixing, mashing, faster stirring. Use to mix heavy
batters and candies, start mashing potatoes or other vegetables, cut
shortening into flour, mix thin or splashy batters, and mix and knead yeast
dough. Use with Can Opener attachment.
4| MIXING, BEATING| For mixing semi-heavy batters, such as cookies. Use to
combine sugar and
shortening and to add sugar to egg whites for meringues. Medium speed for cake
mixes. Use with: Food Grinder, Rotor Slicer/Shredder, and Fruit/Vegetable
Strainer.
6| BEATING, CREAMING| For medium fast beating (creaming) or whipping. Use to
finish mixing cake, doughnut, and other batters. High speed for cake mixes.
Use with Citrus Juicer attachment.
8| FAST BEATING, WHIPPING| For whipping cream, egg whites, and boiled
frostings.
10| FAST WHIPPING| For whipping small amounts of cream or egg whites. Use with
Pasta Maker
and Grain Mill attachments.
NOTE: Mixer may not maintain fast speeds under heavy load, such as when
the Pasta Maker or Grain Mill attachments are used. This is normal.
NOTE: The Speed Control Lever can be set between the speeds listed in the
above chart to obtain speeds 3, 5, 7, and 9 if a finer adjustment is required.
Do not exceed Speed 2 when preparing yeast dough. This may damage the mixer.
MIXING TIPS
Converting Your Recipe **for the Mixer
The mixing instructions for recipes in this book can guide you in converting
your own favorite recipes for preparation with your KitchenAid Stand Mixer.
Look fo recipes similar to yours and then adapt your recipes to use the
procedures in the similar KitchenAid recipes.
For example, the “quick mix” method (sometimes referred to as the “dump”
method) is ideal for simple cakes, such as the Quick Yellow Cake and Easy
White Cake included in this book.
This method calls for combining dry ingredients with most or all liquid
ingredients in one step.
More elaborate cakes, such as tortes, should be prepared using the traditional
cake mixing method.
With this method, sugar and the shortening, butter, or margarine are
thoroughly mixed (creamed) before other ingredients are added.
For all cakes, mixing times may change because your KitchenAid® Stand Mixer
works more quickly than other mixers. In general, mixing a cake with the
KitchenAid Stand Mixer will take about half the time called for in most
traditional and non-packaged cake recipes.
To help determine the ideal mixing time, observe the batter or dough and mix
only until it has the desired appearance described in your recipe, such as
“smooth and creamy.”
To select the best mixing speeds, use the Speed Control Guide on page 13.
Adding Ingredients
Always add ingredients as close to side of bowl as possible, not directly into
the moving beater. The Pouring Shield can be used to simplify adding
ingredients.
NOTE: If ingredients in very bottom of bowl are not thoroughly mixed,
then the beater is not far enough into the bowl. See “Beater to Bowl
Clearance” on page 12.
Cake Mixes
When preparing packaged cake mixes, use Speed 2 for low speed, Speed 4 for
medium speed, and Speed 6 for high speed. For best results, mix for the time
stated on the package directions.
Adding Nuts, Raisins, or Candied Fruits
Follow individual recipes for guidelines on including these ingredients. In
general, solid materials should be folded in the last few seconds of mixing on
Stir Speed.
The batter should be thick enough to prevent the fruit or nuts from sinking
to the bottom of the pan during baking. Sticky fruits should be dusted with
flour for better distribution in the batter.
Liquid Mixtures
Mixtures containing large amounts of liquid ingredients should be mixed at
lower speeds to avoid splashing. Increase mixer speed only after the mixture
has thickened.
EGG WHITES
Place room temperature egg whites in a clean, dry bowl. Attach bowl and wire
whip. To avoid splashing, gradually turn to designated speed and whip to the
desired stage. See chart below.
AMOUNT SPEED
1 egg white … GRADUALLY to 10
2+ egg whites … GRADUALLY to 8
Whipping Stages
With your KitchenAid® mixer, egg whites whip quickly. So, watch carefully to
avoid overwhipping. This list tells you what to expect.
Frothy
Large, uneven air bubbles.
Begins to Hold Shape Air bubbles are fine and compact; product is white.
Soft Peak
Tips of peaks fall over when wire whip is removed.
Almost Stiff
Sharp peaks form when wire whip is removed, but whites are actually soft.
Stiff But Not Dry
Sharp, stiff peaks form when wire whip is removed. Whites are uniform in color
and glisten.
Stiff and Dry
Sharp, stiff peaks form when wire whip is removed. Whites are speckled and
dull in appearance.
WHIPPED CREAM
Pour cold whipping cream into a chilled bowl. Attach bowl and wire whip. To
avoid splashing, gradually turn to designated speed and whip to the desired
stage. See chart below.
AMOUNT SPEED
1⁄4 -3 ⁄4cup………. GRADUALLY to 10 (60 ml – 175 ml)
1+ cup ……… GRADUALLY to 8 (235 ml +)
Whipping Stages
Watch the cream closely during whipping. Because your KitchenAid mixer whips
so quickly, there are just a few seconds between whipping stages. Look for
these characteristics:
Begins to Thicken
Cream is thick and custard-like.
Holds Its Shape
Cream forms soft peaks when wire whip is removed. Can be folded into other
ingredients when making desserts and sauces.
Stiff**
Cream stands in stiff, sharp peaks when wire whip is removed. Use for topping
on cakes or desserts, or filling for cream puffs.
ATTACHMENTS AND ACCESSORIES
General Information
KitchenAid® attachments are designed to assure long life. The attachment
power shaft and hub socket are of a square design, to eliminate any
possibility of slipping during the transmission of power to the attachment.
The hub and shaft housing are tapered to assure a snug fit, even after
prolonged use and wear. KitchenAid attachments require no extra power unit to
operate them; the power unit is built in.
GENERAL INSTRUCTIONS
To Attach
-
Tu rn the speed control to OFF.
-
Unplug mixer or disconnect power.
-
Loosen the attachment knob by turning it counterclockwise, and remove the attachment hub cover or flip up hinged hub cover.
-
Insert the attachment shaft housing into the attachment hub, making certain the attachment power shaft fits into the square attachment hub socket. It may be necessary to rotate the attachment back and forth.
When the attachment is in proper position, the pin on the attachment will fit into the notch on the hub rim. -
Tighten the attachment knob by turning it clockwise until the attachment is completely secured to mixer.
WARNING
Electrical Shock Hazard Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock. -
Plug into a grounded 3 prong outlet.
To Remove
- Turn the speed control to OFF.
- Unplug mixer or disconnect power.
- Loosen the attachment knob by turning it counterclockwise. Rotate the attachment slightly back and forth while pulling it out.
- Replace the attachment hub cover. Tighten attachment knob by turning it clockwise.
References
- ingredientes.es
- Repair Your Grill: Shop Replacement Parts for 24,880 Models
- Kitchenaid Mixer Parts - Select From 532 Models