698D Lockly Introduces Two New Smart Locks Installation Guide
- June 9, 2024
- LOCKLY
Table of Contents
698D Lockly Introduces Two New Smart Locks
FOR COMMERCIAL USE & PROFESSIONAL INSTALLATION WWW.LOCKLYPRO.COM PGD698D
VISION DUO (698D)
INTERCONNECTED EDITION
INSTALLATION GUIDE
(application in progress)
GET THE MOST OUT OF YOUR LOCKLY GUARDTM
Get the latest user/installation manuals , instructional videos, and FAQs
SCAN or VISIT Locklypro.com/698D
Welcome!
This guide will walk you through step-by-step how to install and get Lockly
GuardTM up and running. Installation generally takes less than 30 minutes. If
you have any questions please call our VIP hotline
855-562-5599 for help.
Reference installation parts overview foldout on back page
Preparation
To complete the installation you will need:
Phillips Screwdriver
Flathead Screwdriver
Tape measure or ruler
Optional
Screwdriver with drill bits
Pliers
Drilling maybe required to install this lock. If you are installing your lock on a brand new door, a drill is required if there are no holes prepared for lock installation. Use provided template to bore holes on door.
3
Preparation continued
Remove existing door hardware, latch or deadbolts before installing the new
lock. Use provided template to bore new holes if needed.
1- 3/8″–2″ (35mm–50mm)
1″ 25.4mm
1″ 25.4mm
2-1/8″ 54mm
4″(101.6mm) or 5.5″(139.7mm)
*Optional
2-1/8″ 54mm
1 Measure and confirm your door is between 1-3/8″ – 2″ (35mm 50mm).
2 Measure and confirm the hole in the door is 2-1/8″ (54mm).
3 Measure and confirm that the backset is be -tween 2 -3/8″ (60mm) to 2 -3/4″
(70mm).
4 Measure and confirm that hole in the door edge is 1″ (25mm).
2-3/8″(60mm) or 2-3/4″(70mm)
5 Measure and confirm that distance between front door holes is 4″(101.6mm) or 5.5″(139.7mm)
IMPORTANT NOTICE * Use goggles to protect eyes if you need to drill door
holes.
4
Step 1
INSTALLING THE LOCKSET
1 Measure the distance between center of front door hole to the edge of your door hole to determine the backset. Adjust latchbolt F and deadbolt J according to the backset of your door.
2-3/8″(60mm) 2-3/4″(70mm)
Deadbolt Adjustment J
b
a
I. Push the crank (a) to extend the deadbolt (b)
c
d
II. Hold the metal plate (c) and twist the deadbolt body (d) clockwise till it snaps to 2-3/8″
c
d
III. To return to default status, while the deadbolt (b) is extended, hold the metal plate (c) and twist the dead bolt body (d) counter-clockwise till it snaps to 2-3/4″
Latchbolt Adjustment F 2-3/8″ (60mm) (a)
Push the shaft (a) to adjust the lockset to 2-3/8″(60mm) or 2-3/4″(70mm).
2-3/4″ (70mm)
Note: the shaft’s horizontal and vertical aligment must be sustained during installation to ensure latch will fully extend and lock securely.
5
Step 1 continued
INSTALLING THE LOCKSET
2 After adjusting the latchbolt F , determine the orientation of the
latchbolt.
Determine the orientation of latchbolt. Facing the door exterior, install the
latchbolt according to the opening direction of your door.
LEFT OUT-SWING DOOR
Inside
RIGHT OUT-SWING DOOR
Inside
Outside
Outside
LEFT IN-SWING DOOR
Inside
RIGHT IN-SWING DOOR
Inside
Outside
Outside
3 Install deadbolt J (top) and latchbolt F (bottom) to door and secure
with screws K and G . Retract deadbolt, make sure bore hole is horizontally
positioned and the spindle shaft is centered.
PGA018
J
PGA019 PGA019S K
G
F
5.5″
4″
For mortise slot
Optional: Stainless steel mortise slot cover, 4″ or 5.5″ Face Plates available. To purchase, please call our Customer Service hotline 855-562-5599 or email prosales@Lockly.com
6
Step 2
CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
The lock ships with handle default for right in-swing or left out-swing door. Check the diagram below if you are unsure of you door orientation.
