kikkaboo Noah Explora Cradle Mattress Instruction Manual

Instruction Manual bed-side crib
NOAH

Noah Explora Cradle Mattress

INSTRUCTIONS FOR USE

IMPORTANT! KEEP FOR FUTURE REFERENCE!
READ CAREFULLY!

WARNING!

1. Do not use this product without reading the instructions for use first.
2. Stop using the product as soon as the child can sit or kneel or pull itself up.
3. Placing additional items in the product may cause suffocation.
4. Do not place the product close to another product, which could present a danger of suffocation or strangulation, e.g. strings, blind / curtain cords, etc.

WARNING!

1. Do not use more than one mattress in the product.
2. Rail must not be higher than the adult bed mattress.
3. To avoid the risk of your child being strangled the attachment system to the adult’s bed shall always be kept away from and out of the crib.
4. Only use the mattress sold with this cot, do not add a second mattress on this one, suffocation hazards.
5. Be aware of the risk of open fire and other sources of strong heat, such as electric bar fires, etc. in the near vicinity of the cot (crib and suspended bed).

• The product should be placed on a horizontal floor.
• Young children should not be allowed to play unsupervised in the vicinity of the crib.
• The crib should be locked in the fixed position when the child is left unattended.
• All assembly fittings should always tightened properly and that care should be taken that no screws are loose, because a child could trap parts of the body or clothing ( e.g. strings, necklaces, ribbons for babies dummies, etc.) which would pose a risk of strangulation. Perform routine checks to make sure there are no loose, damages or missing parts.
• Do not use mattress for the crib different than this, provided with the product and approved by the manufacturer.
• If you use a different mattress from the sold with the crib, please ensure that it is with proper thickness and it is suitable with the crib. The thickness of the mattress chosen shall be such that the internal vertical height (surface of the top of the mattress to the upper edge of the bed sides) is at least 200 mm in the higest position of the bed base.
• If you use a different mattress from the sold with the cot, the length and width shall be such that the maximum gap between the mattress and the sides and ends does not exceed 30 mm.
• The inclination of the crib is allowed with a maximum gap of 2 positions between one foot and other.
• The child’s head should always be positioned on the highest side.
• DO NOT use crib if any parts are missing, damaged or broken. Please, contact our distributors. DО NOT substitute parts.
• The mattress on the parent bed should always be higher than the side of the crib. If not, use the adjusting system to make sure the height is correct on both sides.
• Attachment system is provided with the crib. Do not use other attachment system.
• The bedside sleepers shall never be used in an inclined position.
• To prevent a suffocation hazard from entrapment, the bedside sleeper shall be properly secured to the adult bed using the attachment system.There shall never be a gap between the lower side of the bedside sleeper and the mattress of the adult bed. Check the tightness of the attachment system before each use by pulling the bedside sleeper in a direction away from adult bed.
• If there is any gap between the bedside sleeper and the adult bed DO NOT use product.
• Gaps should not be filled with pillows, blankets or other items.

DANGER! ALWAYS COMPLETELY RAISE THE DROP SIDE WHEN NOT ATTACHED TO THE ADULT’S BED.

• Age of use : 0-6 months , Max. weight 9kg.
• The product is ready for use only when the locking mechanisms are engaged.
• Make sure they are securely fixed before use.
• When your child is unattended in the product in “Crib configuration”, always make sure that the side is raised and the zippers are closed completely.
• Do not use the body of the crib without its frame.
• Assemble, unfold and fold the product ONLY by an adult!
• DO NOT allow children under 3 years of age till fully assemble the product to avoid access to small and disassembled parts!
• Any plastic cover should be removed, destroyed or kept away from children to avoid suffocation.
• Ensure the feet of the crib are fully lengthened when using as a standalone crib.
• Do not use the crib if the height of your bed is less than 54 cm or more than 65 cm above the floor .
• Use of the product is only permitted with beds and/or mattress with straight sides! Use of the product with round beds and/or mattress or water beds or inflatable mattress, etc. IS NOT PERMITTED!
• When the product is use in the “Co-Sleeping mode”( fixing to the bed) it should always be fitted to the long side of access to the bed. DO NOT fix the product to the head or bottom of the bed!

