teesa TSA2030 Steam Station Iron Owner’s Manual
- June 5, 2024
- teesa
Table of Contents
teesa TSA2030 Steam Station Iron
Thank you for purchasing TEESA appliance. Please read this operation instruction carefully before use, and keep it for future reference. Producer does not take responsibility for damages caused by inappropriate handling and use of the product.
SAFETY INSTRUCTIONS
In order to reduce the injuries or damages, follow basic safety precautions applied when using any electrical device, including the following:
- Read this instruction manual carefully, even if you are familiar with the appliance. Keep the manual for future reference.
- Before connecting the device to power supply socket, make sure the voltage indicated on the appliance corresponds to the voltage in the power supply socket.
- Place the device on flat, stable surface.
- Clean this device in accordance to instructions listed in “Cleaning and Maintenance” section.
- ALWAYS turn off the device and disconnect it from the mains supply:
- if it’s not operating correctly
- if there’s an uncommon voice when using
- before disassembling the device
- before cleaning
- when not in use
- When you disconnect the power cord of the device, grasp and pull the plug, not the cord/cable.
- Keep the device out of the reach of children. Do not leave children unsupervised with the product.
- This appliance may be used by children who are above 8 years old and by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if they are supervised and guided by a person who is responsible for their safety in a cautious manner, and all the safety precautions are understood and followed. Children should not play with this device. Children should not perform cleaning and servicing of the device unsupervised.
- Fixed power cable may only be replaced in an authorized service point.
- Keep the device and its cord/hose away from heat, water, moisture, sharp edges and any other factor which may damage the appliance or its cord/hose. Do not allow the cord/hose to come into contact with the soleplate when it is hot.
- Protect the product from strong impact and mechanical stress.
- To protect against a risk of electric shock, never immerse the iron in water or other liquids! Do not handle/use it with wet or moist hands.
- Do not use the product for purposes different from displayed in this operating manual.
- Do not leave the appliance unattended when it’s working. ALWAYS disconnect the product from the mains supply when it is not in use.
- Producer of this product is not responsible for damages caused by inappropriate handling and using of the device.
- DO NOT use this product if the power cord, the plug, the steam hose or the device itself shows visible damage, or if the appliance has been dropped, is damaged or leaks.
- Do not attempt to repair this appliance yourself. Only authorized and qualified personnel may repair this device. Never disassemble this device.
- Do not use unauthorized accessories.
- Appliance for indoor and household use only.
- WARNING: Burns may occur from touching hot metal parts, hot water, exposing skin to steam. Exercise caution when operating this device – RISK OF SCALDING!!! Be careful as the released steam is hot and may cause scalds. Do not iron garments while wearing it! WARNING: Never touch hot soleplate before it cools down!
- DO NOT leave the hot iron touching fabrics or inflammable surfaces.
- Do not use unauthorized accessories. The use of accessory not recommended by manufacturer may cause injury to persons or damage to appliance.
- Never fill the water tank with hot water, scent, vinegar, starch, descaler, fabric softener or other chemical reagent. Fill it only with destilled water!
- User can refill water tank at any time during operation, but it is suggested to turn off and disconnect the device from power supply beforehand for safety reasons.
- To avoid a circuit overload, do not operate another high wattage appliance on the same circuit.
- The device should be connected directly to power supply socket (do not use extension cords). This appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.
OPERATION
Power on
Plug the appliance into power supply mains and press power button. The power
indicator will be illuminated, and the low steam level indicator, regarded as
default one, will blink.
Power off
Press and hold the power button, both the power indicator and steam level
indicator will be off.
Temperature knob
Turn the knob to set ironing temperature.
Temperature indicator
When the iron is heating up, the temperature indicator will be illuminated.
Once the iron has reached the selected temperature, it will extinguish.
Steam level control
The steam level can be selected low, medium or high with the steam level
control button. After powering on the device, the low steam level indicator,
regarded as default one, will blink. To change steam level, press the steam
level control button. After few minutes, the indicator will be changed to
constant light. Once the indicator shines constant light, user can press the
steam burst button to emit steam.
Steam burst button
Press the steam burst button, the steam will be emitted from the soleplate as
long as the button is pressed.