RIGHT IN-SWING DOOR
INTERIOR
LEFT IN-SWING DOOR
Hinge Side
LEFT OUT-SWING DOOR
EXTERIOR
RIGHT OUT-SWING DOOR
No need to change door handle orientation. Skip Step 2.
LEFT-IN SWING and RIGHT OUT-SWING DOORS require changing the door handle orientation. Continue to follow Step 2 to change exterior and interior door handle orientation.
Changing the Exterior Handle Orientation
1
2
R
(Right handle)
Insert key and rotate so that the two white dots align as shown.
Use the provided pin insert R to push the metal pin located at the 3 o’clock of the the base handle, then the other pin at 9 o’clock position. Remove the handle once the pins are compressed.
7
Step 2 continued CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
3
4
Rotate the handle 180° to the other side of the lock.
Using your fingers, press the two pins located on the left and right side of
the the lock to insert the handle back onto the lock.
Confirm that your installation was complete by checking if the pins are flush against the handle, and has popped out. Adjust the handle accordingly to make sure the pins are fully decompressed and sits flush against the surface.
5
6
Check that your handle works smoothly by giving it a turn up and down.
Twist key back to horizontal position. The key can be taken out once it goes back to the horizontal position.
8
Step 2 continued CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS 7 At the back
of the exterior assembly, remove the screw on point “R”.
8 Align the screw hole on point “L”
then insert the removed screw and tighten.
9
Step 2 continued CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
Changing the Interior Handle Orientation
1
Remove the handle retaining screw and detach the handle. Rotate the handle
180° as shown.
2
Insert the handle retaining screw and tighten using a screw driver. 10
Step 3
PREPARING LOCK FOR INSTALLATION
Carefully prepare the lock and ensure the required parts ( C , D , E ) have
been properly attached before installing to door.
E
4
Slotted Barrel Extension E should be installed according to upper door hole
distance to the bottom door hole (4″ or 5.5″). Use a flathead screwdriver to
secure tighten E clockwise.
1
2
3
Install Spindle C with the holes side into the base of the lock and align the holes locate in the 3 o’clock and 9 o’clock position.
D
Insert locking pin D in to the hole as shown above.
11
Carefully bend the end of the locking pin D with a needle nose pliers.
Failure to bend the locking pin and turn the handle freely without obstruction
will result to malfunction.
Step 4 1 Install fire shield N1 as shown.
N1
INSTALLING THE LOCK (EXTERIOR) N1
N1
Note: The fire hood should not press the wire.
2 Use a screwdriver to secure the cables in the fire hood.
Ensure that the cables are routed out of the U-shaped slot and the fire hood
does not press cables.
Exterior
N2
3 Pull the connecting wire in the
direction of the arrow.
12
4 Install the fire shield N2 on
the outside of the door, on the deadbolt J .
Step 4 continued
Exterior
INSTALLING THE LOCK (EXTERIOR)
6 Ensure E is securely installed on the correct position, then insert E to top
door hole, passing through below part J E
B
5 While aligning the lock straight up-and-down, pass the wiring cable under
the latchbolt F then ensure the Slotted Barrel Extension E passes through the
hole on the lower part of the deadbolt J body as shown.
Exterior
C
7
Pass the spindle C through the center of the latchbolt, and the round rods
through the sides in their respective holes. The cable should run underneath
the lockset.
8 Check lock alignment and ensure that it is sitting flat and aligned straight.
13
Step 5
INSTALLING INTERCONNECTION PLATE GEAR
1 Select interior cover plate U1 or U2 according to door hole distance
and install on to door.
U1
U2
4″(101.6mm) 5.5″(139.7mm)
4″ use cover plate
5.5″ use cover plate
2 Insert Positioning Rods V into the holes to the left and right of the
Spindle
C . The holes are located at the 3 o’clock and 9 o’clock positions.
C
V 14
Step 5 continued
INSTALLING INTERCONNECTION PLATE GEAR
3 Install fire shield N1 as shown. Ensure that
the cables are routed out of the U-shaped slot and the fire hood does not
press cables.
N1
4 Ensure the rods on interior cover plate U1 or U2 is inserted on the
holes of the deadbolt. and the cable and spindle C passed through part U .
U1 or U2
C 15
Step 5 continued
INSTALLING INTERCONNECTION PLATE GEAR
5 Secure interior cover plate U with screws O . Remove the position rods
V and replace them with screws O Tighten clockwise until the mounting
plate is secure.
