ZKTeco AL10B Digital Lock with Voice Guide User Manual

ZKTeco AL10B Digital Lock with Voice

Safety Precautions

1. The factory setting of all new locks will allow ANY verification to open them.
2. Please register at least one administrator for the newly installed lock. The lock cannot register any normal users without an administrator.
3. The lock is equipped with mechanical keys for manual unlocking. Please keep the mechanical keys at a safe place.
4. To power ON the lock, four alkaline AA batteries (not included) are required. Non-alkaline and rechargeable batteries ARE NOT RECOMMENDED.
5. Do not remove batteries when the lock is in working state.
6. Please replace the battery soon when the lock prompts of low battery.
7. If the lock does not have any activity for seven seconds it will go into sleep mode and prompts of time expired.

Structure

1. Card Area
2. Keypad & Card Detection Area
3. Mechanical Key Hole
4. Handle
5. Battery Area
6. Lockout Switch
7. 9V Battery Interface
8. Speaker

Basic Function

User Introduction

Administrator

| Card| Register / Delete User, Open The Door,

Access in menu

| Max.100
Password| Max.100

Normal User

| Card|

Open the door

| Max.100
Password| Max.100

Note:

1. The maximum card/password capacity is 100 for all groups.
2. The length of the password is six digits.

Initialization
Initializing the lock means all data will be deleted and restored to the factory default setting. Operation steps: Press the reset button on the back body of the lock, then touch the keypad to power on the lock holding the reset button for 5 seconds until the lock prompts the voice of “Restore to default settings, wait a moment”. After around 30 seconds, the lock prompts the voice of “completed”, and then the initialization is finished completely.

Random Password
Random password = Users may enter any number of random digits before or after the correct six-digit password as long as the maximum number of digits entered is 32 or less. For example: If the correct password is 123456, the random password can be 89123456807, 1234562363, 389123456, etc.

Voice Guide
After accessing the menu, the lock provides voice prompts before and after each operation for easy configuration.

Volume Setting
The lock volume can be set, which has three modes, high volume mode, low volume mode, and silent mode.

Language Setting
Supports English / Spanish. or English / Portuguese.

Lockout Mode
When the lock is set as lockout mode, only the administrator can open the door, and also can use the Lockout Switch to enable or disable the mode.

Normal Open
Normal open mode is to keep door always unlocked, which is fit for meeting room and some places free to in or out.

Low Battery Warning
When the lock has a low battery a short beep and voice prompt of “Battery is low, please replace” will be prompted”.

Note:
Access to menu steps is not allowed in low battery status.

9V External Battery

9V external battery is used to open doors in emergency.

Note:
The above battery must be 9V alkaline battery (6LR61).

How To Change Handle Direction

Step

1. Remove the screws with a screwdriver.
2. Take out the lock handle.
3. Turn the handle in the opposite direction.
4. Replace the screws.

Emergency Mechanical Key

The mechanical key is used to open door when the lock has electronic malfunctions.

Note:
Keep the mechanical key at a safe place.

Register First Administrator

Operating Steps

1. Touch the keypad to power ON the lock
2. Press 0 and # to access into menu
3. Enter 3 digit user number
4. Enter password or swipe card
5. Press * to complete
6. Press # to continue registering another user

Note:

1. Put the card on the card area.
2. The length of password should be six digits.
3. Default user number length is three digits, but one or two-digit user numbers are accepted by pressing the # key.
4. Press * to cancel registration before the registration is complete.

Register Other Administrator

Operating Steps

1. Touch the keypad to power ON the lock
2. Press 0 and # to access into menu
3. Verify administrator by card or password
4. Press 1 to register user, and press # to continue
5. Enter 3 digit user number
6. Enter password or swipe card
7. Enter * to complete
8. Enter # to continue registering another admin

Note:
If you verify administrator by password, please end with button #.

Register Normal User

Operating Steps

1. Touch the keypad to power on the lock
2. Press 0 and # to access into menu
3. Verify administrator by card or password
4. Press 2 to register user, and press # to continue
5. Enter password or swipe card
6. Enter * to complete
7. Enter # to continue registering another normal user

Delete Admin

Operating Steps

1. Touch the keypad to power on the lock
2. Press 0 and # to access into menu
3. Verify administrator by card or password
4. Press 3 to delete admin, and press # to continue
5. Enter 3 digit user number
6. Enter * to complete
7. Enter # to continue deleting another admin

Delete Normal User

Operating Steps

1. Touch the keypad to power on the lock
2. Press 0 and # to access into menu
3. Verify administrator by card or password
4. Press 4 to delete user, and press # to continue
5. Enter 3 digit user number
6. Enter * to complete
7. Enter # to continue deleting another normal user

Back-Up Enroll

Operating Steps

1. Touch the keypad to power on the lock
2. Press 0 and # to access into menu
3. Verify administrator by card or password
4. Press 5 to back up enroll, and press # to continue
5. Enter 3 digit user number
6. Enter password or swipe card
7. Enter * to complete
8. Enter # to continue backup another information

Volume Setting

Operating Steps

1. Touch the keypad to power on the lock
2. Press 0 and # to access into menu
3. Verify administrator by card or password
4. Press 6 to set volume, and press # to continue
5. 1. High volume 2. Low volume 3. Silent mode
6. Enter # to confirm

Language Setting

Operating Steps

1. Touch the keypad to power on the lock
2. Press 0 and # to access into menu
3. Verify administrator by card or password
4. Press 7 to set language, and press # to continue
5. 1. English 2. Spanish 3. Portuguese
6. Enter # to confirm

Note:
There are only two language mode, English/Spanish, or English/Portuguese. For example, if the lock is equipped with English/Spanish, selecting “3” (Portuguese), will still show Spanish mode.

Lockout mode

Operating Steps

1. Press 0 and # to access into menu
2. Verify administrator by card or password
3. Press 8 to set lockout mode, and press # to continue
4. 1. Enable 2. Disable
5. Enter # to confirm

Normal open mode

Operating Steps

1. Touch the keypad to power on the lock
2. Press 0 and # to access into menu
3. Verify administrator by card or password
4. Press 9 to set normal open mode, and press # to continue
5. 1. Enable 2. Disable
6. Enter # to confirm

www.zkteco.eu

© Copyright 2014. ZKTeco Inc. ZKTeco Logo is a registered trademark of ZKTeco or a related company. All other product and company  names mentioned are used for

References

• Home | ZKTeco Europe

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>