CHAUVET DJ Shocker Panel 480 LED Strobe User Manual

CHAUVET DJ Shocker Panel 480 LED Strobe

Before You Begin

What Is Included

• Shocker Panel 480
• Power cord

Unpacking Instructions

Carefully unpack the product immediately and check the container to make sure all the parts are in the package and are in good condition.

Claims

If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier= immediately may invalidate your claim. In addition, keep the box and contents for inspection. For other issues, such as missing components or parts, damage not related to shipping, or concealed damage, file a claim with Chauvet within 7 days of delivery.

Text Conventions

Symbols

electrical damage to the product, accessories, or the user.

| Critical installation, configuration, or operation information. Not following these instructions may make the product not work, cause damage to the product, or cause harm to the operator.
| Important installation or configuration information. The product may not function correctly if this information is not used.
| Useful information.

Disclaimer

Chauvet believes that the information contained in this manual is accurate in all respects. However, Chauvet assumes no responsibility and specifically disclaims any and all liability to any party for any loss, damage or disruption caused by any errors or omissions in this document, whether such errors or omissions result from negligence, accident or any other cause. Chauvet reserves the right to revise the content of this document without any obligation to notify any person or company of such revision, however, Chauvet has no obligation to make, and does not commit to make, any such revisions. Download the latest version from www.chauvetdj.com.

Intellectual Property

The works of authorship contained in this manual, including, but not limited to, all design, text and images are owned by Chauvet. © Copyright 2022 Chauvet & Sons, LLC. All rights reserved. Electronically published by Chauvet in the United States of America. CHAUVET, the Chauvet logo, and Shocker Panel 480 are registered trademarks or trademarks of Chauvet & Sons LLC (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. Other company and product names and logos referred to herein may be trademarks of their respective companies.

Safety Notes

• This product is not intended for permanent installation.
• Always connect the product to a grounded circuit to avoid the risk of electrocution.
• Always disconnect the product from the power source before cleaning or replacing the fuse.
• Avoid direct eye exposure to the light source while the product is on.
• Make sure the power cord is not crimped or damaged.
• Never disconnect the product from power by pulling or tugging on the cord.
• If mounting the product overhead, always secure to a fastening device using a safety cable.
• Make sure there are no flammable materials close to the product when operating.
• Do not touch the product’s housing when operating because it may be very hot.
• The voltage of the outlet to which you are connecting this product must be within the range tated on the decal or rear panel of the product.
• The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not expose the product to rain or moisture.
• Always install the product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent surfaces.
• Be sure that no ventilation slots on the product’s housing are blocked.
• Never connect the product to a dimmer or rheostat.
• Make sure to replace the fuse with another of the same type and rating.
• Never carry the product from the power cord or any moving part. Always use the handles.
• The maximum ambient temperature is 104 °F (40 °C). Do not operate this product at higher temperatures.
• In the event of a serious operating problem, stop using the product immediately.
• Do not open this product. It contains no user-serviceable parts.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the product from power via breaker or by unplugging it. Keep this User Manual for future use. If the product is sold to someone else, be sure that they also receive this document.

Introduction

Product Overview

Product Dimensions

Setup

AC Power
The Shocker Panel 480 has an auto-ranging power supply and it can work with an input voltage range of 100 to 240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart. The listed current rating indicates the product’s average current draw under normal conditions.

• Always connect the product to a protected circuit (a circuit breaker or fuse). Make sure the product has an appropriate electrical ground to avoid the risk of electrocution or fire.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the product from power via breaker or by unplugging it. Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel serves only as a 0 to 100% switch.

Fuse Replacement

1. Disconnect the product from power.
2. Using a flat-head screwdriver, unscrew the fuse holder cap from the housing.
3. Remove the blown fuse.
4. Replace with a fuse of the same type and rating.
5. Screw the fuse holder cap back in place and reconnect power.

Power Linking
The product provides power linking via the outlet located in the back of the product. See the diagram below for further explanation.

Power Linking Diagram

You can power link up to 5 Shocker Panel 480 products on 120 VAC or up to 9 Shocker Panel 480 products on 230 VAC. The power linking diagram corresponds to the North American version of the product ONLY! If using the product in other markets, you must consult with the local Chauvet distributor as power linking connectors and requirements may differ in your country or region.

Mounting

Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes.

