MARMITEK S2 Pro Wireless HDMI Instruction Manual
- June 6, 2024
- MARMITEK
Table of Contents
MARMITEK S2 Pro Wireless HDMI
the wireless presentation system
Set content
Stream T2 Pro Transmitter
HDMI extension cable USB 2.4 GHz cable Stream R2 Pro Receiver
HDMI adapter Micro USB cable
Connections
Safety instructions
Please read these instructions thoroughly before you use the device and keep them for future reference.
- This product is not a toy. Keep out of reach of children.
- Repairs or service should only be performed by qualified personnel.
Requirements
- For AirPlay use iOS 9.0 or above
- For Miracast use Android 5.0 or above
Step 1: Installing the Stream R2 Pro (receiver)
- Plug the HDMI stick into the HDMI input of the display or projector. If necessary, use the optional HDMI extension cable for optimal placement.
- Use the USB 2.4 GHz cable as power supply for the Receiver by plugging it into a free USB port of the display or projector.
Receiver LED status:
- Blue (blinking) – waiting for connection
- Blue – connected
Step 2: Installing the Stream T2 Pro (transmitter)
- Plug the HDMI stick into the HDMI output from the source (e.g. laptop or any other HDMI device).
- Some source devices can supply enough power through HDMI output to the Transmitter. Use the USB power cable when Transmitter is not working properly due to power shortage.
- If necessary, use the optional HDMI adapter (male > female) for optimal placement and installation.
Transmitter LED status:
- Red – starting up
- Red (blinking) – searching for Receiver
- Blue (blinking) – waiting for connection
- Blue – connected
- Purple – no HDMI signal
Step 3: Pairing additional transmitters (optional)
The Transmitter and Receiver supplied in this set are already paired. However,
when adding an additional Transmitter (Stream T2 Pro) it must be paired with
the Receiver.
- Power ON the Receiver and wait until it has started up and the home page appears on the screen.
- Ensure all other available Transmitters are powered OFF.
- Power ON the Transmitter and wait around 15 seconds. The indicator LED will change from static red to static blue and “Pairing Successful” will appear on the screen.
Step 4: Connect the Receiver to your Wi-Fi (optional)
The Receiver can be connected to your wireless router through Wi-Fi for easy
connection with AirPlay and Miracast.
- Open the Wi-Fi settings on your laptop or smart device, connect to the SSID “Stream S2 Pro” and enter the password displayed on the screen.
- Open the browser on your laptop or smart device and enter the IP address displayed on the screen.
- Select the SSID from the wireless router and enter the password.
- Once connected the SSID from the wireless router is displayed on the screen.
Start Presenting
Switch your display or projector ON and wait until the home screen appears on the screen. Follow the instruction on the screen to connect your PC or laptop by using the Transmitter or simply use the AirPlay or Miracast screen mirroring function from your smart phone or tablet.
Technical specifications
- Video resolution
- PC resolution
- HDMI standard
- Audio formats
- max. 1080p@60Hz
- PC resolution max. 1920 x 1080
- HDMI standard HDMI 1.4 / HDCP 1.3
- Audio formats PCM stereo
- Operational frequency IEEE 802.11ac, 5GHz, 2T2R
- Authentication Protocol WPA2 (WPAS-PSK / WPA2-Enterprise)
- Security AES 128 bit
- Operating range up to 20 meters (line of sight)
- Latency < 120 ms
- Video compression H.264
- Wireless streaming AirPlay, Miracast, DLNA
- Multiple transmitters up to 20
- Power 5VDC 0.5A
- Dimensions 83 x 32 x 13mm
- Weight 27.1g
Declaration of Conformity
Hereby, Marmitek BV, declares that the Stream S2 Pro is in compliance with the essential requirements of the 2014/53/EU Directives. Full Declaration of Conformity is available at www.marmitek.com/en/declarations-of- conformity/