IMPORTANT FOR YOUR CHILD’S SAFETY!

• The “Co-sleeping” function is applicable ONLY with the type of beds that meet all the conditions described above and in this paragraph! In particular the side support of the crib should always be put close to the parent’s mattress and the mattress should always be aligned with the height of the side support for restraint of the crib.

• Furthermore, the crib must be firmly fixed to the structure of the parents bed or to the mattress support ( net or slats).

• When using the product at „Co-sleeping function“, to prevent a suffocation hazard from entrapment, the bedside sleeper shall be properly secured to the adult bed using the attachment system.
  • There shall never be a gap between the lower side of the bedside sleeper and the mattress of the adult bed.

• Check the tightness of the attachment system before each use by pulling the bedside sleeper in a direction away from adult bed.

• If there is any gap between the bedside sleeper and the adult bed DO NOT use product.

• Check to make sure that the crib in the co-sleeping mode does not interfere with the parent’s bed.

• The mattress on the parent bed should always be higher than the side of the crib. If not, use the adjusting system to make sure the height is correct on both sides.

• Before each use, always check that there is no space between the mattress on the parent bed and the wall of the crib. Pull and tighten the attachment system until the permitted state is restored.

• Whenever the side wall is lowered, check that the parent mattress position is not changed!

• When the side wall of the crib is lowered, it should only be used when it is attached to the parent’s bed.

• Use the crib with the wall lowered only in co-sleeping mode.

• The child may get injured if the amplitude of the swing is excessive.

• Suspended cribs may pose risks to other children.

• Other children may pose additional risks (e.g. by swinging the crib excessively).

• Uneven surfaces can cause instability of the product.

• Locate suspended cribs in such a way that there is no risk of swing impact ( e.g. no risk of the child hitting the crib frame, or the crib hitting other furniture).

PARTS

1.  Matress; 2. Mounting strap; 3. Top handrail; 4. Carrycot; 5. Height adjustment lever; 6. Frame leg; 7. Universal wheel; 8. Connecting element; 9. Supporting plastic clip; 10. Baseplate;

ASSEMBLING THE BEDSIDE SLEEPER

2.1. Insert the transverse supporting tube into the plastic joint until you hear a clicking sound.
2.2. Insert the Bracket tube into the plastic joint until you hear a clicking sound.
2.3. Insert the supporting tube into the joint until you hear a clicking sound, then insert iron rod into the bassinet set.
2.6-2.10 Put the ribbon passes through the square hole and fix into D-ring tightly.
2.11. Place the mattress then keep it flat, the bedside sleeper is fully installed.
NOTE! THE BABY COT IS SUITABLE FOR BEDS WITH MINIMUM HEIGHT 54 CM AND MAXIMUM HEIGHT 65 CM.

HOW TO DISASSEMBLE THE DROP SIDE

3.1. Unzip the zipper both sides of guardrail.
3.2. Push the button as indicated by the arrow on the button, then upwards the top rail.
3.3. Remove the ends of the guardrail.
3.4. Take down the guardrail tube and lay it flat.
NOTE! ALWAYS COMPLETELY RAISE THE DROP SIDE WHEN NOT ATTACHED TO THE ADULT’S BED!

HOW TO ADJUST THE HEIGHT HEIGHT SETTING

To change the crib’s height, press the height adjustment levers on both ends of the crib and set the carrycot at the desired height. There are seven crib height settings available. The crib allows setting a different height of each of its ends.
WARNING! The maximum permitted tilt of the crib carrycot is a difference of two setting levels. Always keep the baby’s head in the crib on the higher end of the carrycot.
WARNING! When adjusting the height position , make sure the angle of the inclination of the bassinet base end to end (head to feet) shall not be greater than 10°.0r the difference between left and right gears of height shall be smaller than 2°.
4.1. Lift up the plastic height adjust handle both sides, then it comes higher.
4.2. Lift up the plastic height adjust handle both sides, then pull down the nest, it comes lower as you need.