Orientation

The Shocker Panel 480 may be mounted in any position; however, make sure adequate ventilation is provided around the product.

Rigging

• Before deciding on a location, always make sure there is easy access to the product for maintenance and programming.
• Make sure adequate ventilation is provided around the product.
• Make sure that the structure or surface onto which you are mounting the product can support the product’s weight. (see the Technical Specifications)
• When mounting the product overhead, always use a safety cable. Mount the product securely to a rigging point, whether an elevated platform or a truss.
• When rigging the product onto a truss, use a mounting clamp of appropriate weight capacity.
• When power linking multiple products, mount the products close enough for power linking cables to reach.
• When mounting the product on the floor, make sure that the product and cables are away from people and vehicles.

Mounting Diagram

Operation

Control Panel Operation
To access the control panel functions, use the four buttons located underneath the display. Please refer to the Product Overview to see the button locations on the control panel.

menu option
< UP>| Press to scroll up the list of options or to find a higher value
< DOWN>| Press to scroll down the list of options or to find a lower value
< ENTER>| Press to activate a menu option or a selected value

Menu Map
Refer to the Shocker Panel 480 product page on www.chauvetdj.com for the latest menu map.

DMX Loss

|

LoSS

| hoLd| Holds the last setting when signal is lost
bLAC| Blacks out the product when signal is lost
Auto| Sets the product to automatic mode when signal is lost
Soun| Sets the product to sound mode when signal is lost
Infrared Mode| SEt| oFF| Enables/disables infrared control
on

Configuration (DMX)

The Shocker Panel 480 works with a DMX controller. Information about DMX is in the CHAUVET DMX Primer, which is available from the Chauvet website http://www.chauvetlighting.com/downloads/DMX_Primer_rev05_WO.pdf.

Starting Address and Personality

When selecting a starting DMX address, always consider the number of DMX channels the selected DMXmode uses. If the starting address is set too high, access to some of the product’s channels could berestricted.
The Shocker Panel 480 uses 4 DMX channels, which defines the highest configurable address to 509. For information about the DMX protocol, download the DMX Primer from www.chauvetdj.com. To select the starting address and personality, do the following:

1. Press repeatedly until 4Ch shows on the display.
2. Press .
3. Use or to select the starting address, from d001–512.
4. Press .

DMX Channel Assignments and Values

(when Ch. 2 is 006 ó 255 )

| 000 ó 015| No function
016 ó 255| Pulse, short to long

4

| ****

Strobe effects

(when Ch. 2 is 006 ó 255 )

| 000 ó 005| No function
006 ó 042| 0-100%
043 ó 085| 100-0%
086 ó 128| 100-0-100%
129 ó 171| Random
172 ó 214| Lightning
215 ó 255| Spikes

Configuration (Standalone)

Set the product in one of the standalone modes to control without a DMX controller.

Manual Mode
To run the Shocker Panel 480 at a set dimmer value and strobe speed, do the following:

1. Press repeatedly until U– shows on the display.
2. Press . d _ will show on the display.
3. Use or to increase or decrease the dimmer value, from d 0–255.
4. Press . S _ will show on the display.
5. Use or to increase or decrease the strobe speed, from S 0–255.
6. Press .

Sound-Active Mode
To run the Shocker Panel 480 in sound-active mode, do the following:

1. Press repeatedly until Snd shows on the display.
2. Press .

Sound Sensitivity
To set the sound sensitivity on the Shocker Panel 480, do the following:

1. Press repeatedly until SenS shows on the display.
2. Use or to increase or decrease the program speed, from u001–100.
3. ress . The product will return to sound-active mode.

Configuration (Settings)

DMX Loss
To set what happens when the Shocker Panel 480 loses a DMX signal, do the following:

1. Press repeatedly until LoSS shows on the display.
2. Press .
3. Use or to select from hoLd (holds the last setting), bLAC (blacks out), Auto (switches to an automatic program), or Soun (switches to sound-active mode).
4. Press .

IRC-6 Infrared Remote Control

The Shocker Panel 480 is compatible with the IRC-6 infrared remote control from Chauvet. To run the Shocker Panel 480 in IR mode, follow the instructions below.

1. Press repeatedly until SEt shows on the display.
2. Press .
3. Use or to select from on or oFF.
4. Press .

IRC-6 Operation

Strobe
To adjust the strobe rate with the IRC-6:

1. Press on the IRC-6.
2. Press <+> or <–> to increase or decrease the strobe rate.
3. Press again to turn off the strobe.