Hole for O1 or O2 screw for 5.5″
O
Secure with O1 or O2
Hole for O1 or O2 screw for 4″
V
Remove the position rods V and replace them with screws O Tighten clockwise
until the mounting plate is secure.
O1
KM4 x 25mm, for door thickness, 1-3/8″~1-2/3″(35~43mm)
O2
KM4 x 32mm, for door thickness, 1-2/3″~2″(43~50mm)
16
Step 5 continued
INSTALLING INTERCONNECTION PLATE GEAR
6 Select the side of the interconnection gear P according to door handle
orientation Left or Right . Insert torque blade AD to plate according the
distance between the latchbolt and deadbolt .
P
Insert AD for 5.5″
AD
Insert AD for 4″
You may strike AD with pliers to insert it to 4′ or 5.5″ hole.
Select the correct side of the interconnection gear.
For right swing door
For left swing door
The R side should be facing in front of The L side should be facing in front
of you after inserting the torque blade you after inserting the torque blade
17
Step 5 continued
INSTALLING INTERCONNECTION PLATE GEAR
7 Install interconnection plate P onto door. Ensure the torque blade AD
is inserted horizontally to the deadbolt. The spindle must pass through the
plate. Secure the plate with screws M .
AD
P
M X3
18
Step 6
INSTALLING INTERIOR ASSEMBLY (N)
1 Connect cable A1 to A2 by hand. Plug B1 into B2 , match red side of plug with red on socket – insert tightly.
X
AE C
Secure the lock interior with 3 screws AE
Do not touch pins inside* Call our Customer Care Hotline
669-500-8835, for help if the pins are
not centered or bent.
B1
B2
A1
A2
19
Step 6 continued
INSTALLING INTERIOR ASSEMBLY (N)
2 Align the spindle C to the lock interior and attach the Interior lock to
the interconnection plate. Gently push some of the excess cable through the
rectangular hole into the door. Place the remaining cable inside the interior
assembly and ensure it sits securely onto the interconnection plate gear.
X
AE C
Make sure the cable is away and not tangling with the spindle C
Install Cable
IMPORTANT:
1
If you need to disconnect this cable,
use a screwdriver to hold down the
tab before carefully unplugging. DO
NOT FORCE as this may result in dam-
aging the lock.
Remove Cable 2
20
Step 6 continued
X
INSTALLING INTERIOR ASSEMBLY (N) Q
3
Insert 8 AA batteries into the lock by aligning the positive (+) and negative
(-) markings on the batteries to the battery chamber.
4
Secure the battery by sliding the cover Q over the lock and turning the screw
clockwise on top until tight.
21
Step 7
PREPARING DOOR SENSOR FOR INSTALLATION
Do not mount (install) door sensors yet. You will install in step 9.
About door sensors Door sensors provide real-time door condition status, such
as the ability to verify if the door is securely closed. It also sends push
notifications to your phone whenever your door opens and enables voice
control.
Lockly GuardTM Vision Duo (698D) comes with a pre-wired door sensors
consisting of two parts:
Part AA – Wired Sensor
Part AB – Sensor Magnet
IMPORTANT: Gap must be less than 3/4″ when installed. When installed on door,
the distance between the wired sensor and sensor magnet must be less than 3/4″
in order for the sensor to work. If door frame is higher than door, add
included foam pads to level parts AA and AB with each other as much as
possible.
TIPLockly door sensors comes in Grey (PGA061) and Matte Black (PGA062) that
can be ordered through our customer hotline:
855-562-5599 or by email:
prosales@lockly.com
Removal of Sensor (optional) There may be circumstances where the sensor
cannot be installed because of molding/door limitations or is not
aesthetically desirable. The sensor wired to the lock is removable by
carefully pulling its connector from the circuit board. If removed, some
features and functionality will not be available, such as real-time condition
status.
22
Step 7 continued
PREPARING DOOR SENSORS FOR INSTALLATION
When you are installing the door sensors, make sure the arrow of the wired sensor AA is placed next to the arrow of the sensor magnet AB as close as possible.
OR
LEFT
RIGHT
IMPORTANT: Do not install the sensor close to the strike plate H . H
AA AB
H
2-3/8″ (60mm)
< 3/4″ (< 20mm)
EVA
AA AB
23
2-3/4″ (70mm)
If needed add Foam Pads to level AA & AB as much as possible.