Water shortage indicator
If the steam burst button is pressed and hold, but there is not enough water
in the tank, the water shortage indicator will be illuminated within 1 minute
while the button is held pressed. It prompts to add water into the tank.
Filling aperture cap
User can refill water tank at any time during operation, but it is suggested
to turn off and disconnect the device from power supply beforehand for safety
reasons.
If there is not enough water in the tank, grasp the water tank (press the
release button under the tank’s handle at the front of the device) and pull to
detach the tank. Open the aperture cap and fill water. After filling, close
the aperture cap, place the tank in its original place.
Reset button
After the water shortage indicator is illuminated, indicating the water
shortage in the tank, user needs to refill the water tank. After refilling the
water tank with water, press the reset button to make the water shortage
indicator extinguish and then you can release steam for ironing.
Cord clamp
When not in use, the steam hose and power cord shall be stored. Pull out the
clamp first, after winding the cord and the hose around the unit base, push
the clamp back.
Descaling indicator and anti-calc filter
If the descaling indicator illuminates, it indicates the mineral deposits
in the anti-calc filter has been collected to a degree it should be replaced:
- First, power the device off and disconnect it from power supply.
- Grasp the water tank (press the release button under the tank’s handle at the front of the device) and pull to detach the tank.
- Pull the anti-calc filter out (see illustration).
- Replace it with a new anti-calc filter which shall be immersed beforehand into the water for more than one minute.
- Place the tank in its original place, connect the device to power supply and turn it back to operate. Ensure the new anti-calc filter is placed in correct position, if not, the descaling indicator will keep blinking.
IMPORTANT: Do not operate this device with an ineffective anti-calc filter, or without a filter. The pump action of appliance will be impaired and the steam function could fail altogether. WARNING : Do not fill the tank with other liquids than distilled water.
BEFORE FIRST USE
- Remove any sticker, protective foil or storage cover from the soleplate if present.
- Insert a new anti-calc filter which shall be immersed beforehand into the water for more than one minute.
- Connect to power supply and turn the device on. Heat up the iron to maximum temperature and iron over a piece of damp cloth for several minutes for the purpose of removing any residue on the soleplate.
NOTE:
- It is normal that strange odor comes out from the unit during first use. This will cease after a short while.
- Some particles may come out of the soleplate when you use the iron for the first time. This is normal; the particles are harmless and stop coming out of the iron after a short while.
- When you switch on the appliance, the steam generator may produce a pumping sound. This is normal phenomenon.
- During the heating process of the soleplate, there will be little steam coming out from the soleplate automatically and this phenomenon will continue for about 3 seconds. This is normal phenomenon.
USING YOUR STEAM STATION IRON
-
Grasp the water tank (press the release button under the tank’s handle at the front of the device) and pull to detach the tank. Open the aperture cap and fill water. The maximum capacity of water tank is 1,2 l, the water level shall not be exceeded the MAX mark.
-
After filling, close the aperture cap, place the tank in its original place.
-
Put the iron on the thermal insulating cushion.
-
Connect the device to power mains. The device will issue one beep. Then press the power button, the power indicator will be illuminated, and the low steam level indicator, regarded as default one, will blink. User can select other steam level settings by pressing the steam level control button according to requirement. After selection, corresponding indicator will blink. Make sure that there is enough water in the tank.
-
Turn temperature dial to your desired setting, which is depended on the fabric of garment, and temperature indicator will illuminate while heating up.
-
The water in the tank will be heating up. After few minutes, the temperature indicator will be extinguished, which indicates the soleplate temperature has achieved the selected temperature. And when the indicator of selected steam level has been changed from blinking to constant light, it indicates you can take out of the iron and iron the garment with steam function.
Caution:- Do not touch hot soleplate at any time before cooling down!
- Don’t emit the steam directly on people or animals!
-
During operation, if the steam burst button is pressed and hold, but there is not enough water in the tank, the water shortage indicator will be illuminated within 1 minute while the button is held pressed. It prompts to add water into the tank. User should detach the water tank to refill it. After refilling, press the reset button to reactivate the steam release function. Please note: it is possible to refill the tank at any time during use, but it is suggested to turn off and disconnect the device from power supply beforehand for safety reasons.