Dimmer
To adjust the dimmer with the IRC-6:

1. Press <%> on the IRC-6.
2. Press <+> or <–> to increase or decrease the dimmer.

Black Out
To black out the lights with the IRC-6:

1. Press on the IRC-6.

This will turn off all the lights until the button is pressed again.
NOTE: The IRC-6 will not respond to any inputs when Black Out is activated. If the product does not respond when a button is pressed, try pressing . Black Out may have been activated.

Master/Slave Mode

The Master/Slave mode allows a single Shocker Panel 480 product (the “master”) to control the actions of one or more Shocker Panel 480 products (the “slaves”) without the need of a DMX controller. The master product will be set to operate in either standalone mode or with the IRC-6, while the slave products will be set to operate in slave mode. Once set and connected, the slave products will operate in unison with the master product. Configure the products as indicated below.

Slave products:

1. Press repeatedly until 4Ch shows on the display.
2. Press .
3. Use or to select d 1.
4. Press .
5. Connect the DMX input of the first slave product to the DMX output of the master product.
6. Connect the DMX input of the subsequent slave products to the DMX output of the previous slave product.
7. Finish setting and connecting all the slave products.

Master product:

1. Set the master product to operate in standalone mode or with the IRC-6.
2. Make the master product the first product in the DMX daisy chain.
   • Configure all the slave products before connecting the master to the daisy chain.
   • Never connect a DMX controller to a DMX string configured for Master/Slave operation because the controller may interfere with the signals from the master.
   • Do not connect more than 31 slaves to the master.

Maintenance

Product Maintenance

Dust build-up reduces light output performance and can cause overheating. This can lead to reduction of the light source’s life and/or mechanical wear. To maintain optimum performance and minimize wear, clean your lighting products at least twice a month. However, be aware that usage and environmental conditions could be contributing factors to increase the cleaning frequency.
To clean the product, follow the instructions below:

1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the external surface/vents.
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass cleaner, or isopropyl alcohol.
5. Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.
6. Softly drag any dirt or grime to the outside of the transparent surface.
7. Gently polish the transparent surfaces until they are free of haze and lint.

Always dry the transparent surfaces carefully after cleaning them.
Do not spin the cooling fans using compressed air because it they could be damaged.

Technical Specifications

Dimensions and Weight

Returns

In case you need to get support or return a product:

• If you are located in the U.S., contact Chauvet World Headquarters.
• If you are located in the U.K. or Ireland, contact Chauvet Europe Ltd.
• If you are located in Benelux, contact Chauvet Europe BVBA.
• If you are located in France, contact Chauvet France.
• If you are located in Germany, contact Chauvet Germany.
• If you are located in Mexico, contact Chauvet Mexico.
• If you are located in any other country, DO NOT contact Chauvet. Instead, contact your local distributor. See www.chauvetdj.com for distributors outside the U.S., U.K., Ireland, Benelux, France, Germany, or Mexico. Call the corresponding Chauvet Technical Support office and request a Return Merchandise Authorization (RMA) number before shipping the product. Be prepared to provide the model number, serial number, and a brief description of the cause for the return. To submit a service request online, go to www.chauvetdj.com/service-request. Send the merchandise prepaid, in its original box, and with its original packing and accessories. Chauvet will not issue call tags. Clearly label the package with the RMA number. Chauvet will refuse any product returned without an RMA number. Before sending the product, clearly write the following information on a piece of paper and place it inside the box:
• Your name
• Your address
• Your phone number
• RMA number
• A brief description of the problem Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be your responsibility. FedEx packing or double-boxing are recommended. If you are located outside the U.S., U.K., Ireland, Benelux, France, Germany, or Mexico, contact your distributor of record and follow their instructions on how to return Chauvet products to them. Visit our website www.chauvetdj.com for contact details. Write the RMA number on a properly affixed label. DO NOT write the RMA number directly on the box. Chauvet reserves the right to use its own discretion to repair or replace returned product(s).

Contact Us

Visit the applicable website above to verify our contact information and instructions to request support. Outside the U.S., U.K., Ireland, Mexico, France, Germany, or Benelux, contact the dealer of record.

References

• Service Request - CHAUVET DJ

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>