M-ELEC ML-MRWBB-60-M Wide Body Batten Installation Guide
- June 5, 2024
- M-ELEC
Table of Contents
ML-MRWBB-60-M Wide Body Batten
Installation Guide
Wide body batten
Product information
Our new MR Wide Body Batten has been designed to be fast and flexible. Utilizing a robust 1 piece metal body with integrated end caps, fit-off is exceptionally quick and easy. Multiple entry points enable cables to be run either in from the back of the fitting or the ends to meet up with the large PA16 terminal block. Once the base is mounted and wiring fits off, the diffuser quickly snaps in place without any tools and it’s on to the next job. Just like all of our MR products, the MR Wide Body is supported by our 5-year warranty.
TECHNICAL INFORMATION
| ML-MRWBB-60-M| ML-MRWBB-120-M
---|---|---
Total Power:| 20W| 38W
Lumen Output:| WW 1600lm
NW 1800lm
W 1700lm| WW 3300lm
NW 3700lm
W 3500lm
Colour Temp:| WW 3000K
NW 4000K
W 5700K
IP Rating:| IP40
Efficacy:| WW 80lm/w
NW 90lm/w
W 85lm/w| WW 86lm/w
NW 97lm/w
W 92lm/w
CRI:| 83
Beam Angle:| 130°
Temp Range:| -20° to +45°
Dimmable:| No
Power Supply:| Built-in Driver
220-240V~ 50/60Hz
Average Life:| 50,000 hrs*
Operating current at 240V:| ≤0.12A| ≤0.21A
Input current/inrush| 10.8 A/320uS| 15.7A/304uS
Power Factor:| >0.9
Earth leakage current (mA)| <0.5mA
Dimensions:| 60012460mm| 1200124*60mm
Weight:| 1.18kg| 2.14kg
Warranty:| 5 Years
Kit Includes:| 1x WIDE BATTEN, 1x installation kit
*Total power consumed including driver
** Average life is calculated on expected average lifespan
SURFACE MOUNTED
- Turn the power off before commencing installation.
- Always use suitable fixings for your type of installation.
- Un-clip the end caps on each side of the fitting, squeeze the diffuser in the center to detach and gain access to the internal componentry.
- When running cables into the fitting ensure you use a suitable sealant to prevent any future water penetration.
- Wire MR wide body batten according to the labels on the terminal..
- Select the desired CCT output on the switch
- Re-install the diffuser onto the base and press the end caps in.
- Test and commission.
WIRING GUIDE
SUSPENDED
SPLICING WIRE CONNECTION
PLEASE NOTE
MUST BE INSTALLED BY A LICENSED ELECTRICIAN
- Read instructions carefully before attempting to install the fitting. Retain this guide for future reference
- Disconnect power before installing or servicing
- This fitting is for indoor use and should not be used in areas with limited ventilation or high ambient temperatures
- Do not extend low voltage cables from the output of the power supply
- All components must not be mechanically stressed
- Be careful not to damage or destroy conductive paths on the circuit board
- Follow all relevant electrical and safety standards (including AS3000)
- Correct electrical polarity must be observed as the wrong polarity may destroy the product and is not covered under the warranty
- Damage by corrosion will not be honored as a material defect claim. It is the user’s responsibility to provide suitable protection against corrosive agents such as moisture, condensation, and other harmful elements
T. 1300 222 445 | www.melec.com.au
Data is subject to change, visit our website for up-to-date information
For further information about our Warranties please go to:
melec.com.au/legal/warranties
Version 3