TDK ANT162442DT-2001A2 Antennas User Manual
- June 5, 2024
- TDK
Table of Contents
TDK ANT162442DT-2001A2 Antennas
This module is intended for OEM integrators only
Per FCC KDB 996369 D03 OEM Manual v01 guidance, the following conditions
must be strictly followed when using this certified module:
KDB 996369 D03 OEM Manual v01 rule sections
List of applicable FCC rules
- This module has been tested for compliance with FCC Part 15, 2.3 Summarize the specific operational use conditions
- The module is tested for standalone mobile RF exposure use conditions.
- Any other usage conditions such as co-location with another transmitter (s) or being used in a portable condition will need a separate reassessment through a class II permissive change application or new certification.
Limited module procedures
- Not applicable
Trace antenna designs
- Not applicable
RF exposure considerations
This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. If the module is installed in a portable host, a separate SAR evaluation is required to confirm compliance with relevant FCC portable RF exposure rules.
Antennas
The following antennas have been certified for use with this module; antennas of the same type with equal or lower gain may also be used with this module. The antenna must be installed such that 20 cm can be maintained between the antenna and users.
| Brand | TDK |
|---|---|
| Model | ANT162442DT-2001A2 |
| Max Gain | 2.4GHz: 2.1 dBi |
NII-1,NII-2A: 1 dBi
NII-2C: 1.5 dBi
NII-3: 2.3 dBi
Antenna Type| Chip
Antenna connector| N/A
Label and compliance information
The final end product must be labeled in a visible area with the following: “Contains FCC ID: HFSJA1”. The grantee’s FCC ID can be used only when all FCC compliance requirements are met.
Information on test modes and additional testing requirements: This transmitter is tested in a standalone mobile RF exposure condition and any co- located or simultaneous transmission with another transmitter (s) or portable use will require a separate class II permissive change re-evaluation or new certification.
Additional testing, Part 15 Subpart B disclaimer
This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for compliance with this portion of rule requirements if applicable. As long as all conditions above are met, further transmitter tests will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as shown in this manual.
OEM/Host manufacturer responsibilities: OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC rules. This module must not be incorporated into any other device or system without retesting for compliance as multi-radio and combined equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>