ZKTeco NG-S101 Series Canales Touch WiFi User Guide
- October 30, 2023
- ZKTECO
Table of Contents
Quick Start Guide
Model: NG-S101/NG-S102/NG-S103
NG-S201/NG-S202/NG-S203
Version: 1.0
Due to the regular upgrades of systems and products, NGTeco could not guarantee exact consistency between the actual product and the written information in this manual.
Important Notes
- If you have any problems, please read this manual carefully or contact Customer Care.
- It’s recommended that a qualified electrician perform the installation, especially if you are unsure about any parts of these instructions.
- This product CAN NOT be used to replace the dimmer switch, 3-way switch or multi-way switch.
- The neutral wire is required for installation.
- Make sure the circuit breaker is turned off before the removal or installation.
- The overall power of all electric connected equipment must not exceed the smart switch’s maximum power.
- Place the device in a secure location away from children’s range.
- The device is only designed for dry indoor areas.
- The device can only connect to 2.4GHz Wi-Fi networks. Make sure that your phone is linked to the 2.4GHz network if you have a dualband router with distinct 2.4GHz and 5GHz networks.
- Make sure that the entered Wi-Fi password is correct when adding a new device.
- Please make sure the device is near to the router for a stable network connection.
- We couldn’t guarantee the exact consistency between the actual product and the written information in this manual due to the regular app and product updates.
Product Overview
Status LED Description:
| Rapid Blinking Green
In Pairing Mode (EZ Mode)
---|---
| Solid Blue
Power On
| Slow Blinking Green
In Pairing Mode (AP Mode)
| Solid Red
Power Off
Note: The above picture is only taken the model NG-S103 as an example, please refer to the actual purchased products.
Installation
Step 1: Remove the Existing Switch
WARNING
Risk of electric shock!
Make sure the power to every switch has been turned off before installation.
- Turn off the power at circuit breaker or fuse box.
- Use an electrical tester to test the power is off before installation.
- Unscrew the existing switch and pull it out from the wall to reveal the wires.
Step 2: Identify the Wires
- Identity the specific wires with some labels.
- Disconnect all of the wires from the existing switch.
Important Note: A neutral wire is required to install the smart switch.
Step 3: Install the New Smart Switch
-
Use a screwdriver to separate the main unit (receptacle) and the faceplate.
-
According to the following wiring diagram, connect the wires to corresponding wire ports.
Wiring Diagram:
-
Carefully insert the main unit into the switch box, and mount it by the screws.
-
Finally, snap the faceplate onto the main unit. When the installation is completed, test each button to make sure the device is wired properly.
Setup
Connecting the Device to NGTeco Home App
Step 1: Download the App and Register Your Account
Search for the NGTeco Home App in Apple App Store or Google Play Store and
download the App to your mobile phone.
Open the NGTeco Home App and log in with your account. If you do not have an
account, create an account with your phone number or Email ID.
Step 2: Power on the Device
Turn on the power of the device. Wait a few seconds until the green LED light
begins to blink rapidly, indicating that the Pairing Mode is active. Note: If
the device does not begin to flashing green, press and hold any button for 5
seconds until the LED light begins to flash green.
Step 3: Add the Device to the App
- Open the app, tap the “+” button on the top right corner of the interface, and then select the ”Add Device” option. Select the ”Electrical” option and then choose the corresponding model purchased.
- Enter the correct password for the Wi-Fi network you’ve selected. Then press the “Next” button.
- Select “Next” if you’ve completed the above steps on the interface.
- You can change the name of the device manually once the notification “Added successfully” displayed on the mobile app. To complete the process, tap the “Done” button.
Important Notes:
The default pairing mode is EZ Mode in the App. If you still failed to connect
your device to Wi-Fi, please try to change to AP Mode to configure the device
again. The operation steps are as follows:
- Make sure the green LED blinks rapidly.
- Press and hold any button for 5 seconds until the green LED light blinks slowly.
- Open the Adding Device interface, tap on the top right corner to change Net Pairing Mode to “AP Mode”, then follow the on-screen instructions to connect the device’s hotspot and complete the setup.
Connecting the Device to Amazon Alexa or Google Assistant
Tap on EDIT Button in the upper right corner of the device interface after
successfully connecting the device to the NGTeco Home App. To link your NGTeco
Home Account to Amazon Alexa or Google Assistant, select the Amazon Alexa or
Google Assistant icon and follow the on-screen instructions.
After completing the setup, you can use the supported voice commands that
include:
- Echo, turn on
. - Echo, turn off
. - Hey Google, turn on
. - Hey Google, turn off
.
Note: Each time when you change the name of the linked device, you must identify it again to update the name.
Product Features
Switch: From any location, turn on or off the device.
Timer: Customize the schedule for the device to turn on or off
automatically.
Countdown: A f te r a s p e c i fi e d a m o u n t o f t i m e, t h e d e v i c
e w i l l automatically turn on or off.
All On/All Off: All the switches will be turned on or off at one time. The model
NG-S101/NG-S201 can’t support this feature.
Multi-Control Association: The same light can be controlled by two or multiple
independent switches (maximum quantity: 4) at the same time, which means that
the associated switches will synchronize the ON and OFF status automatically.
Group Control: Create groups to control multiple devices at one time.
Voice Control: To turn on or off the device, use Amazon Alexa or Google
Assistant voice commands.
Warning:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement:
- This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment.
IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
1600 Union Hill Road Alpharetta, GA 30005
E-mail: service.ng@ngteco.com
www.ngteco.com
Copyright©2022 NGTECO CO., LIMITED. All rights reserved.
Documents / Resources
|
ZKTeco NG-S101 Series Canales Touch
WiFi
[pdf] User Guide
NG-S101, NG-S102, NG-S103, NG-S201, NG-S202, NG-S203, NG-S101 Series Canales
Touch WiFi, NG-S101 Series, NG-S101 Series Touch WiFi, Canales Touch WiFi,
Touch WiFi, Canales WiFi, WiFi
---|---