SCOSCHE CPPDRLK-SP USB Relocator for Apple CarPlay and Android Auto with Power Delivery User Guide
- June 5, 2024
- Scosche
Table of Contents
CPPDRLK-SP USB Relocator for Apple CarPlay and Android
Auto with Power Delivery
User Guide
IMPORTANT!
DO NOT RETURN THE PRODUCT TO THE RETAILER
IF YOU NEED ASSISTANCE OR REPLACEMENT PARTS CALL US TOLL FREE t-800 38341490
HOURS: ISON FFU SASS:30PM (PST)
SATURDAY SANI4P11 (PST)
LIABILITY DISCLAIMER
This Instruction manual is based on carefully documented data and research
by Scosche Industries Inc. and cannot be held responsible for
discrepancies/inconsistencies that may occur due to the vehicle manufacturing
changes or options, or damages that may occur In the vehicle during the
installation of components while using this manual.
If you have any further questions, can our ton free technical helpline:
1-800-363-4490 x1 or visit us online at
www.scoscht.com/contact
12V SOCKET REMOVAL
INSTALLATION NOTE: These instructions are provided as a general guide and may differ from your particular vehicle. If you have difficulty removing the 12V lighter/ power socket in your vehicle, contact our tech support at 800-363-4490 ext. 1.
Snap-in Type:
- Use a panel removal tool (PRT) to unsnap socket assembly (Figure 1 ).
- Carefully slide out, unplug the power connector and remove it (Figure 2).
Thread-in Type:
- Gain access the rear of the 12V socket assembly in the vehicle (not shown).
- Unplug electrical connections (not shown).
- Un-screw the locking collar (counterclockwise), carefully slide the socket out, and remove it (Figure 3).
CUSTOM INSTALL
- Choose an area of the dash that is free of obstructions behind the panel and allows the cables to reach the rear inputs of the stereo.
- Use a hole saw or step drill bit to drill a 1″ (26mm) hole for the 12V POWER plug (Figure 4).
NOTE: Use of the protective (FIGURE 6) cover is recommended, particularly
for marine applications. Install the cover prior to installing the CPPDRLK-SP
plug into the location.
INSTALLING THE CPPDRLK-SP
- Remove the locknut from the CPPDRLK-SP housing (FIGURE 6).
- Feed the connecting cable along the body of the unit through the 1 “(26mm) diameter hole (FIGURE 7).
- Thread the backing/lock nut onto the CPPORLK-SP housing from the rear and carefully tighten in a clockwise direction, do NOT over-tighten (FIGURE 8).
CONNECTING THE CPPDRLK-SP
-
Connect the USB Cable from the CPPDRLK-SP to the corresponding USB Input or dongle from the back of the stereo.
-
Connect the”+” Positive Male terminal from the back of the CPPDRLK-SP to a +12V Accessory Switched power source.
(Socket replacement): Use the existing power lead from the previous power socket.
(New Installation): Route a new power wire (not included) to a switched power source such as the vehicle’s fuse block. -
Connect the Negative Male terminal from the back of the CPPDRLK-SP to Chassis Ground. (Socket replacement): Use the existing Ground wire from the previous power socket.
(New Installation): Route a new wire (not included) directly to Chassis Ground. -
Once the CPPDRLK-SP is securely mounted and connected. Re-assemble and remaining trim parts to complete your installation.
® 2021 SCOSCHE INDUSTRIES, INC
Documents / Resources
|
SCOSCHE CPPDRLK-SP USB Relocator for Apple CarPlay and Android Auto with
Power
Delivery
[pdf] User Guide
CPPDRLK-SP, USB Relocator for Apple CarPlay and Android Auto with Power
Delivery, CPPDRLK-SP USB Relocator for Apple CarPlay and Android Auto with
Power Delivery
---|---
References
- Contact Us | Get help | Technical and Customer Service Support
- Product registration | Register your purchase
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>