SEALEY LED316 5W COB & SMD LED Rechargeable 3 in 1 Inspection Light Instructions

SEALEY LED316 5W COB & SMD LED Rechargeable 3 in 1 Inspection Light

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY

GENERAL SAFETY

• Ensure the lamp is fully charged before initial use.
• DO NOT turn the lamp on when it is being charged.
• DO NOT shine directly into your, another person’s, or an animal’s eyes.
• DO NOT allow children to use the lamp.
• DO NOT handle or move the lamp whilst it is being charged.
• DO NOT use the lamp if you suspect that the battery or the lamp casing is damaged.
• DO NOT leave the battery in a discharged state, recharge the battery immediately. Before storage, fully recharge the battery, and subsequently recharge the battery at least once every six months of non-use.

BATTERY SAFETY

• WARNING! To reduce the risk of burns or fire:
• DO NOT attempt to open, disassemble, modify or service the battery pack.
• DO NOT crush, puncture, short external contacts or dispose of in fire or water.
• DO NOT expose to temperatures above 60°C (140°F).
• Recycle or dispose of used batteries as stipulated by local regulation.
• If the electrolyte in the cells gets on your skin, thoroughly wash with soap and water. If it gets in your eyes, rinse thoroughly with cool water and seek immediate medical attention.

INTRODUCTION

5W COB LED Directional light, 3W SMD LED front torch, 3W COB LED front strip lighting and strobe effect. Also featuring 180° rotational stand, magnet, hook and clip for multiple uses. Supplied with Micro USB charging lead. Maximum of 300 lumens and 7 hour run time. Li-ion battery with charge indicator.

SPECIFICATION

• Model No :………………………………………………………… LED316
• Battery :……………………………………………………………….. Li-ion
• Charging Time :……………………………………………………. 2.5hrs.
• IP Rating :……………………………………………………………….IP20
• LED Qty :…………………………………………………………………….3
• LED Type :………………………….. 2 x COB LED + 1 x SMD LED
• Lumen Outputs ……………………………………………………. 300lm
• Operating time ……………………………………………. 2.5 – 7 hours

IMPORTANT WARRANTY INFORMATION

The battery fitted to this lamp is considered to be a consumable item and its ability to accept a charge will reduce over time. We will provide a warranty against mechanical and electrical defects for a period of one year – this DOES NOT cover fair wear and tear. If the battery is not properly charged before first use, or regularly conditioned, its capacity will diminish. Under these circumstances, we will not replace the battery regardless of whether it is less than one year old.

OPERATION

Refer to fig.1

1. Connect the USB lead to the socket on the rear of the lamp. Plug USB lead into a power supply and turn on. When the battery has fully charged the LEDs will turn GREEN.
2. Direct the lens away from your eyes before switching on.
3. Toggle the lamp between the end light and the two side lights using the mode selector switch (fig.1).
4. The lamp may be suspended by the hook or attached to any ferrous surface by using the magnet.

MAINTENANCE

1. Keep the torch clean by wiping it with a damp cloth.
2. Store torch in a dry childproof area.

WEEE REGULATIONS

Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.
BATTERY REMOVAL
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling center, and disposed of in a manner that is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications, and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Address: Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>