CONNECTING WITH ADULT’S BED

WARNING! When using the bedside bed function, the drop side rail that must be removed and kept well.
WARNING! When fixing the bedside bed, the short guardrail edge must be closely fitted with the adult mattress to avoid any gap.
NOTE! When used as a bedside sleeper, the carrycot’s bottom must be parallel to the ground. There shall be no difference in height between the crib’s ends.
NOTE! Before each use, make sure there is no gap between the adult’s bed mattress and the side of the crib.
WARNING! This product can only be used with beds and/or mattresses which have straight edges. Do not use this product with any beds and/or mattresses which are rounded or with water beds.
THE TYPE ADULT BEDS WITH WHICH THE BEDSIDE SLEEPER CAN OR CAN NOT BE USED

WARNING! The attachment system must ALWAYS be used in bedside sleeper mode:
5.4. Align the crib directly next to the parent bed and pass the Attachment System underneath the mattress of the bed and around the bed frame.
5.5. Secure the Attachment System by connecting and pass the clip buckles together. Pull strap to tighten the Attachment System securely to the bed.
5.6. Mattress , Box springs & Frame aligned; Acceptable adult bed conditions for co sleeping mode (bed frame in-line).
5.7. Unacceptable adult bed conditions for co sleeping mode (bed frame not in- line).
Not suitable for use next to water beds or children’s beds.

• Let the bedside crib toward to adult’s bed.
• Connect the bedside crib and adult’s bed with strap, the strap have to place between mattress and frame of adult’s bed.

WARNING! When using the bedside bed function, the drop side rail that must be removed and kept well.
WARNING! When fixing the bedside bed, the short guardrail edge must be closely fitted with the adult mattress to avoid any gap. The bedside sleeper can be used for aligned adult bed only. Meanwhile the distance from the lowest bottom side of the aligned adult bed(the drop side) to the ground should be more than 20cm.
5.2 Make sure the foot reach the bed side board.
5.3 Not suitable for use next to water beds or children’s beds.
BEDSIDE SLEEPER FUNCTION
5.1-5.3 To use the product as a bedside sleeper, it needs to be converted. The procedure:

1. Undo the zippers on both ends of the folding side .
2. Slide the locks to release the railing retainer.
3. Lower the folding side of the carrycot.
4. Put the crib to the side of the adult’s bed and set the crib’s height so that the top of the bed’s mattress is level with – or no more than 2 cm above – the top edge of the folding side.
5. Pass the crib’s mounting straps under the bed’s mattress and hook the ends over the adult’s bed frame on the opposite side of the bed. The ends must be upright between the bed frame and the mattress.
6. Secure the mounting straps to the crib using the clasps..
7. Tighten the mounting straps and make sure this keeps the crib stable and firmly attached to the adult’s bed.

HOW TO USE THE BRAKE

6.1. To lock the crib wheels, press down the brake tabs on each of the wheels.
6.2. To release the wheels, lift the brake tabs.

CLEANING AND MAINTENANCE

• Clean the metal and plastic parts with a damp cloth and a mild detergent.
• To clean use soapy water or soft cleaning detergent. Handwash the bag with soapy water. Do not iron. Do not bleach.
• DO NOT place the cot near heating devices because it will damage the plastic and fabrics.
• DO NOT use crib if any parts are missing, damaged or broken. Please, contact our distributors. DО NOT substitute parts.

Materials used: Plastic, textile, metal
PRODUCED FOR KIKA GROUP LTD., VASIL LEVSKI 121, PLOVDIV, BULGARIA. MADE IN CHINA.
COMPLIES WITH EN 1130:2019+AC:2020; EN 16890:2017+А1:2021

Kika Group Ltd.
Vasil Levski 121
4000 Plovdiv, Bulgoria
office@kikkaboo.com
4359 32 515151
KikkaBoo Espofia SL.
Pol. ind. Les Alamos s/n, Fase IL Nave 17
18230 Atarfe (Granada), Espafia
oficina@kikkabeo.com
+34 919 148 299
www.kikkaboo.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>