Kikkaboo i-SIZE Child Car Seat i-Moove Instruction Manual
- June 1, 2024
- kikkaboo
Table of Contents
100-150 cm
car seat
i-Size
INSTRUCTIONS FOR USE
I.
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
IMPORTANT! KEEP FOR FUTURE REFERENCE!
READ CAREFULLY!
The instructions for use must be kept for the entire life of the universal child restraint system.
NOTICE
- This car seat provides optimal safety in all installation positions for which it was designed.
- This is a Universal booster seat Enhanced Child Restraint System (100-150cm). It is approved according to UN Regulation No.129, for use in i-Size compatible and universal vehicle seating positions as indicated by vehicle manufacturer in the vehicle user’s manual. if in doubt, consult the Universal Enhanced Child Restraint System manufacturer or the retailer.
- This is an i-Size Universal Enhanced Child Restraint System, it is approved to regulation No. 129 series of amendments, for general use in vehicles and it will fit most, but not at all, car seats. If in doubt, consult either the Universal Enhanced Child Restraint System manufacturer or the retailer.
- It should be installed in vehicles in which the vehicle manufacturer’s manual states that child restraint systems rated as ‘Universal i-Size’ are acceptable for this age group.
- The product has been approved pursuant to European regulation ECE R129 and can be used for heights between 100 and 150 cm.
- Make sure that the buckle is correctly fastened before starting to drive.
- Any straps holding the restraint to the vehicle should be tight that any support-leg should be in contact with the vehicle floor, that any straps or impact shields restraining the child should be adjusted to the child’s body, and that straps should not be twisted.
- Ensure that any strap or belt that holds the child is not folded or twisted and remains tightened.
- Ensure that the abdominal belt or strap rests as low as possible over the child’s hips, on both sides.
- In the event of an accident, even if there are no apparent damages, the seat may be unsafe. The seat should be replaced after being subjected to the sudden and strong stresses associated with an accident.
- Instruction illustrations are for informational purposes only. The child restraint system may contain small differences compared to the photographs or images in the instruction manual. These variations do not affect its approval by Regulation ECE R129.
- Under no circumstances should the car seat be installed in the car’s passenger seat opposite the direction of travel if there is an active airbag.
- Please read the instructions carefully, as incorrect installation could result in serious injury. In this case, the manufacturer shall not be held liable.
- Ensure that all the locking devices are engaged before use.
- It is dangerous to undertake any changes or additions to the safety seat with approval from the competent authority. It is dangerous to not strictly follow the installation instructions provided by the child car set manufacturer.
- Please never use the safety seat without its cover or without the harness protectors.
- Make sure to protect the child safety seat from direct sunlight as it could heat up and hurt the child.
- The car seat should remain permanently installed in the vehicle, even when the child is not in it. Never leave the child unattended when sitting in the car seat, even when the seat is outside the vehicle.
- Make sure that any luggage or objects that could cause injuries in the event of an accident are fastened securely.
- The cover of the child restraint system should not be replaced with another, unless recommended by the manufacturer, because it is an integral part of the system for securing children!
- It should be installed in cars for which the manufacturer states in its car owner’s manual that the vehicle is suitable for an i-Size Universal Enhanced Child Restraint System for this age range.
- Security is only guaranteed if the child restraint is fitted in accordance with these instructions.
- The manufacturer guarantees the quality of its products, but not the quality of second-hand products or products of other brands.
- Replace child seats or harness accessories that are damaged or have been used incorrectly.
- For the i-Size enhanced child restraint system, the user must read the instructions manual of the vehicle’s manufacturer.
- Don’t use in forward facing before the child reaches the age of 15 months.
- It is important to ensure that any lap strap is worn low down, so that the pelvis is firmly engaged.
- The instruction must be retained on the child restraint for its life period.
- The hard components or plastic parts of safety device for children should be deployed and installed in way that during everyday use of the vehicle not be jammed by the movable seats or doors. Prevent harness/vehicle belt from getting trapped between car doors or rubbing against sharp parts of the seat or body.
- All belts that fix the restraint system to the vehicle must be tightened, all belts retaining the child must be adjusted according to the child’s body. Twisting of the belts shall not be allowed.
- Don’t use another support point of contact except the ones described in the instructions and marked on the child restraint system.
- If the child restraint system offers alternative support point of contact and you consider that using that alternative route is not satisfactory, please contact the manufacturer of the child restraint system.
- Install the child restraint system at the seating positions in the vehicle categorized as I-size in the vehicle owner’s manual by using the primary route of the belt.
- Do not use the car seat in the house. It is not designed for home use and should only be used in the vehicle.
- Before you set any mobile or adjustable part of the child seat you need to remove your child from the child seat.
- Check regularly the belts for wearing by paying special attention to the fixing points, the safety guards and the adjusting devices.
- Do not leave the buckle partially closed, it must be locked when all parts are engaged. You must be able to remove the child from the seat immediately in case of emergency. You have to teach the child not to play with the buckle.
- Keep the child’s chair at a safe place away from children when not in use. Avoid placing heavy objects on the chair. Prevent contact of your vehicle chair with corrosive substances, for example acid from the battery.
NOTICE
Do NOT install in front seats except in these specific cases:
- When the car does not have back seats.
- When all back seats are occupied by children less than or equal to 135 cm tall.
- When it is not possible to install all child restraints in the back seats.
In seats with: ISOFIX anchorages and Top Tether anchor points and 3-point belt (car’s seat belt).
ATTENTION
The child seat must only be used in this seat IF it has ISOFIX anchorages, top tether points a lap and 3 points belt: diagonal (A) and abdominal (B).