Step 7 continued
PREPARING DOOR SENSORS FOR INSTALLATION
The interior assembly comes with the pre-installed wired door sensor setup for
a right/left swing doors with 2-3/4″ (70mm) backset*.
Trim excess part e for doors with 2-3/8″ (60mm) backset as shown below.
AA e
Trim excess here for 2 ” (60mm) backset*.
R
L
*Backset – measure the distance of the door edge to the center of the door hole. Make sure you install the Door Sensor indoors on a clean and dry surface. Gently wipe the surface of your door and door frame where you wish to install the Door Sensor and make sure it’s dry before installing. Keep the Door Sensor away from direct sunlight, high heat locations and large metal objects that may interfere with wireless signals.
DO NOT INSTALL THE SENSORS YET
24
Step 8
INSTALLING THE DOOR STRIKE
It is recommended that you use the included strike plate. However, if you find the deadbolt and latchbolt works with your existing strike plate free of any binding or resistance you can use it. Regardless of which strike plate used, deadbolt and latchbolt needs to operate smoothly, free of any binding or resistance. Adjust appropriately as needed.
K1(2X) L1 L
K (2X)
G (2X) H
J
IMPORTANT: Check the alignment of
the screw holes of both latchbolt and
strike. Ensure the latchbolt plunger is
against the strike plate H .
F
F
H
Make sure the slanted side of Latchbolt F is closing against the slanted part of Strike Plate H .
L
AF or AG Before fixing it on to door frame, check the gap between door and
door frame should be less than 4.5mm. Attach AF (2mm) or AG (3mm) to the
strike plate L to reduce gap, if necessary.
25
Step 9
INSTALLING THE DOORS SENSOR
Make sure you have prepared the door sensors for installation according to Step 7
1 Peel off the paper layer of the
adhesives from the back of the wired sensor AA .
2 Position the wired sensor AA to
the edge of the door, avoiding the door strike plate. Attach and secure with
the adhesives.
2-3/4″ 70mm
2-3 4″(70mm)
2-3/8″ 60mm
3 Close the door. Before you peel off
the paper layer of the adhesives from the sensor magnet AB , align the arrow
with the wired sensor AA . Install AB on to door frame.
2-3 8″(60mm)
The arrows must be aligned or as closed as possible (less than
NOTE:
3/4″). If needed, adjust the position of the sensor magnet using provided foam pads to ensure the Lockly logo blinks red when
door opens or closes.
26
Step 10 DOWNLOAD LOCKLYPRO APP & UNIQUE ACTIVATION CODE
Congratulations! You have completed the Lockly GuardTM Vision Duo (698D)
physical lock installation. To complete your setup, download the LocklyPro app
from the iOS or Google Play app Store and follow on-screen instructions.
Scan or visit Locklypro.com/app
PRO
ACC20220326
Additionally, you’ll need the Activation Card with unique pre-paired QR code to your lock. The card is located in the packaging that your lock came in. This QR code can also be found at the bottom of Vision Connect Hub. Please keep it in a safe place–this QR code is required to complete the setup and will be required if you lose your smartphone or access code.
KEEP THIS CARD!
ACTIVATION CARD
LOCK SERIAL PGDxxxxxxxxxx
ACTIVATION CODE xxxxxxxx
SCAN & SAVE
LOCKLYPRO.COM | HOTLINE: +1 855 562 5599 | EMAIL: PROSALES@LOCKLY.COM
IMPORTANT: Without the QR code you will not be able to reset your lock
27
Step 11
SETTING THE VISION CONNECT HUB
The Vision Connect Hub connects directly to your Wi-Fi router using the
provided LAN cable. Choose an appropriate location for the hub for optimum
performance (see below). For optimum connectivity, it is recommended to set up
the hub LESS than 100 feet (30 meters) away from the lock, and elevated 3 feet
(1 meter) off the ground.
During the setup process position yourself between the lock and the Vision
Connect hub–ideally no more than 100 feet (30 meters) apart. Ensure your iOS
or AndroidTM device has both Bluetooth® and Wi-Fi enabled
Lockly Guard Smart Lock You
Vision Connect
Wi-Fi Router
100 Feet (30 meters) or less
3 feet (1 meters) off the ground
TIP: Sometimes distances between hub and lock can vary due to circumstances.
