M-ELEC ML-MR8-M-RF 8W Multi LED Downlight User Manual
- June 12, 2024
- M-ELEC
Table of Contents
8W MULTI LED DOWNLIGHT
* With an on-board driver
** Fits under majority of trusses
ML-MR8-M-RF 8W Multi LED Downlight
MR Downlight
ML-MR8-M-RF
Product information
The new MR8-M-RF features a low profile body to allow installation under
trusses and frames while receiving an updated on-board driver with improved
dimming capabilities and a recessed face.
MR8-M-RF includes an IC-4 rating which allows it to rest against, and be
covered with, suitable insulation.
*RAPID version available
5 Year warranty
TECHNICAL INFORMATION
| Total Power: | 8W* |
|---|---|
| Lumen Output: | WW 710Im I NW 7921m I W 737Im |
| Colour Temp: | WW 3000K NW 4000K W 5700K |
| IP Rating: | IP40 Back |
IP54 Front
Efficacy:| 89-105Im/w
CRI:| 80+
Beam Angle:| 110°
Dimmable:| Yes (Triac)
Power Supply:| Integrated
Average Life:| 50,000 hrs**
Standby Current Draw :| 0 . 04A
Double Insulated| Yes
Power Factor| >0 . 9
Dimensions: Base:| Diameter 110mm I Depth 44mm*** I Cut out 90mm
Warranty:| 5 Years
Total power consumed including driver
Average life is calculated on expected average lifespan
Total depth measured from front of mounting surface to top of heat sink
PLEASE NOTE
MUST BE INSTALLED BY A LICENSED ELECTRICIAN
- Read instructions carefully before attempting to install the fitting. Retain this guide for future reference
- Disconnect power before installing or servicing
- All components must not be mechanically stressed
- Follow all relevant electrical and safety standards (including AS3000)
- Damage by corrosion will not be honoured as a material defect claim. It is the user’s responsibility to provide suitable protection against corrosive agents such as moisture, condensation and other harmful elements
- Insulation distance: Building insulation and building elements may abut the luminaire on the sides and/or the top.
- The light source of this luminaire is not replaceable – the whole luminaire should be replaced.
- The flexible cord that is damaged can only be replaced by the manufacturer, its service agent, or a similarly qualified person.
INSTALLATION GUIDE
- Before commencing installation or maintenance, ensure electricity is switched off at the mains
- Remove existing downlight and disconnect old transformer OR for new installations mark and cut out 90 mm hole in ceiling
- Set the desired colour output with the “selector switch” on the back of the downlight head (see picture beside)
- Plug unit into a suitable surface socket OR connect the rapid connector onto the cable
- Carefully bend spring clips upwards and install new LED downlight
MRDownlight
ML-MR8-M-RF-RAPID
Product information
The new MR8-M features a low profile body to allow installation under trusses
and frames while receiving an updated on-board driver with improved dimming
capabilities.
MR8-M includes an IC-4 rating which allows it to rest against, and be covered
with, suitable insulation.
TECHNICAL INFORMATION
| Total Power: | 8W* |
|---|---|
| Lumen Output: | WW 710Im I NW 7921m I W 737Im |
| Colour Temp: | WW 3000K NW 4000K W 5700K |
| IP Rating: | IP40 Back |
IP54 Front
Efficacy:| 89-105Im/w
CRI:| 80+
Beam Angle:| 110°
Dimmable:| Yes (Triac)
Power Supply:| Integrated
Average Life:| 50,000 hrs**
Standby Current Draw :| 0 . 04A
Double Insulated| Yes
Power Factor| >0 . 9
Dimensions: Base:| Diameter 110mm I Depth 44mm*** I Cut out 90mm
Warranty:| 5 Years
Total power consumed including driver
Average life is calculated on expected average lifespan
Total depth measured from front of mounting surface to top of heat
sink
PLEASE NOTE
MUST BE INSTALLED BY A LICENSED ELECTRICIAN
- Read instructions carefully before attempting to install the fitting. Retain this guide for future reference
- Disconnect power before installing or servicing
- All components must not be mechanically stressed
- Follow all relevant electrical and safety standards (including AS3000)
- Damage by corrosion will not be honoured as a material defect claim. It is the user’s responsibility to provide suitable protection against corrosive agents such as moisture, condensation and other harmful elements
- Insulation distance: Building insulation and building elements may abut the luminaire on the sides and/or the top.
- The light source of this luminaire is not replaceable – the whole luminaire should be replaced.
- The flexible cord that is damaged can only be replaced by the manufacturer, its service agent, or a similarly qualified person.
DOWNLIGHT INSTALLATION INSTRUCTIONS
- Before commencing installation or maintenance, please ensure electricity is switched off at the mains.
- Remove existing downlight or mark and cut appropriate hole in ceiling.
- Set the desired colour output with the selector switch on the back of the downlight head.
- Install Rapid ® connector, see next page for instructions.
- Carefully bend spring clips upwards and install the LED Downlight.
- Test.
Follow the below steps to connect the Rapid® connector and downlight to an
input TPS cable.
PLEASE NOTE!
UNIVERSAL POLARITY SAFE.
This product is NOT polarity sensitive.
L & N are interchangable.
UNIVERSAL POLARITY SAVE
-
Slide the cover back until you can remove it completely.
-
For 1.5mm2 cable* place the cable into the channel and push it down so it’s completely flat. OR
-
For 2.5 mm2 cable*, remove the insert in the centre.
-
Place the cable* into the channel and push it down so it is completely flat.
-
Align the lid pins with the channel grooves.
-
Use a steady firm motion and slide the cover closed until you hear a ‘click’ sound.
This indicates the unit is now installed securley. -
OPTIONAL: Fix the rapid connector into place using suitable fixing screws or the cable tie loops.
- Suitable for use with 1.5mm2 and 2.5mm2 2C+E ONLY WITH CENTRE EARTH cables in accordance with AS/NZS 5000.2:2006 conductor range.
TERMINATION GUIDE FOR RAPID® CONNECTOR
- Strip 15mm of the outer cable insulation exposing the inner insulated wires.
- Insert active, earth and neutral insulated cables* into the slots on the terminator block.
- Clip the terminator block in the top end of the channel ensuring the cable* is sitting flat in the channel.
- Place the cover on top of the main body and press the pins firmly into the channel grooves. Slide lid forwards until you hear a ‘click’ sound. This indicates the unit is now installed securley.
UNLOCKING GUIDE FOR RAPID® CONNECTOR
- Insert a small flat bladed screwdriver into position ‘A’ and lift slightly.
- Slide the cover back until you can remove it completely.
Due to our policy of continuous product improvement, we reserve the right to discontinue or update product specifications or designs at any time without notice. Please visit www.melec.com.au for the latest information on our products
T. 1300 222 445 | www.melec.com.au
For further information about our Warranties please go to:
melec.com.au/legal/warranties
FREE
ONSITE WARRANTY
EXCLUSIVE TO
MEMBERS ONL
FFRREEEE OONNSSIITTEE WWAARRRRAANNTTYY FFOORR 33 YYEEAARRSS
IINNCCLLUUDDEESS PPAARRTTSS && LLAABBOOUURR
T. 1300 222 445
www.melec.com.au
For further information about our warranties please go to:
melec.com.au/legal/warranties
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>