Stature
| Size
---|---
100-150cm|
ISO/B2
Read the car manual first and check whether the car seat is equipped with ISOFIX attachment fixed anchor points, and check the size of recommended ISOFIX attachment constraints on the system if it is matched our ISOFIX attachment size.
Produced for Kika Group Ltd., Vasil Levski 121, Plovdiv, Bulgaria. Made in
China.
This product complies with ECE R129.
I. PARTS
- Head pillow;
- Headrest belt;
- Base;
- Angle adjustable handle;
- Headrest adjustment;
- Back of seat;
- ISOFIX attachment
CAR SEAT POSITION NOTICE ( Figure 1 )
Child safety seat must not be used on the position where an airbag has been
activated (airbags can be fatal to children).
Please read the instructions carefully to use the child safety seat properly.
CORRECT DEVICE/SUITABLE WRONG DEVICE/UNSUITABLE DEVICE
ISOFIX ATTACHMENT ( Figure 2 )
The car under the seat anchor point. Read the car manual first and check whether the car seat is equipped with ISOFIX attachment fixed anchor points, and check the size of recommended ISOFIX attachment constraints on the system if it is matched our ISOFIX attachment size.
INTRODUCTION OF PRODUCT FUNCTION I INSTALLING FOR ISOFIX ATTACHMENT ( Figure 3 – 4.3 )
Press ISOFIX attachment side button and push ISOFIX attachment to the end,
align the IISOFIX attachment with ISOFIX attachment anchor and insert, it will
show green if ISOFIX attachment is properly installed. Then pushing the child
seat towards the car seat direction to the end.
(make sure there is no space for the baby car seat and vehicle seat)
ISOFIX attachment anchor ( Figure 4.1 ) , Correct way ( Figure 4.2 ) ,
Wrong way ( Figure 4.3 )
THE INSTALLING METHOD FOR VEHICLE BELT ( Figure 5 )
Warning: Do not use any stress points other than those described in the
documentation and identified on the child restraint system.
Make sure that the belt passes as low as possible in order to better secure
the child’s pelvis.
- Place the baby car seat in vehicle seat and allow your child to sit in the car seat. Pass the belt to the car seat belt guider, and through under the armrest, close the buckle.
- Tighten your seat belt.
ADJUST THE HEIGHT OF HEADREST ( Figure 6 )
Pull up the handle of the seat on the back of head to adjust it from up and down. Release the handle and lock the head position. Attention: Please ensure that the seat head is locked.
10 LEVELS ADJUSTABLE ( Figure 7 )
ADJUST THE RECLINING OF SEAT ( Figure 8 )
Pull adjustable handle to adjust the seat angle. Attention: Pull the handle forward towards the seat.
UNLOCK THE ISOFIX ATTACHMENT ( Figure 9 )
Press the button on the side of the ISOFIX attachment to unlock the ISOFIX attachment. Remove the seat when the ISOFIX attachment on both sides are unfastened.
INSTALLING METHOD FOR THE PRODUCT ( Figure 10 )
Use ISOFIX attachment+ 3-point seat belt to install the child safety seat in forward facing position (Suitable for children 100-150 cm)
- According to point 4.2 to connect ISOFIX attachment and ISOFIX attachment anchor.
- Place the child seat on the car seat and adjust the seat to suitable position. (see page 8).
- Pass the vehicle belt through the belt guider and bypasses the child’s shoulder.
- Pass the vehicle abdomen belt through the abdomen belt guider and bypasses the child’s pelvis.
- Lock the vehicle belt
USE 3-POINT SEAT BELT TO INSTALL THE CHILD SAFETY SEAT IN FORWARD FACING
POSITION
(SUITABLE FOR CHILDREN 100-150 CM) ( Figure 11 )
- Place the car seat on the vehicle seat (make sure that there is no space between the car seat and vehicle seat).Adjust the car seat to the suitable position (see 4.4).
- Pass the vehicle belt through the belt guider and bypasses the child’s shoulder.
- Pass the vehicle abdomen belt through the abdomen belt guider and bypasses the child’s pelvis.
- Lock the vehicle belt
REMOVING THE COVER ( Figure 12 )
Release the headrest rubber band and remove the headrest cover ( Figure 12.1)
Release the back rest cover, then lift the cover from the bottom, and remove it ( Figure 12.2 )
ATTENTION: IF YOU NEED TO INSTALL THE COVER, IT CAN BE REVERSE OPERATIONS.
CLEANING AND MAINTENANCE
In the daily using, it is necessary to regularly check the child safety seat,
In case of accident, the safety seat must be replaced.
When the car seat is not in use, the child safety seat should be placed in a
dry and ventilated place to avoid damp and mildew.
If there is dust on the surface of the child safety seat, we can use a damp
sponge to wipe and ventilate it to dry.
If food or drink drops onto the seat belt by accident, pls remove the seat
belt and rinse thoroughly with warm water and ventilate it to dry.
To clean the entire seat cover, please refer to the washing instructions.
Slight fading may occur during the first washing, which it is a normal
situation.
WASHING INSTRUCTIONS ( PLEASE, REFER TO THE LAUNDRY ICONS BELOW ):
Kika Group Ltd.
Vasil Levski 121
4000 Plovdiv, Bulgaria
office@kikkaboo.com
+359 32 51 51 51
KikkaBoo España S.L.
Pol. ind., Los Álamos s/n, Fase II, Nave 17
18230 Atarfe (Granada), España
oficina@kikkaboo.com
+34 919 148 299
/KikkabooBaby @kikkabooworld /@KikkaBooOfficial