If you are having difficulty setting up optimal range of 100/ft or less, we’re
here to help. Call our customer care team:
855-562-5599 or by email:
prosales@lockly.com, or visit http:// locklypro.com/support for suggestions
and troubleshooting tips.
28
Step 11 continued
SETUP THE VISION CONNECT HUB
Plug the Wi-Fi Hub into the 5V 1A USB AC adapter and plug the AC adapter to your wall socket.
To enable video doorbell, live monitoring and voice control with Hey Google , you will need to setup the included Vision Connect Wi-Fi hub with the Lockly GuardTM deadbolt smart lock + video doorbell.
VISION CONNECT OVERVIEW
Antenna
LED status lights
LAN cable
Power adapter
Reset TF card
Once you have confirmed that your Wi-Fi Hub is ready to connect to your lock, open the LocklyPro App from your smartphone. Make sure you are standing between the Wi-Fi hub and Lockly Guard smart lock, then Add New Device and follow the on screen instructions.
IMPORTANT: Vision Connect stores recorded video on the included TF card. Although the TF card is discrete, it is recommended to locate it in a discrete or secure area to protect your privacy and video recordings.
29
Step 11 continued
Ensure the TF card that comes with Vision Connect is properly inserted.
SETTING THE VISION CONNECT HUB
Connect LAN cable to closest Wi-Fi router to the Lockly GuardTM lock (100ft).
Always keep the Antenna on UP position
TF card (included, inserted)
Connect power cable and plug USB power adapter into outlet.
LAN cable (S) (included)
Wait 2 minutes for hub to self calibrate. Once LEDs turn RED and blink yellow.
Vision Connect is now ready to connect to your iOS or AndroidTM device.
See troubleshooting on next page if LEDs do not meet the described conditions.
30
Step 12
PAIR LOCKLY GUARDTM VISION LOCK TO APP
Launch the LocklyPro App and select “add a new device”, then select Lockly
GuardTM Vision Duo (698D). You will be prompted to scan the QR code from the
Activation Card or Vision Connect Hub (located at the bottom).
KEEP THIS CARD!
ACC20220326
ACTIVATION CARD
LOCK SERIAL
PGDxxxxxxxxxx
PRO
ACTIVATION CODE xxxxxxxx
SCAN & SAVE
LOCKLYPRO.COM | HOTLINE: +1 855 562 5599 | EMAIL: PROSALES@LOCKLY.COM
OR
LOCKLYPRO App
IMPORTANT: Make sure your Lockly GuardTM Vision has the latest firmware. Allow
updates and follow instructions if prompted. For more info, visit:
http://www.locklypro.com/support
NOTE: Power interruption during firmware update may damage the Vision Connect
hub. Do not interrupt or turn the power off while firmware update is in
progress.
TIPS: · Remember to register for warranty. · Allow your mobile phone to
receive push notifications. · Send in-app feedback if you encounter any issues
while using the App. · If you are having difficulty scanning the QR code,
we’re here to help. Call our customer care team:
855-562-5599, or visit http://
locklypro.com/support for suggestions and troubleshooting tips.
31
Step 13
VISION CONNECT STATUS & TROUBLESHOOTING
During Setup
LED INDICATORS Solid red ON
HUB
After connecting LAN cable and power adapter, wait for 2mins for Vision
Connect to self calibrate.
STATUS
Power ON/ Successfully paired
Yellow slow blinking
Network connected
READY TO CONNECT
If you experience any of the following, power down and disconnect hub, repeat connection process
Red slow blinking
Pairing / Network NOT yet connected
Red fast blinking
Pairing unsuccessful
Yellow OFF
Blinking red goes to blue, then turns OFF
Router or LAN cable issue NO network connection
Resetting
During Firmware Update
Blue slow blinking
Update in progress*
Blue ON Blinking from red to blue
Update Successful Update has failed
*Power interruption during firmware update may damage the Vision Connect hub. Do not interrupt or turn the power off while firmware update is in progress.
32
Step 14
CONNECTING YOUR LOCKLY GUARDTM VISION DUO (698D)
The App will take you through the following steps, make sure the smart lock has been properly installed. You will need your activation card that is included in the box to proceed.