-
Once you are finished with ironing, press and hold the power button, the device will issue one beep, and the appliance will be turned off and all indicators will be extinguished. Disconnect it from power supply mains.
Vertical ironing
IMPORTANT: Never attempt to perform vertical ironing of fabric a person
is wearing! Do not apply steam near or on a person!
Use the function on hanging fabric: hold the iron in vertical position and
press and hold the steam burst button to emit continuous steam. Bring close
the iron’s soleplate to the fabric and move it slowly over the material.
WARNING: the soleplate after operation will be hot. Never touch it with
bare hand! Place it on the thermal insulating cushion until it cools down
completely.
Note: if there is no steam sprayed out from the soleplate within 10
minutes, the appliance will be turned off automatically.
TEMPERATURE DIAL
IRONING TIPS
-
Always check the ironing instructions on the garment to be ironed. Follow these ironing instructions.
-
The iron heats up quicker than it cools down. Therefore, it is suggested to start ironing the articles requiring the lowest temperature such as those made of synthetic fibers.
-
If the fabric consists of various kinds of fibers, you must always select the lowest ironing temperature to iron the composition of those fibers.
-
Silk and other fabrics that are likely to become shiny should be ironed on the inner side. Velvet and other textures that rapidly become shiny should be ironed in one direction with light pressure applied.
-
Always keeps the iron moving at all times.
-
Pure wool fabrics (100% wool) may be ironed with the steam iron. Set temperature to the one designed for wool, select a high steam position and use a dry ironing cloth over the material.
NOTE: When ironing woolen fabrics, shining of the fabric may occur, so it is suggested that you should turn the article inside out and iron the reverse side. -
Please note, steam functions is not to be used in lowest temperature setting (dripping may occur).
-
Steam ironing eliminates odor and has bactericidal effect. For damp fabrics, use dry ironing.
-
Do not run it over metal objects (such as against the ironing board, buttons, zips, etc.), as it may damage iron’s surface. Iron around any such object.
CLEANING AND MAINTENANCE
- Before cleaning, firstly disconnect the device from power mains and let the appliance cool down completely.
- Wipe flakes and any other deposits on the soleplate with a damp cloth or a non-abrasive (liquid) cleaner.
- NOTE: Do not use chemical, steel, wooden or abrasive cleaners to scrape the soleplate.
- Clean the upper part of iron and the station with a soft damp cloth. Wipe the water drop on the unit base and the thermal insulating cushion with dry cloth.
- NOTE: Before replacing, remember to immerse the new anti-calc filter into the water for more than one minute.
- When do not use the appliance for a long time, pour out the water in the tank, and store the iron on the thermal insulating cushion.
- Wind the steam supply hose and power cord around the unit base and secure it by the cord clamps.
SPECIFICATION
Main features
- Vertical ironing function
- Dry ironing function
- Auto shut-off function (after 10 min.)
- Automatic overheat protection
- Handle covered with non-slip coating
- Detachable water tank
- Temperature indicator
- Water shortage indicator
- Steam indicators (low, medium, high)
- Descaling indicator
- Power indicator
- Anti-calc filter replacement prompt
- Auto reset after descaling
- Steam tube and power cord clamp
Technical data
- Pressure: max. 3,5 bar
- Temperature control: 70°C-225°C
- Steam control: 100 g/min.; 70 g/min.; 40 g/min.
- Steam diffusion: tip and sides
- Heat up time: around 150 sec.
- Soleplate: ceramic
- Water tank capacity: 1,2 l
- Power cord length: 1,8 m
- Steam hose length: 1,5 m
- Power: 2000-2400 W
- Power supply: 220-240 V, 50/60 Hz
- Set includes: steam station iron, anti-calc filter
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate
collection systems) This marking shown on the product or its literature,
indicates that it should not be disposed with other household wastes at the
end of its working life. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, please separate this from other types
of wastes and recycle it responsibly to promote the sustainable reuse of
material resources. Household users should contact either the retailer where
they purchased this product, or their local government office, for details of
where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed with
other commercial wastes for disposal.
Made in China for Lechpol Electronics Leszek Sp.k., ul. Garwolińska 1, 08-400
Miętne. www.teesa.pl
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>