ADD NEW DEVICE
Select A Device
Connect Vision Connect Hub
AT&T
9:41 AM
100%
AT&T
9:41 AM
Select a Device
100%
AT&T
9:42 AM
100%
Connect Vision Connect Hub
AATT&&TT
9:432 AM
110000%%
Connect Vision Connect Hub
AT&T
9:43 AM
100%
Turn to the next page
33
Step 14 continued CONNECTING YOUR LOCKLY GUARDTM VISION DUO (698D)
Find fhe Activation Card
AT&T
9:44 AM
100%
Scan the QR Code
AT&T
9:44 AM
100%
Scan the QR Code
AT&T
9:45 AM
100%
ACC20220326 ACC20220326
PRO
CARD!
TIPDTornteo’patilctldaooiWectsdIeenlifitekthytaifehoowyseuuyitolthloAawtbiushcreneriitKsseiDAvrmcerrEarseCqoiihLtvEsqOiudsCioTeupPKAiieILrnnriYVer’PC,PogesRLCdTOGyAAOTfd.LCDtCooCyHIOhiiTTxfcKVMtudoIxeoIVy|eSIxxOAeuAHwoxExScsTnOTrxxRuTIeNCiaLxxOsIlIIlANlxxtoeNOarElLxx:onduCc+CxxrN1aosxxpd,Ok8eO5stDp.5.CyE5bliyP6Deot2Ae’ol5suea5ERu9ra9astSr|DheCCLbsEsAoMeelmNAcAecIL&oo:skaPRSttRnnolAoOryDtVSltApryEarLeGEehSct@suhotLtOheainCunitKrseLsgdYy.Ccio.oOmyaMTruohrmArdeulceo’iAlcnldcechikaasta.istvsveaCaelytfoieo.dne.
NPeleedasHeevlpis?it https://www.locklypro.com/support/
KEEP THIS CARD!
ACTIVATION CARD
LOCK SERIAL PGDxxxxxxxxxx
ACTIVATION CODE xxxxxxxx
SCAN & SAVE
LOCKLYPRO.COM | HOTLINE: +1 855 562 5599 | EMAIL: PROSALES@LOCKLY.COM
ACC20220326
LOCKLYPRO App
KEEP THIS CARD!
ACTIVATION CARD
LOCK SERIAL PGDxxxxxxxxxx
ACTIVATION CODE xxxxxxxx
SCAN & SAVE
LOCKLYPRO.COM | HOTLINE: +1 855 562 5599 | EMAIL: PROSALES@LOCKLY.COM
OR
If you can’t scan LOCK SERIAL, Then enter manually
AT&T
9:44 AM
100%
Input Activation Code
AT&T
9:45 AM
100%
ACC20220326
KEEP THIS CARD!
ACTIVATION CARD
LOCK SERIAL PGDxxxxxxxxxx
ACTIVATION CODE xxxxxxxx
SCAN & SAVE
LOCKLYPRO.COM | HOTLINE: +1 855 562 5599 | EMAIL: PROSALES@LOCKLY.COM
Turn to the next page
34
Step 14 continued CONNECTING YOUR LOCKLY GUARDTM VISION DUO (698D)
Set the Admmin Code
AT&T
9:46 AM
100%
Match Admmin Code
AT&T
9:46 AM
100%
Successfully Connected
AT&T
9:47 AM
100%
Successfully Connected
AT&T
9:48 AM
100%
Congratulations! Your Lockly GuardTM Vision Duo (698D) is now – set up.
You may proceed to Add the Door Sensors.
35
FCC Warning This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: – Reorient or relocate the receiving antenna. –
Increase the separation between the equipment and receiver. – Connect the
equipment into an outlet on a circuit different from that to
which the receiver is connected. – Consult the dealer or an experienced
radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
FCC Radiation Exposure Statement This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled environment. It should be
installed and operated with minimum distance 20cm between the radiator & your
body.
IC WARNING This equipment contains licence-exempt transmitter(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions: (1) This device
may not cause interference. (2) This device must accept any interference,
including interference that may
cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement économique Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes:
1. L’appareil ne doit pas produire de brouillage; 2. L’appareil doit accepter
tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
IC Radiation Exposure Statement This equipment meets the exemption from the
routine evaluation limits in section 2.5 of RSS-102. It should be installed
and operated with a minimum distance of 20cm between the radiator and any part
of your body.
Cet équipement est conforme à l’exemption des limites d’évaluation habituelle
de la section 2.5 de la norme RSS-102. Il doit être installé et utilisé à une
distance minimale de 20 cm entre le radiateur et toute partie de votre corps.
WARNING: This product can expose you to chemicals including Lead, which is
known to the State of California to cause cancer. For more information go to
www.P65Warnings.ca.gov.
INSTALLATION OVERVIEW & PARTS LIST
This lock can be installed for both right swing and left swing doors. The lock ships ready for a right swing door installation. If you wish to change the orientation of the lock for a Left Swing door, follow instructions on Installation Guide (Step 2).
Battery Cover
Q
AE 3x
BM4 × 24MM Screw
X Interior Assembly
M 3x
PM5 Screw
P Interconnection Plate
O1
KM4 x 25mm, for door thickness, 1-3/8″~1-2/3″(35~43mm)
O2
KM4 x 32mm, for door thickness, 1-2/3″~2″(43~50mm)
AD Torque Blade
O 3x
KM4 Screw
U Interior Cover Plate ( U1 4″ / U2 5.5″)
2-3/8″ (60mm)
2-3/4″ (70mm)
Exterior
Measure distance between the center of the hole to the edge of door, adjust latch F to 2-3/8″(60mm) or 2-3/4″(70mm)
N2 Fire Shield
E Slotted Barrel Extension B Exterior Assembly
Sensor AB Magnet
AA Wired Sensor
KA4 x 20MM Screw K
4x
AC
Deadbolt Strike Plate L
Foam Pads
ST5 x 70MM Screw K1
Deadbolt J
strengthen Strike Plate L1
AF
AG
Strike Plate Spacer (optional)
C Spindle D Locking Pin
F Latch G 4x KA4 x 20MM Screw H Latchbolt Strike Plate
N1 Fire Shield 2x
LAN Cable Y2
A Keys
Y Vision Connect Hub
W
T TF Card
Activation Card
B1 Doorbell Decal B2
Z Power Adaptor
Y1 Power Plug
N Touchscreen Cover (PGA717)
R
Clamping Tool
For changing
handle orientation
V
Positioning Rod For
2x
installing mounting
plate (U)
S
RFID Card
KEEP THIS CARD!
ACTIVATION CARD
LOCK SERIAL PGDxxxxxxxxxx
ACTIVATION CODE xxxxxxxx
SCAN & SAVE
LOCKLYPRO.COM | HOTLINE: +1 855 562 5599 | EMAIL: PROSALES@LOCKLY.COM
ACC20220326
WAIT.
IMPORTANT NOTES
Lockly Guard installs differently from other door locks. Professional
installer(s) and locksmiths must read and follow Lockly Guard installation and
user manuals to prevent damaging the product. Failure to do so may also result
in the smart lock not responding correctly to lock and unlocking commands and
will require re-installation.
This product is recommended for residential use. Please check your office
building or property management policies and regulations before installation.
DO NOT RETURN to the stores. Please call our customer care team:
855-562-5599 to help you with any
issues or concerns you might have.
FOR COMMERCIAL USE & PROFESSIONAL INSTALLATION
We’re here to help! prosales@lockly.com locklypro.com/support
© Copyright 2022 Lockly All rights reserved US Patent NO. US 9,881,146 B2 | US
Patent NO. US 9,853,815 B2 | US Patent NO. US 9,875,350 B2 | US Patent NO. US
9,665,706 B2 | US Patent NO. US 11,010,463 B2 | AU Patent NO. 2013403169 | AU
Patent NO. 2014391959 | AU Patent NO. 2016412123 | UK Patent NO. EP3059689B1 |
UK Patent NO. EP3176722B1 | Other Patents Pending The Bluetooth® word mark and
logos are registered trademarks owned by the Bluetooth SIG, Inc. , and any use
of such marks by Lockly is under license. Other trademarks and trade names are
those of their respective owners. Google, Android and Google Play are
trademarks of Google LLC.
IMPGD698D20230106
References
- Lockly Pro-Total Access Solution for Properties & Offices
- VISION DUO (698D) - Lockly Pro
- Support Page - LocklyPRO
- Lockly Pro-Total Access Solution for Properties & Offices
- Support Page - Lockly Pro
- P65Warnings.ca.gov
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>